Manual

_ _ !i!_ _!_, !_ _!!_i!! i_ _!_!_!i__!_i_i !!i!,z!!! __ i!!_i_i!!_!!!!i_!_!__!i!_z_i!!_!!!!!!!_i!¸i_i_i!_!_!ii_ii!!!!_!i!!i!_i_i!!i!!!!_!!i!iiiiiii_!_!!iiii_i_!!!!_!iiii!_!_!_iiiiiiii_!_!!iiiiiiii_!!i!iiiii!_!_!iii!ii!iii_ii!i!i!i!i!i_iz!_i!!i!i!_ _:_ __:_____z_:_ __ __ _ _ __ ___ _ _ _ __ __ __ _¸_i_iiiii_i__z_i_iiiiiii!iiiii_ii_iiiiiii_i_i_iii_iii_i_i_i_iiii_i_i_iiii_i_i_i_i_i_i_iiiiiiiiii_i_i_iil
_iiiiiii_iiiii_iiiiii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiii_iiiiii_iiiiiiiiiiiiiii_iiii_i iiiiii!iiiiiiiiiiiiii_!iiiii!iiiii!ii!iiiiiii!iiiiiii_ iiiiii_iiiii_iiiii_iiiii_iiii_ii i_ iiii_iii _iii_ii_iiii_ii _ii_ i i_i ii_ i_iiiil _iiii_iii_i_i_i_i_i_i_ii_i_i_iii_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_ _i_'_'_ _'__i_'_'_'_ _ii_
Connect the AM loop antenna. /,_ Connect the right (R) and left (L) speaker
1. Attach the antenna holder to the rear panel of the "7' cables.
tuner/sound processor.
2. Clamp the AM loop antenna to the antenna holder and
connect the antenna terminal to the rear panel of the
tuner/sound processor.
3. Position the loop for the best reception.
Antenna holder
Press in until you hear a click.
AM loop antenna
Press hard enough to get it
fixed firmly in the place,
with a click.
You may attach the AM antenna holder with a screw (in-
cluded) to a rack or other structure. In this case, attach as
shown in _
-- -- Rack or other structure
To minimize noise pickup, keep the AM loop antenna cord
along the heat outlet grille, and away from the flat cables.
• Be sure to connect speaker cables before connecting the
AC power supply cord.
eThe load impedance of any speaker used with this unit must
be 6-8£_.
• Match the two wires from the left and right speaker cables
with the same colored levers of the speaker terminals, then
insert the wires into the respective terminals.
1. Strip off the outer
covering, and twist =_====,, _),
the center conductor. 15mm
2.
Make sure the bare ends of the wires are not unravelled.
(If they are, twist them tight again.) I'_
(For SC-CH717) I I_--_]
Insert the wire to the rear panel .._11_ I _
of the speakers, and then pull _ I
down the lever. _ "'J
(For SC-CH515)
Q Tilt the lever back
and insert the wire.
(_ Close the lever and
pull the cord gently
to be sure that it is
secured.
3. Insert the wire to the
rear panel of the
amplifier, and close the lever.
• To prevent damage to circuitry, J,_F_ t
never short-circuit positive (+)
and negative (-) speaker wires.
• Be sure to connect only positive (red) wires to positive (+)
terminals and negative (black) wires to negative (-) ter-
minals.
(For SC-CH717 only)
Connect the surround speaker cord.
Rear panel of Rear panel of
the amplifier the speakers
Connect the AC power supply cord after you
have connected all other cables.
9