Installation Manual

ManualsBrandsPanduit ManualsAudioPre-Loaded Fiber Drawer 12 Duplex SC 1 R

For Technical Support: www.panduit.com/resources/install_maintain.asp

INSTALLATION INSTRUCTIONS

FS004A

FD1W12BUDE2KZ

Opticom Pre-Loaded Fiber Drawers

Part Numbers: FD1W6**DSC, FD1W12**DSC, FD1W12**DLC, FD1W24**DSC,

FD1W24**DLC, FD1W12BUDE2KZ, FD1W24BUDE2KZ

FD1W12**DSC

FD1W24**DLC

FD1W6**DSC

FD1W12**DLC

Accessory Kit

(4) #12-24 x 1/2" Screws, (4) M6 Screws, (1) Fiber Caution Label, (1) Laser Warning Label, (2) Slack Spools and (1) PG11 Gland.

** Denotes adapter color/fiber type: EI (Electric Ivory/OM1 62.5/125µm), BL (Black/OM2 50/125µm), AQ (Aqua/OM3 10Gig 50/125µm),

or BU (Blue/OS1/OS2 9/125µm).

Knockouts for Blown Fiber Adapters

(4 places)

Knockouts for Rubber Grommets

(2 places)

30mm Diameter

Knockouts for PG11 Glands

(2 places)

20mm Diameter

Drawer Release

Latches

Provisions for Port

Identification Labeling

FD1W24BUDE2KZ

Page 1 of 4

FD1W24**DSC

Summary of content (4 pages)

PAGE 1
Opticom Pre-Loaded Fiber Drawers Part Numbers: FD1W6**DSC, FD1W12**DSC, FD1W12**DLC, FD1W24**DSC, FD1W24**DLC, FD1W12BUDE2KZ, FD1W24BUDE2KZ INSTALLATION INSTRUCTIONS © Panduit Corp. 2011 FD1W6**DSC FD1W12**DSC FS004A FD1W12**DLC FD1W12BUDE2KZ FD1W24**DLC FD1W24BUDE2KZ FD1W24**DSC Accessory Kit (4) #12-24 x 1/2" Screws, (4) M6 Screws, (1) Fiber Caution Label, (1) Laser Warning Label, (2) Slack Spools and (1) PG11 Gland. ** Denotes adapter color/fiber type: EI (Electric Ivory/OM1 62.
PAGE 2
INSTALLATION INSTRUCTIONS © Panduit Corp. 2011 FS004A Mounting 6mm or #12-24 x 1/2" screws provided (4 places) Mount the enclosure to rack using four (4) 6mm or #12-24 x 1/2" screws provided. Drawer Opening and Removal Release latches Slide drawer forward Rotate up and remove Grommet, Gland, and Spool Installation Spool Rubber Grommet PG11 Gland Remove knockouts and insert grommets and/or glands as shown above. Remove the liner from the tape underneath each fiber management spool.
PAGE 3
© Panduit Corp. 2011 INSTALLATION INSTRUCTIONS Typical Cable Routing Options PG11 Gland with Pre-Terminated Trunk or Field Termination Grommet with Pre-Terminated Trunk or Field Termination Grommet with splicing using the FSC24 Splice Sleeve Holder PG11 Gland with splicing using the FSC24 Splice Sleeve Holder For Technical Support: www.panduit.com/resources/install_maintain.
PAGE 4
INSTALLATION INSTRUCTIONS © Panduit Corp. 2011 Typical Cable Routing Options (continued) FOSM installation: Place double stick tape underneath FOSM and locate the FOSM in the enclosure as shown. Grommet with splicing using the Fiber Optic Splice Module (FOSM) Blown Fiber with splicing using the FSC24 Splice Holder Blown Fiber with fusion splicing using the Fiber Optic Splice Module (FOSM) PG11 Gland with splicing using the Fiber Optic Splice Module (FOSM) E-mail: techsupport@panduit.