Installation Manual

ManualsBrandsPanduit ManualsAudioRack Mount Fiber Enclosure, Black

For Technical Support: www.panduit.com/resources/install_maintain.asp

INSTALLATION INSTRUCTIONS

FS006D

Page 1 of 11

Opticom QuickNet Rack Mount

Fiber Cassette Enclosures

Part Numbers: FCE1U, FCE1UA, FCE2U

1 - ENCLOSURE

2 (3) - Tak-Tys, 6" pcs.

2 (3) - ADHESIVE MOUNTS

2 - SLACK SPOOLS

1 (2) - #10-32 x 3/8" SCREW

3 (4) - #10-32 HEX NUTS

WARNING: UNMATED CONNECTORS MAY EMIT INVISIBLE LASER RADIATION. DO NOT LOOK DIRECTLY INTO THE END OF THE

CONNECTOR. DO NOT INSPECT WITH MAGNIFYING DEVICES. MAINTAIN DUST CAPS ON UNMATED CONNECTORS.

CAUTION:

Fiber optic cable is sensitive to excessive pulling, bending, and crushing forces. Consult the manufacturer’s cable specification sheet for the

specific cable in use.

Follow TIA/EIA-568-A, 569, 606, and 607 installation guidelines where applicable.

Care should be taken when opening or closing a fully loaded drawer in order to protect the fiber components.

CONTENTS: (#) indicates FCE2U quantity

3 (4) - CABLE ENTRY GROMMETS

4 - #M6 x 1 SCREWS

1 (2) - STRAIN RELIEF BRACKET

4 - CABLE TIES, PLT2S-M0

2 (4) - PLUNGER AND GROMMETS

2 (4) - BEND RADIUS CONTROL CLIPS

4 - #12-24 x 1/2" SCREWS

1 - CAUTION LABEL

1 - LASER WARNING LABEL

3 - ADHESIVE BEVEL ENTRY CLIPS

Mounting bracket

Trunk or interconnect

cable entry location

ASSEMBLY VIEW

Strain relief

bracket

Bend radius

control clip

Door assembly

(shown in the

open position)

FCE2U

Figure 1

Plunger and

grommet

Enclosure

sliding drawer

Fiber Adapter Panels (FAPs):

Up to 4 for FCE1U & FCE1UA

Up to 8 for FCE2U

(sold separately)

FCE1UAFCE1U

Enclosure

Summary of content (11 pages)

PAGE 1
Opticom QuickNet Rack Mount Fiber Cassette Enclosures Part Numbers: FCE1U, FCE1UA, FCE2U INSTALLATION INSTRUCTIONS © Panduit Corp. 2015 FCE1U FS006D FCE1UA FCE2U 3 (4) - CABLE ENTRY GROMMETS 4 - #M6 x 1 SCREWS 1 (2) - STRAIN RELIEF BRACKET 4 - CABLE TIES, PLT2S-M0 2 (4) - PLUNGER AND GROMMETS 2 (4) - BEND RADIUS CONTROL CLIPS 4 - #12-24 x 1/2" SCREWS 1 - CAUTION LABEL 1 - LASER WARNING LABEL 3 - ADHESIVE BEVEL ENTRY CLIPS CONTENTS: (#) indicates FCE2U quantity 1 - ENCLOSURE 2 (3) - Tak-Tys, 6" pcs.
PAGE 2
INSTALLATION INSTRUCTIONS © Panduit Corp. 2015 FS006D Preparation and Rack Mounting Determine where the cable will enter the enclosure. Carefully remove the knock-out so as not to damage the surrounding sheet metal. DO NOT Install grommet at this stage. Grommet will be installed after the enclosure is mounted to the rack. Figure 2 Place the mounting brackets at the desired position on the rack. Mounting brackets Figure 3 Mount the enclosure to the rack using (4) #12-24 x 12" screws.
PAGE 3
INSTALLATION INSTRUCTIONS © Panduit Corp. 2015 FS006D Grommet Cutting Diagram After the enclosure is mounted to the rack, determine the size of the innerduct that will be used to bring the cable into the enclosure. Prepare grommet(s) according to the proper cutting diagram to the left. Cut out the small circle for 1" dia. innerduct Cut out the small circle for 1-1/4" dia. innerduct Cut the straight lines for smaller bundle sizes Cut out the large circle for 1-1/2" dia.
PAGE 4
INSTALLATION INSTRUCTIONS © Panduit Corp. 2015 FS006D QuickNet Cassette Installation (cassettes not included) Depress spring latch and pull sliding tray out to the extended position. Spring latch Figure 7 Insert QuickNet Pre-Terminated Fiber Optic Cassettes into the enclosure as shown. Once mounted, fully seat NyLatch fasteners to secure the cassettes. QuickNet Cassettes: Up to 4 for FEC1U & FCE1UA Up to 8 for FCE2U Figure 7A Fully extend drawer to ensure proper amount of slack is used.
PAGE 5
INSTALLATION INSTRUCTIONS © Panduit Corp. 2015 Tak-Ty cables to fence Grommet Fixed Tak-Ty “A” Cable length between point “A” and point “B” is approx. 34" [.864m]. Route fiber through grommet to fiber cassettes as shown. Leave enough slack so when the drawer is fully extended the cables are not put under tension. DO NOT use so much slack that the drawer cannot be returned to its home position. (See Figure 7D) Use Tak-Tys to secure fiber cords at cable entry location and other points as shown.
PAGE 6
INSTALLATION INSTRUCTIONS © Panduit Corp. 2015 FS006D Field Termination or Pre-Terminated Trunk Installation Fiber Adapter Panels (FAPs): Up to 4 for FEC1U & FCE1UA Up to 8 for FCE2U Slack spools Place slack spools over #10-32 studs on sliding tray. Secure with #10-32 hex nuts and/or adhesive mounts (make sure to punch hole into adhesive mounts). Note spool orientation. Position FAPs between upright flanges as shown. Once mounted, fully seat NyLatch fasteners to secure FAPs.
PAGE 7
INSTALLATION INSTRUCTIONS © Panduit Corp. 2015 Tak-Ty cables to fence as needed. Grommet “A” Fixed Tak-Ty Cable length between point “A” and point “B” is approx. 36" [.914m]. Sub-unit tubes Free floating Tak-Ty FS006D Route fiber through grommet as shown. Use enough cable length to ensure one complete loop (approx. 52" [1.32m]) of individual fibers around slack spools. Leave enough jacketed slack so when the drawer is fully extended the cables are not put under tension.
PAGE 8
INSTALLATION INSTRUCTIONS © Panduit Corp. 2015 FS006D FOSM Fiber Optic Splice Module Installation (FOSMs not included) FOSM: Up to 4 for FEC1U & FCE1UA Up to 8 for FCE2U Break off FOSM latch on top module only Place “L” shape support brackets over #10-32 studs on sliding tray, note orientation. Place first FOSM on top of “L” shape support brackets and secure with #10-32 hex nuts. Remaining FOSMs are stacked on top of each other and snap in place.
PAGE 9
INSTALLATION INSTRUCTIONS © Panduit Corp. 2015 Tak-Ty cables to fence FS006D Grommet “A” Fixed Tak-Ty Sub-unit tubes Cable length between point “A” and point “B” is approx. 36" [.914m]. Free-floating Tak-Ty “B” Route fiber through grommet as shown. Use enough cable length to ensure one complete loop (approx. 45" [1.15m]) of individual fibers around FOSM slack spools.
PAGE 10
© Panduit Corp. 2015 INSTALLATION INSTRUCTIONS FS006D Patch Cord Bend Radius Control Clip Installation Plunger and grommet Bend radius control clips Plunger and grommet Figure 10 Bend radius control clip Sliding tray flange Slide bend radius control clip over sliding tray flange as shown. Push plunger/grommets through bend radius control clip and sliding tray flange hole. Fully seat plunger into grommet to secure the clip. Repeat for the other side.
PAGE 11
© Panduit Corp. 2015 INSTALLATION INSTRUCTIONS FS006D Door Re-Attachment Re-install front door and rear door assemblies, if removed during fiber installation. Attach Laser Warning Label and Caution Label where they are clearly visible. Figure 12 E-mail: techsupport@panduit.com For Instructions in Local Languages and Technical Support: www.panduit.com/resources/install_maintain.asp www.panduit.