P-01E INSTRUCTION MANUAL ’12.
Thank you for selecting the “P-01E”. Read this manual before use to correctly operate your P-01E. About manual of P-01E Basic Package The operating procedures for the P-01E are also published as in P-01E Handset Desktop Holder P51 (With Warranty and Back Cover P58) “使いかたガイド (Guide)” on-screen manual installed onto your FOMA terminal, and “Instruction Manual (Detailed Version)” as a PDF.
Contents Part Names and Functions ············ 2 FOMA Terminal ······························ 4 Precautions···································· 5 Handling Precautions ·················· 12 Waterproof/Dust-proof Performance ··· 15 Introduction ▶ P.
Introduction Part Names and Functions ❶ ❷ ❶Air vent For adjusting the pressure inside the FOMA terminal ❷Earpiece For listening to the other party’s voice ❸ ❺ ❻ ❼ ❽ ❾ 2 cCamera key/1Seg key rClear key/i-Channel key ❸Display ii-mode key/i-αppli key ❹oCommand navigation key For operating functions and menus hPower/End key ❺mMenu key For showing the Main Menu ❹ Microphone For speaking to the other party ❻lMail key For showing the Mail Menu ❼dStart key For starting to talk Cal
Back cover Remove this when attaching/removing the battery pack, docomo mini UIM card, and microSD card. Infrared data port For using infrared communication and the infrared remote control Strap hole xMulti key For showing the Task menu ❶ One-push open button For opening the FOMA terminal (Be careful not to drop the FOMA terminal by the rebound when opened.) For using earphone Connect an optional connector-terminalcompatible earphone.
Introduction FOMA Terminal 4 P-01E supports W-CDMA system. Because the FOMA terminal uses radio waves, you cannot use it in places where the radio waves do not reach, where they are weak even outdoors, such as inside tunnels, basements, or buildings, or out-of-service area. You might not be able to operate the FOMA terminal even when you are in a place with a fine view such as in a high-rise building or apartment.
Precautions ALWAYS FOLLOW THESE DIRECTIONS Danger This symbol indicates that incorrect handling will almost certainly cause death or serious injury. Warning This symbol indicates that incorrect handling poses a risk of causing death or serious injury. Caution This symbol indicates that incorrect handling poses a risk of causing a slight injury or damage to the product or property. ■ The following symbols show specific directions: Denotes actions prohibited to do.
Introduction General precautions for FOMA terminal, batteries, adapters, desktop holder, and docomo mini UIM card Don’t Don’t Do not use, store, or leave the FOMA terminal or its accessories in places with a high temperature (such as near fire, near heating appliances, inside a kotatsu or near other furniture with heating elements, in places exposed to direct sunlight, or in cars heated by the sun). Fire, burns, or injury may result.
Do Precautions for FOMA terminal Warning Don’t Do not directly point the infrared data port at someone’s eyes during transmission. Doing so may harm the person’s eyes. Don’t While using infrared communication, do not point the FOMA terminal’s infrared data port at a home electrical appliance which is equipped with an infrared device. The infrared device may malfunction, and possibly cause an accident.
Introduction Do Do 8 Turn off the FOMA terminal when near electronic devices using high-precision control or weak signals. The FOMA terminal may cause the electronic devices to malfunction and have other adverse effects. ※ Electronic devices that may be affected: Hearing aids, implanted cardiac pacemakers, implanted defibrillators, other electronic medical equipment, fire alarms, automatic doors and other automatically controlled devices.
Precautions for batteries ■ Check the description on the label of the battery pack for the type of battery. Type Lithium-ion battery Danger Don’t Don’t Don’t Don’t Do Do not let any metal object such as a wire come in contact with the battery terminals. Also do not carry or store the battery together with any metal objects like a necklace. Otherwise, the battery pack may ignite, burst or overheat and its electrolyte may leak.
Precautions for adapters and desktop holder Introduction Warning Don’t Don’t Don’t Don’t Don’t 10 Do not use the adapter if its cord has been damaged. Fire, burns or electric shock may result. Do not use the AC adapter and desktop holder in humid places such as a bathroom. Fire, burns or electric shock may result. The DC adapter is for use only in a negative (-) grounded vehicle. Do not use it in a positive (+) grounded vehicle. Fire, burns or electric shock may result.
Before cleaning, pull the power plug out of the outlet or cigarette lighter socket. Pull the Fire, burns or electric shock may power plug result. Notes on using near electronic medical equipment ■ The description below meets “Guidelines on the Use of Radio-communication Equipment such as Cellular Telephones – Safeguards for Electronic Medical Equipment” by the Electromagnetic Compatibility Conference Japan.
List of materials used Introduction ■P-01E Handset/Back Cover P58/Battery Pack P23 Where it is used Display Outer casing surface, Battery surface, Battery surface (Hinge side) Connector terminal Connector Body terminal Fitting pin cover area Packing Panel of camera lens area, Display panel, Sub-display panel Side key Around the side key Charging terminal Material/Finishing PC/UV coating Stainless steel/ nickel plating + tin plating PC/UV coating Elastomer Silicon rubber PMMA/hard coating ABS ABS/UV co
■Carefully read each instruction manual attached to optional items. ■Do not leave the camera in places exposed to direct sunlight. Pixels may be discolored or burns may Notes on handling the FOMA terminal result. ■Avoid using in extremely high or low ■When using the FOMA terminal, temperatures. ensure that you shut the cover for the The FOMA terminal should be used within connector terminal. a temperature range of 5°C to 40°C and a Dust or water might enter into the FOMA humidity range of 45% to 85%.
Introduction 14 ■Charge the battery in a place with an appropriate ambient temperature of 5°C to 35°C. ■The usable time of the battery differs depending on the usage environment or its remaining life. ■Depending on how the battery pack is used, it might swell as its operating life becomes short, but this is not a problem.
Waterproof/Dust-proof Performance Sea/pool Introduction Your P-01E is capable of IPX5※1 and IPX7※2 waterproof performance and IP5X※3 dust-proof performance if the connector terminal cover and back cover are firmly closed and no clearance gap and float found in them. ※1 IPX5 means that the P-01E maintains its performance as a phone even after a water jet flow has been sprayed over the FOMA terminal from all directions under conditions where water in a volume of 12.
Introduction Opening/Closing the Connector Terminal Cover Removing/Attaching the Back Cover ■Opening the connector terminal cover ① Hook your finger over the groove, pull out the cover to direction A, and rotate it as direction B. ■Removing the back cover ① Using the “ ” part of the FOMA terminal, lift up in the direction of the arrow to remove the back cover.
Caution ･ Even the slightest sands entered from the connector terminal cover or back cover could cause water to enter the inside of the FOMA terminal. ■About the connector terminal cover and back cover Do not open or close them with gloves put on hands. Fine dirt might adhere to the contact surface of the packing. Be careful that no fibers adhere to the packing when you try to wipe off moisture with a clean dry cloth. Do not peel the packing off.
Introduction Draining Water If you operate the FOMA terminal with water drops left adhered to, the volume level from the speakers might be decreased or sound quality vary. Moisture may have entered inside through the clearance gap of the keys or hinges.
Before Using When you remove the docomo mini UIM card Pull out the tray, and then slide the docomo mini UIM card slowly to pull it out. After pulling out the tray until about half of the docomo mini UIM card is visible, pull out the docomo mini UIM card by sliding it out. Attaching docomo mini UIM card/ Battery Pack To insert the docomo mini UIM card/battery pack, remove the back cover and insert. (See page 16) Insert the docomo mini UIM card. 1.
4 Charging Charging Using Desktop Holder Call/Charging indicator AC Adapter’s plug Basic Operation Connector Charging Using AC Adapter Power socket AC Adapter Power socket AC Adapter AC Adapter’s plug Connector terminal Call/Charging indicator Cover Engraved surface Connector Release buttons Desktop Holder Engraved surface 1 With the engraved surface of the connector of the AC Adapter (option) face up, plug the connector straight into the connector terminal of the desktop holder provided.
For detaching, pull out the connector horizontally while pressing the release buttons. Malfunction could result if you try to pull it forcibly. When charging starts, the Call/Charging indicator lights in red. When charging is completed, it turns off. Notifying Your Caller ID on the Other Party’s Phone 1 Deactivate▶ON Turning Power ON Press and hold h for at least one second. After the notes of waterproof and Wake-up display are displayed, the Stand-by display appears. To turn off the power 1.
Screen Explanation Viewing Display/Icon Status icon Battery level (estimate) ··········· A microSD card is inserted. Basic Operation ·········· Vibrator is set. Full Low When is shown, charge the battery. Depending on the usage state, the battery level indication might significantly vary. ·········· Ring Volume is set to “Silent”. ·········· In Manner Mode ···· An alarm is set.
Notification icon ······ New i-mode mail or SMS ······ Missed call ······ Record message Sub-display Various information is displayed on the sub-display such as the following: Information is displayed in cases such as when you press x with the FOMA terminal closed. ······ Videophone record message ····· 1Seg has automatically terminated (ECO NAVI). Stand-by shortcut ····· i-concier Clock Dialing Receiving a call When a missed call is found ” appears in cases such as when the “ FOMA terminal is closed.
Navigation Displays and Key Operations Operating Command Navigation Key Basic Operation Key operations you can perform while you are operating a function are shown at the bottom of the display. (Navigation displays) ■Key assignments and basic navigation displays Moves the cursor or highlighted display up. (Hold down to scroll continuously.) Scrolls the page up. Vo Moves the cursor to the right. Scrolls forward page by page. (Hold down to scroll continuously.) Oo Fixes the operation.
Simple Menu Menu Operation Main Menu Press m from the Stand-by display to show Main Menu. In this manual, the descriptions of operating procedures are given mainly starting with the Stand-by display. Submenu When “ ” is displayed at the lower left of the display, you can use functions such as Store, Edit, and Delete by pressing m. Menu icon name In this manual, the item Display the submenu of a Phonebook entry names shown here are described in operating procedures, etc.
Functions Starting with Simple Operation Depending on the function, you can start it either by selecting a menu item or by key operation from the Stand-by display. The following are the functions you can start by pressing keys for at least one second. Basic Operation Key Performance ■Registering function 1. Q, W or E (for at least one second) ▶Select an item▶YES Oo Sets/Releases Keypad Lock. Zo Shows the Registration display for Phonebook entries. Xo Starts i-widget. c Starts 1Seg.
Using MyFACE docomo Palette UI The docomo Palette UI is a user interface that allows you to easily access a variety of functions and services from the center of the Stand-by display. You can freely customize this interface. The MyFACE display appears to the left and right of the Stand-by display, and the Shortcut display appears below. MyFACE is a convenient function that allows you to download MyFACE content from a site and register the content to the left or right of the Stand-by display.
Using Shortcut A list of shortcuts appears at the bottom of the Stand-by display. By creating shortcuts to, for example, functions you use frequently, you can use certain functions immediately. Basic Operation 1 2 Press Xo. Use No to highlight a Stand-by shortcut and press Oo( ). You can start the shortcut. Stand-by shortcut 1 m▶便利ツール (Tool) ▶使いかたガイド (Guide) Press Xo. 2 3 Use Mo to highlight a shortcut and press Oo( ). Creating Shortcuts 1.
Character Entry You can enter characters on the Registration display for Phonebook entries or the Composition display for mail messages, etc. 1 Select a input mode. Press l( Enter characters. By repeatedly pressing a numeric key, you can enter other characters assigned to the key.
Sound/Screen Setting Changing Ring Tone Changing the ring tone for incoming voice calls Basic Operation 1 m▶Setting▶Sound/Vib./Manner ▶Select ring tone▶Phone※▶Select ring tone▶Select a type of ring tone▶Select a folder▶Select a ring tone. ※To set a ring tone for mail messages, videophone calls, and so on, select the corresponding item. Adjusting Ring Volume Adjusting the ring volume for incoming voice calls 1 m▶Setting▶Sound/Vib.
Setting Keypad Sound OFF 1 m▶Setting▶Sound/Vib./Manner ▶Other sound setting▶Keypad sound ▶OFF 1 on the image. Changing Display Brightness You can adjust the brightness of the display. You can also set to automatically adjust the display brightness according to the ambient light.
Changing Font Size Changing the size of all the characters to “X-large” 1 7 (for at least one second)▶Character size▶X-large Basic Operation Select “Separate setting” when you want to set the character size of each function separately. Changing Machi-chara Setting Changing Illumination When Receiving Changing call Illumination for voice calls 1 1 ※To set illumination such as for mail messages and videophone calls, select the corresponding menu.
eco Mode Setting You can set the items for reducing battery consumption for when the eco Mode activates. 1 m▶Setting▶Battery▶eco mode setting▶Put a check mark for items to be set▶c( ) This setting ensures that the mode will be automatically set to the eco Mode when the remaining battery level has dropped to the set level or less. “Battery level” of “eco mode autostart” is set to “40%” in default. When the “eco mode autostart” is set to “ON”, “ (gray)” will be displayed.
Terminal Security Code “0000” at purchase This is a four-to-eight digit number for deleting all files or changing settings. When the display for entering the Terminal Security Code appears, enter your four-to-eight ). digit code and press Oo( “お客様サポート (User support)” is available in Japanese only. For the docomo mini UIM card, you can set two security codes, namely the PIN1 code and PIN2 code.
PIN Unblocking Key (PUK) The PIN unblocking key (PUK) is the eight-digit number for releasing the blocked PIN1 code and PIN2 code. You cannot change this code by yourself. If you enter a wrong PIN unblocking key (PUK) 10 times in succession, the docomo mini UIM card is locked. In that case contact one of docomo Shops. Various Lock Functions A variety of lock functions is installed on your FOMA terminal such as preventing illegal use of a third party, or protecting your private information.
Basic Operation Original Lock Keypad Lock You can lock functions which utilize personal information such as Phonebook entries or schedule events. 1. m▶Setting▶Lock/Security▶Lock ▶Enter your Terminal Security Code ▶Select a level for Original Lock. To release, select “OFF”. Key operations are disabled. 1. Press and hold Oo for at least one second. To release, perform the same operation. You can reset the items on “Function List”, which are indicated by .
Call Telephone 2 When an entry contains multiple phone numbers, press No to select a desired phone number. ) to make a videophone call. Press c( Making a Call/Videophone Call Making a Call by Entering the Phone Number 1 Enter a phone number starting with a city code▶Press d to make a call ▶Press h to end the call. This FOMA terminal has no inward-facing camera. Therefore, the image sent to the other party is a Chara-den image, still image, or image being shot by the outward-facing camera.
Making an International Call You can use WORLD CALL to make an international call from Japan. Contact “docomo Information Center” on the back page of this manual for inquiries about details on WORLD CALL. When using international carriers other than DOCOMO, contact them. 1 0(for at least one second) ▶Enter numbers in order of country code Connect →area code (city code) →destination phone number. You can enter “+” by pressing and holding 0 for at least one second.
Using Public Mode (Drive Mode) Once you activate Public mode (Drive mode), the guidance is played back telling that you cannot answer the call as you are currently driving or in a public place (such as a train, bus or movie theater) where you should refrain from speaking on the phone. Then, the call is disconnected automatically. 1 Press and hold a for at least one second. “ ” appears on the Stand-by display.
Using Voice Mail Service Using Call Forwarding Service 1 1 m▶TEL function▶Voice mail service To activate the service 1. Activate▶YES You can also specify a ring time. Connect To play back the message 1. Play messages▶Play (voice call) or Play (videophone) ▶YES▶Operate following the voice guidance. Using Call Waiting Service 1 m▶TEL function▶Other network serv. ▶Call waiting To activate the service 1. Activate▶YES Answer an Incoming Call during a Call Press d.
Emergency Call Using Overseas International Roaming (WORLD WING) is a service that allows you to use the FOMA terminal with the phone number and mail address you use in Japan, in a service area of the overseas carrier partnered with DOCOMO. It enables you to continue using the voice call, SMS and i-mode mail settings This FOMA terminal supports “Emergency Location Report”. When without having to make any changes.
Making a Call to Outside the Country You Stay in Available Service Overseas Connect Major Communication Service Voice call※1 Videophone call※1 SMS※2 i-mode※3 i-mode mail i-Channel※3※4 i-concier※5 i-Widget※6 Packet communication by connecting with a personal computer 42 3G ○ ○ ○ ○ ○ ○ ○ ○ 1 →area code (city code) →destination phone number. You can enter “+” by pressing and holding 0 for at least one second. Enter “81” as a country code when you make an international call to Japan.
Sending Deco-mail Mail Sending i-mode Mail Once you subscribe to i-mode, you can exchange e-mail messages over the Internet. You can attach within 2 Mbytes of up to 10 files (photos, moving pictures, etc.) with body text added. For details on i-mode mail, refer to “Mobile Phone User’s Guide [i-mode]”. 1 l▶l( )▶Enter each item. Enter a destination (mail address). You can change the color or size of characters or background color, or insert images or Deco-mail pictograms.
Sending Decome-Anime You can create impressive messages by inserting text or images into a Flash file. 1 l▶Create new Deco-Anime ▶Enter an address and subject. Connect 2 Checking New i-mode Mail You can check the i-mode Center for a new mail message or Select the text field▶Highlight a Message R/F. Decome-Anime template and press 1 Press and hold l for at least one second. c( )▶Edit characters and images ) ▶c( Sorting i-mode Mail You can use “Auto-sort” to sort received/sent i-mode mail ).
Early Warning “Area Mail” Receiving Area Mail You can receive information such as about earthquake alerts that are issued from the Japan Meteorological Agency as an Area Mail message. ” lights and the When an Area Mail message arrives, “ buzzer or ring tone for Area Mail sounds. The received contents of some messages are automatically displayed. To erase the displayed content, select “OK”. You can receive Area Mail messages even when you are not contracted to use i-mode.
Phonebook Storing Phonebook Entries Storing New Phone Numbers/Mail Addresses, etc. Storing Phonebook Entries from Dial/ Received List 1 m( You can store Phonebook entries in the FOMA terminal (Phone) or on the docomo mini UIM card. 1 Zo (for at least one second)▶Phone Connect The display for entering a name appears. Enter a name and proceed. When storing entries onto the docomo mini UIM card Phonebook Select “UIM”. 2 Enter a reading. Enter a phone number. Enter a mail address. 3 46 Press c( ).
i-mode/Full Browser Displaying i-mode Sites i-mode is a service that enables you, by using the display of the mobile phone supporting i-mode, to use online services such as site access, Internet access, and i-mode mail. i-mode is a pay service that is available on a subscription basis. For details on i-mode, refer to “Mobile Phone User’s Guide [i-mode]”. You can display SSL/TLS※-compatible pages via FOMA terminal.
Displaying Websites Designed for PC You can browse Internet websites designed for PCs using the Full Browser function. Note that you are charged a high communication fee for the massive data communication such as browsing Internet websites having many images or downloading data. For details on the packet communication fee, refer to “Mobile Phone User’s Guide [i-mode]”. You can browse Internet websites composed of frames. You can select a frame to display it as well.
Storing Frequently Accessed Sites Bookmark websites or i-mode sites you frequently visit to get them displayed easily. i-Channel This service distributes information such as news and weather forecast to i-Channel mobile phones. The automatically received latest information flows on the m( ) while the site is displayed Stand-by display by tickers. You can read it on the i-Channel ▶Bookmark▶Add bookmark▶OK list by pressing *r.
Camera Shooting Still Images/Moving Pictures Viewing and Operation of Finder Display Shooting Still Images For Digicam mode ❶MENU You can check the settings. ❶ ❷Key operation guidance ❷ ❸Focus frame When a subject is focused on, the frame becomes green. ❸ ❹Zoom bar The zooming status is displayed.
Shooting Still Images Using Auto Timer Viewing Still Images/Moving Pictures after Shooting You can display the still image or the moving picture you have shot in Picture Album. You can detect a person’s face on the still image you have shot and expand it, or add corrective effects to the detected face. You can also play expressive slide shows with the effect function. 1 m▶Data box▶My picture or imotion/ Movie▶Picture album Picture Album is also activated by pressing l( from the Finder display.
※Channels might be reorganized along with the discontinuation of analog broadcasting. For this reason, you might need to reset the channels by using an Using 1Seg automatic scan (see page 53). After resetting the channels, be sure to register the channels to the channel list. For ■Using 1Seg details about channel changes accompanying terrestrial 1Seg is a service provided by television entrepreneurs digital broadcasting, check resources such as the (broadcasting stations).
Setting Channels Viewing and Operating Viewer Display When you activate 1Seg for the first time or change the area you are in, you need to operate “Channel setting”. Select “Auto channel setting” to enable you to search automatically for broadcast stations you can watch. You need to set this function when you are in a terrestrial ❶ digital TV broadcasting service area. 1 m▶CAMERA/TV/MUSIC▶1Seg ▶Channel setting▶Auto channel setting ❹ ❺ ❻ ❼ ❷ ▶YES▶YES▶Enter a title.
The operation on the viewer display Channel switch: No Sound volume adjustment: Bo Mute/Unmute: r Switch TV/data BC: l Video recording: Oo( )(for at least one second) or x (for at least one second) The recorded video is saved on the microSD card. Setting Timer Watching or Recording 1Seg Set the date and time, a channel, and program name, and enter them to the TV Timer List or Timer Recording List. When the set time arrives, you can start watching or recording.
Setting Programs 1 m▶CAMERA/TV/MUSIC ▶Music&Video Channel▶Program set. ▶Follow the instructions on the display to set a program. The program automatically downloads at night. Playing Programs 1 Playing Music Files m▶CAMERA/TV/MUSIC MUSIC Player enables you to play Chaku-uta Full® music files you have downloaded from sites, or to play Windows Media® Audio (WMA) files you saved on the microSD card using your personal computer. ▶Select a program.
i-αppli/i-Widget i-αppli is a software program for mobile phone supporting i-mode. By downloading various software programs from the i-mode site, you can use your FOMA terminal more conveniently. You can automatically update the stock price information or weather information, and enjoy games without accessing network. i-Widget is a useful function for gaining easy access to frequently used contents and tools (Widget Appli programs) such as the calculator, clock, memo pad and stock market information.
i-motion/Movie i-motion is a file consisting from video, audio, and music which you can download to your FOMA terminal from i-motion sites that support i-motion. You can also set it for a ring tone. Also, by using high speed communication, you can play back smooth and high-quality movie files provided by portal sites, movie specialty sites and other sites on the Internet. When downloading or streaming an i-motion/movie file, you might receive a bulky file.
More Convenient i-concier 58 i-concier works to serve you with a pleasant life just like a clerk or concierge does. The service holds your data (area information about your neighborhood, Memo, Schedule, ToruCa, Phonebook, etc.) and sends you information, with good timing, about a variety of things according to the contents of your memo and your schedule event, your living area, your current location, or your preference or taste.
Using Start by Voice You can call up the function by voice. This function is available in Japanese mode only. The first time you use this function, select “利用する (Use)” ). on the usage information display, or press c( 1 When the function to be called up cannot be specified, you can look it up in “使いかたガイド (Guide)”. ■Note when using Shabette-Kensaku or Start by Voice Speak as clearly as possible, in natural conversation speed. Speak in quiet, noise-free locations.
More Convenient Using Bar Code Reader 60 You can use the camera to scan QR codes and others, and store them as files. From the scanned data, you can make calls, compose i-mode mail messages, access Internet websites, and so on. ■When scanning with Bar Code Reader Guide frame Scan the code as large as possible within the guide frame. Autofocus works when you scan the code about 10 cm or more away from it. When you scan the code in the out-of-focus state, the recognition rate lowers.
Data Management Using microSD Card The inserting slot of the microSD card is in the inside of the back cover. To insert it, remove the back cover, and then remove the battery pack. 1 With the metal terminal surface facing downward, make sure that the cut edge is positioned at right and then insert. Push it until it clicks. When you remove the microSD card Push the microSD card until it stops and remove it. Note that the microSD card may pop out when you insert or remove it.
Icons on the Display Formatting microSD Card : A microSD card is inserted. When you use the microSD card for the first time, you need to format (initialize) it. Be sure to use P-01E for formatting. The microSD card formatted using other devices such as personal computers may not work properly. Note that formatting deletes all content on the microSD card. : Data is being read/written. (Do not remove the microSD card nor turn off the FOMA terminal.) : The microSD card is write-protected.
Copying Data to FOMA Terminal Backing up Data to microSD Card Copying a still image You can back up Phonebook entries, schedule events, mail messages, memos, bookmarks, and the settings on and information about your FOMA terminal collectively onto the microSD card. When restoring the backup data onto your FOMA terminal, they are collectively restored.
More Convenient Sending/Receiving Data by Infrared Communication Sending Data Set the receiving end terminal first, and then start sending data within 60 seconds. 1 Submenu of the data to be sent ▶Send Ir data▶YES Procedure for sending data might differ depending on the data.
Support Troubleshooting First of all, check to see if you need to update the software program and then update it if necessary. See page 68 for how to update software programs. When symptom persists even after you check the countermeasures for the problem you suffer, contact the “Repairs” counter listed on the back page of this manual or a repair counter specified by DOCOMO. The “Repairs” counter is available in Japanese only. Power source The FOMA terminal does not turn on.
Pressing keys is disabled. …Make sure Dial Lock is deactivated. (See page 35) …Make sure Keypad Lock is deactivated. (See page 36) …Make sure Side Key Guard is set to “OFF”. The docomo mini UIM card is not recognized. …Make sure you insert the docomo mini UIM card in the correct direction. (See page 19) The clock does not show the correct time. …The clock may not show the correct time when the power has been kept on for a prolonged period of time.
Do not peel the nameplate off the FOMA terminal. Note that when we cannot ensure the contents described on the nameplate and therefore cannot verify the product conformity to the technical standard, it might happen that we at DOCOMO reject to repair the malfunction. The information such as about function settings, etc. might be reset depending on the troubles or repairs, or the way you handle the FOMA terminal. Set the settings again.
Error Information Send Setting Others 1 68 Updating Software When an error occurs on the FOMA terminal, the error This function is to check whether you need to update information is created automatically and send it to DOCOMO software programs in the FOMA terminal by connecting to if this function is set to “ON”. the network, and if necessary, you can download some parts of software programs using packet communication, and can m▶Setting▶Other setting update the software programs.
You are advised to update software programs when radio wave is strong enough with the three antennas displayed and while you are not moving. If radio wave conditions get worse while downloading software programs, or download is suspended, move to a place with better radio wave conditions and try again to update software programs. When updating software programs, the proprietary information about your FOMA terminal (model name or serial number, etc.
Scanning Function You can detect data or application programs, which might cause troubles, from among those downloaded to your FOMA terminal, and then can delete the data or stop starting the application programs. This scan function provides a certain protective measure to filter out data that might cause troubles with your FOMA terminal at the time when you browse websites or receive messages.
Options and Related Devices Combining various options with the FOMA terminal, you can realize more versatile use from personal purpose to business purposes. Some products may not be dealt in depending on the area. For details, consult a handling counter such as a docomo Shop. For details on options, refer to the user’s manuals of respective options and related devices.
72 imode/web Inbox Outbox Draft Mail history box Compose new message Create new Deco-Anime Deco-mail DecomeTemplate Decome-Anime Compose new SMS Check mail/message Check new SMS Receive option Receive setting Display setting Text predict Signature setting Mail setting Phrases/Store word Mail box lock Set check mail/message Blog/Mail group iαppli Auto save setting SMS setting Mail setting Area Mail setting Auto Deco-mail setting Check settings Reset iMenu/Search Bookmark Screen Memo Browsing history Ente
My picture MUSIC Music&Video Channel imotion/Movie Melody Content package My document Kisekae Tool Machi-chara Chara-den Image 1Seg Video Position memory Document viewer Font Tool Bar code reader Scan code Saved data Receive Receive all Schedule Memo Data Security Service microSD Data check/Download Update phonebooks Update schedule etc.
Setting for videophone 74 Call forwarding Call waiting English guidance Remote access Multi Number Additional service Choku-Den Kisekae Tool setting Stand-by display MyFACE setting Color theme setting Each display setting Sub-display setting Machi-chara setting Screen/ Display Soft key Menu Theme Viewer settings Icons Icons setting View blind Image display mode LCD AI Mail ticker display Information display Setting TEL function Videophone Ntfy switch-mode setting Reject videophone Hands-free switch V
imadoco search Map/Overseas Overseas setting Missed call notice Roaming guidance Int’l dial assistance imode service set. i-concier Profile MultiOneTouch Character input imadoco kantan search imadoco search i-area Overseas NW search Network search setting PLMN setting Display operator name Display area status Re-search icon set. Others Map/Overseas Other setting Side key guard Camera-button setting Alarm setting Self mode Reset settings Initialize Software Update Error info send set.
Main Specifications ■Handset Model P-01E Dimensions (when closed) Height: Approx. 111 mm Width: Approx. 51 mm Depth: Approx. 15.9 mm Approx. 120 g Weight (with the battery pack attached) Continuous standby time (FOMA/3G) Continuous talk time (FOMA/3G) 1Seg watching time Charging time Display Type Size Others Number of pixels 76 Image pickup device Type Size Camera Number of effective pixels Number of recording pixels (maximum) Standstill: Approx. 610 hours Voice call : Approx.
■Battery pack Name of product Battery type Voltage Battery Pack P23 Li-ion (lithium ion) battery 3.7 V 800 mAh Capacity ■Specifications of shooting File format (Extension) JPEG (jpg) The number of files that can be Approx. 1,300 max. ※1※2 saved to P-01E The number of files that can be Approx. 30,733 max.
The actual SAR of this mobile phone while operating can be well below that indicated above. This is due to automatic changes to the power level of the device to ensure it only uses SAR Certification the minimum required to reach the network. Therefore in general, the closer you are to a Information base station, the lower the power output of This model P-01E mobile phone complies the device.
European RF Exposure Information This mobile phone complies with the EU requirements for exposure to radio waves. Your mobile phone is a radio transceiver, designed and manufactured not to exceed the SAR* limits** for exposure to radio-frequency (RF) energy, which SAR* value, when tested for compliance against the standard were 0.822 W/kg for head configuration and 0.307 W/kg for body worn configuration.
Others 80 The SAR limit set by the FCC is 1.6 W/kg.* Tests for SAR are conducted using standard operating positions accepted by the FCC with the phone transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value.
Export Administration Regulations This product and its accessories might be covered by the Japan Export Administration Regulations (“Foreign Exchange and Foreign Trade Law” and its related laws). To export this product and its accessories, take the required measures on your responsibility and at your expenses. For details on the procedures, contact the Ministry of Economy, Trade and Industry.
Others Powered by Mascot Capsule®/Micro3D Edition™ Mascot Capsule® is a trademark of HI CORPORATION. “Blu-ray Disc” and “Blu-ray” are trademarks of the Blu-ray Disc Association. 82 This product contains software licensed complying with GNU General Public License, Version 2 (GPL v2), GNU Lesser General Public License (LGPL), etc. The program is free software; you can copy it and/or redistribute it and/or modify it under the terms of the GPL v2 or LGPL as published by the Free Software Foundation.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: - Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. - Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Others Index Line feed ...........................................29 Pictograms........................................29 Smiley ...............................................29 Symbols ............................................29 Character size......................................32 Charging ..............................................20 Charging terminal ..................................3 Check mail/message ...........................44 Command navigation key ...................
i-mode mail ..........................................43 Compose ..........................................43 Forward .............................................44 Receive .............................................44 Reply .................................................44 Send..................................................43 i-mode password.................................34 i-motion ................................................57 Infrared communication ......................
Others Receiving a videophone call ...............38 Record message .................................38 Related devices ...................................71 Reset settings ......................................36 Ring volume .........................................30 86 Start by voice.......................................59 Numerics Status icon ...........................................22 1Seg .....................................................52 Strap hole .........................................
Access the following for checking or changing the contents of your contract, or for applying to respective services, and asking for related documents: From i-mode ｉMenu ▶ お客様サポート (User support) ▶ お申込・お手続き (Applications/Procedures) ▶ 各種お申込・お手続き (Respective applications/procedures) Packet communication charges free From PC My docomo (http://www.mydocomo.com/) ▶ 各種お申込・お手続き “お客様サポート (User support)” and My docomo are available in Japanese only.
Loss or theft of FOMA terminal or payment of cumulative cost overseas (available 24 hours a day) ■ From DOCOMO mobile phones International call access code for the country you stay at -81-3-6832-6600* (toll free) Failures encountered overseas (available 24 hours a day) ■ From DOCOMO mobile phones International call access code for the country you stay at -81-3-6718-1414* (toll free) * You are charged a call fee to Japan when calling
General Inquiries Repairs 0120-005-250 ■ From DOCOMO mobile phones ■ From land-line phones (toll free) * Service available in English, Portuguese, Chinese, Spanish, and Korean. * Unavailable from part of IP phones. (Business hours: 9:00 a.m. to 8:00 p.m.) ■ From DOCOMO mobile phones ■ From land-line phones (In Japanese only) (No prefix) 151 (toll free) * Unavailable from land-line phones, etc.
