PAN1770 Bluetooth® Low Energy Module Product Specification Rev. 1.
PAN1770 Bluetooth Module Overview The PAN1770 is a Bluetooth 5.3 Low Energy (LE) module based on the Nordic nRF52840 single chip controller. Features • Surface mount type dimensions: 15.6 mm × 8.7 mm × 2.05 mm • • • • Same form factor as PAN1026A and PAN1762 but smaller pitch and more pins U.FL connector for external antenna Nordic nRF52840 featuring with 64 MHz ARM® Cortex®-M4F Bluetooth 5.
PAN1770 Bluetooth Module By purchase of any of the products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic Industrial Devices Europe GmbH (Panasonic) reserves the right to make changes as required at any time without notification. Please consult the most recently issued Product Specification before initiating or completing a design. © Panasonic Industrial Devices Europe GmbH 2022.
PAN1770 Bluetooth Module Product Change Notifications (PCNs) and Information Notes (INs) Please consider the following PCNs/INs and take suitable countermeasures where necessary and appropriate; for further details please contact your local Panasonic Sales office ( 7.2.1 Contact Us): • • • Nordic APPROTECT vulnerability problem description: IN133 Informational Notice v1.0 Nordic APPROTECT solution description: IN141 Informational Notice v1.
PAN1770 Bluetooth Module Table of Contents 1 2 3 About This Document......................................................................................................................... 7 1.1 Purpose and Audience .............................................................................................................. 7 1.2 Revision History ......................................................................................................................... 7 1.3 Use of Symbols .........
PAN1770 Bluetooth Module 6 Regulatory and Certification Information ....................................................................................... 31 6.1 For Bluetooth Low Energy ....................................................................................................... 31 6.1.1 General Certification Information ................................................................................................31 6.1.2 Federal Communications Commission (FCC) for US ....................
PAN1770 Bluetooth Module 1 About This Document 1 About This Document 1.1 Purpose and Audience This Product Specification provides details on the functional, operational, and electrical characteristics of the Panasonic PAN1770 module. It is intended for hardware design, application, and Original Equipment Manufacturers (OEM) engineers. The product is referred to as “the PAN1770” or “the module” within this document. 1.2 Revision History Revision Date Modifications/Remarks 1.
PAN1770 Bluetooth Module 1 About This Document Symbol Description Menu > Menu item Path Indicates a path, e.g. to access a dialog. Example: In the menu, select File > Setup page. This font Messages, user input, code Indicates messages, information, and code displayed on the screen or to be entered by the user. Examples: The message Failed to save your data is displayed. Enter the value Product 123. Copy firmware binaries to firmware library: $> cd ${TOP}/… $> … 1.
PAN1770 Bluetooth Module 2 Overview 2 Overview The PAN1770 is a Bluetooth 5.3 Low Energy (LE) module based on the Nordic nRF52840 single-chip controller. The Bluetooth 5.3 features additionally a higher symbol rate of 2 Mbps using the high-speed LE 2M PHY or a significantly longer range using the LE coded PHY at 500 kb/s or 125 kb/s. The new channel selection algorithm (CSA#2) improves the performance in high interference environments.
PAN1770 Bluetooth Module 2.1 2 Overview Block Diagram Product Specification Rev. 1.
PAN1770 Bluetooth Module 2.2 2 Overview Pin Configuration Pin Assignment Top View G1 G2 G3 G4 G5 G6 G7 G8 G9 G10 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 E1 E2 E3 E4 E5 E6 E7 E8 E9 E10 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 G12 G13 A12 A13 Pin Functions No. Pin Name Pin Type Description A1 P0.27 Digital BI GPIO A2 P0.26 Digital BI GPIO A3 P0.
PAN1770 Bluetooth Module No. Pin Name 2 Overview Pin Type Description B4 P0.31/AIN7 Digital BI/Analog Input GPIO/Sensor to ADC B5 P0.28/AIN4 Digital BI/Analog Input GPIO/Sensor to ADC B6 P1.13 Digital BI GPIO B7 P1.10 Digital BI GPIO B8 P1.06 Digital BI GPIO B9 P1.15 Digital BI GPIO Ground Connect to ground C1 P0.08 Digital BI GPIO C2 X32k_IN 32 kHz Leave open C3 P1.03 Digital BI GPIO C4 GND Ground Connect to ground C5 GND Ground Connect to ground C6 P1.
PAN1770 Bluetooth Module No. Pin Name 2 Overview Pin Type Description E7 P0.21 Digital BI GPIO E8 SWDCLK Digital BI Serial Wire Debug IF Clock E9 P1.04 Digital BI GPIO E10 NC Leave open F1 P0.12/TRCDAT1 Digital BI GPIO or Trace IF D1 F2 P0.11/TRCDAT2 Digital BI GPIO or Trace IF D2 F3 P0.13 Digital BI GPIO F4 P0.14 Digital BI GPIO F5 P0.15 Digital BI GPIO F6 P0.19 Digital BI GPIO F7 P1.01 Digital BI GPIO F8 P0.25 Digital BI GPIO F9 P0.
PAN1770 Bluetooth Module 2.3 Peripherals • • • • • • • • • • • • • • • 2.4 2 Overview Full-speed USB 2.0 device controller 2× UART (2× or 4× wire with CTS/RTS, 1 200 up to 1 M baud) I2C, I2S, SPI (32 MHz) QSPI (32 MHz) PWM PDM AES and CryptoCell 8× channel 12 bit ADC Comparator Quadrature decoder Temperature sensor Real time counter Watchdog timer 48× PIOs Integrated 32 kHz crystal Bluetooth Features • • Bluetooth LE 5.3 Supports Bluetooth LE 5.
PAN1770 Bluetooth Module 3 Detailed Description 3 Detailed Description 3.1 Dimensions All dimensions are in millimeters. Top View 2.00 mm 2.05 mm 8.70 mm 15.60 mm No. Item Dimension Tolerance Remark 1 Width 8.70 ±0.30 2 Length 15.60 ±0.30 3 Height 2.05 Product Specification Rev. 1.0 ±0.30 With U.
PAN1770 Bluetooth Module 3.2 3 Detailed Description Footprint All dimensions are in millimeters. G2 G3 G4 G5 G6 G7 G8 G9 G10 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 E1 E2 E3 E4 E5 E6 E7 E8 E9 E10 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 G12 G13 A12 A13 1.10 G1 1.05 8.70 1.05 Top View 1.00 1.10 0.60 2.20 1.40 15.60 Product Specification Rev. 1.
PAN1770 Bluetooth Module 3.3 3 Detailed Description Packaging The module is a mass production status product and will be delivered in the package described below. 3.3.1 Tape Dimensions 3.3.2 Packing in Tape Direction of unreeling (for customer) trailer (empty) 1 x circumference / hub (min 160mm) component packed area standard 1500pcs leader (empty) minimum 10 pitch Top cover tape more than 1 x circumference plus 100mm to avoid fixing of tape end on sealed modules.
PAN1770 Bluetooth Module 3.3.3 3 Detailed Description Component Direction Pin 1 Marking (Top Side) Direction of unreeling (for customer) 3.3.4 Reel Dimension Product Specification Rev. 1.
PAN1770 Bluetooth Module 3.3.5 3 Detailed Description Package Label Example: 3.3.6 (1T) Lot code (1P) Customer order number, if applicable (2P) Order number (9D) Date code (Q) Quantity (HW/SW) Hardware/software version Total Package Product Specification Rev. 1.
PAN1770 Bluetooth Module 3.4 3 Detailed Description Case Marking Example: 1 Brand name 2 Hardware/software version 3 Order number 4 Lot code 5 Status: ES or empty for MP 6 2D barcode, for internal usage only 7 Marking for Pin 1 8 Bluetooth logo Product Specification Rev. 1.
PAN1770 Bluetooth Module 4 Specification 4 Specification All specifications are over temperature and process, unless indicated otherwise. 4.1 Default Test Conditions Temperature: Humidity: Supply Voltage: 4.2 25 °C ± 10 °C 40 % to 85 % RH 3.3 V Absolute Maximum Ratings The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. Symbol Parameter VDD Normal Supply Voltage -0.3 +3.
PAN1770 Bluetooth Module 4.3 4 Specification Recommended Operating Conditions The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. Symbol Parameter VDD (LV Mode) Supply Voltage tR_ VDD Supply Rise Time 0 V to 1.7 V VDD-POR Supply Voltage Power On Reset active VDDH (HV Mode) Supply Voltage VDDH - Optional tR_VDDH Supply Rise Time 0 V to 3.
PAN1770 Bluetooth Module 4.5 4 Specification Parameter Condition Min. Typ. Max. Unit Tx Current 8 dBm 14.8 mA 4 dBm 9.6 mA 0 dBm 4.8 mA -4 dBm 3.1 mA -8 dBm 3.3 mA -12 dBm 3.0 mA -16 dBm 3.8 mA -20 dBm 2.7 mA -40 dBm 2.
PAN1770 Bluetooth Module 4 Specification Locking the Device Debug Port and enabling the Access Port Protection Once the access port protection is enabled, no further access including debugging can be done anymore! Please make sure to use the described (or later) software version. To ensure that the device debug port is locked during production programming and the access port protection is enabled correctly, the following steps must be followed. 1.
PAN1770 Bluetooth Module 4 Specification For technical details please refer to IN141 Informational Notice v1.1 in the Nordic Infocenter https://infocenter.nordicsemi.com/. 4.7 Antenna Placement Recommendation Impact of Placement on the Antenna Radiation Pattern The placement of the antenna, surrounding material, and customer components has an impact on his radiation pattern. It is recommended to use the antenna and “U.FL to Reverse Polarity SMA” adapter cable listed in 6.1.2.
PAN1770 Bluetooth Module 4.9 4 Specification Recommended Soldering Profile • • • • • Reflow permissible cycles: 2 Opposite side reflow is prohibited due to module weight More than 75 percent of the soldering area shall be coated by solder The soldering profiles should be adhered to in order to prevent electrical or mechanical damage Soldering profile assumes lead-free soldering Product Specification Rev. 1.
PAN1770 Bluetooth Module 5 Cautions 5 Cautions Failure to follow the guidelines set forth in this document may result in degrading of the module functions and damage to the module. 5.1 Design Notes 1. Follow the conditions written in this specification, especially the control signals of this module. 2. The supply voltage should abide by the maximum ratings ( 4.2 Absolute Maximum Ratings). 3.
PAN1770 Bluetooth Module 5.3 5 Cautions Usage Condition Notes 1. Take measures to protect the module against static electricity. If pulses or transient loads (a large load, which is suddenly applied) are applied to the modules, check and evaluate their operation before assembly of the final products. 2. Do not use dropped modules. 3. Do not touch, damage, or soil the pins. 4. Follow the recommended condition ratings about the power supply applied to this module. 5.
PAN1770 Bluetooth Module 5 Cautions 1. Ensure the safety of the whole system by installing a protection circuit and a protection device. 2. Ensure the safety of the whole system by installing a redundant circuit or another system to prevent a single fault causing an unsafe status. 5.6 Other Cautions 1. Do not use the module for other purposes than those listed in 5.3 Usage Condition Notes. 2.
PAN1770 Bluetooth Module 5.7 5.7.
PAN1770 Bluetooth Module 6 Regulatory and Certification Information 6 Regulatory and Certification Information 6.1 6.1.1 For Bluetooth Low Energy General Certification Information Regulatory certifications are valid for the following radio relevant software: • • • Nordic SoftDevice S140, S113, and Wirepas V4.x or V5.x nRF Connect SDK (NCS) Bluetooth Specification 5.
PAN1770 Bluetooth Module 6 Regulatory and Certification Information The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407. The transmitter operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. 6.1.2.
PAN1770 Bluetooth Module 6.1.2.3 6 Regulatory and Certification Information Label Requirements The OEM must ensure that FCC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic FCC identifier for this product as well as the FCC Notice above. The FCC identifier is FCC ID: T7V1780. This FCC identifier is valid for the PAN1770.
PAN1770 Bluetooth Module 6.1.2.6 6 Regulatory and Certification Information RF Exposure To comply with FCC RF Exposure requirements, the OEM must ensure that only antennas from the Approved Antenna List are installed 6.1.2.5 Approved Antenna List. The preceding statement must be included as a “CAUTION” statement in manuals for products operating with the approved antennas in the previous table to alert users on FCC RF Exposure compliance.
PAN1770 Bluetooth Module 6 Regulatory and Certification Information The end customer has to assure that the device has a distance of more than 15 mm from the human body under all circumstances. If the end customer application intends to use the PAN1770 in a distance smaller 15 mm from the human body, SAR evaluation has to be repeated by the OEM. The end customer equipment must meet the actual Safety/Health requirements according to ISED.
PAN1770 Bluetooth Module 6.1.3.1 6 Regulatory and Certification Information IC Notice English The device PAN1770 ( 7.1 Ordering Information), including the antennas ( 6.1.2.5 Approved Antenna List), complies with Canada RSS-GEN Rules. The device meets the requirements for modular transmitter approval as detailed in RSS-Gen. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
PAN1770 Bluetooth Module 6.1.3.2 6 Regulatory and Certification Information Labeling Requirements English Labeling Requirements The OEM must ensure that IC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic IC identifier for this product as well as the IC Notice above. The IC identifier is IC: 216Q-1780. This IC identifier is valid for all PAN1770 modules 7.1 Ordering Information.
PAN1770 Bluetooth Module 6.1.4 6 Regulatory and Certification Information European Conformity According to RED (2014/53/EU) All modules described in this Product Specification comply with the standards according to the following LVD (2014/35/EU), EMC-D (2014/30/EU) together with RED (2014/53/EU) articles: 3.1a Safety/Health: EN 62368-1: 2014/AC: 2015/A11: 2017 EN 62479: 2010 3.1b EMC: EN 301 489-1 V2.2.3: (2019-11) EN 301 489-17 V3.2.2: (2019-02) 3.2 Radio: • • EN 300 328 V2.2.
PAN1770 Bluetooth Module 6.1.5 6 Regulatory and Certification Information United Kingdom Conformity According to Statutory Instrument SI 2017/1206 All modules described in this Product Specification comply with the designated standards according to the following Regulations: Electrical Equipment (Safety) SI 2016/1101, EMC SI 2016/1091 together with Radio Equipment Regulation 2017 (RER) SI 2017/1206: Safety/Health: EN 62368-1: 2014/AC: 2015/A11: 2017 EN 62479: 2010 EMC: EN 301 489-1 V2.2.
PAN1770 Bluetooth Module 6.1.6 6 Regulatory and Certification Information Bluetooth The final Bluetooth end product listing needs to be created by using the following IDs: Bluetooth 5.1 Declaration ID QDID End product D050150 148922 Bluetooth 5.
PAN1770 Bluetooth Module 6 Regulatory and Certification Information Regulatory certifications stay valid for APPROTECT versions provided that: If the nRF52840 new silicon revision 3 with access port protection, which is implemented in the PAN1770 with Panasonic order number ENW89854C2KF is used: • Nordic IN141 Informational Notice v1.1 states “The new revision has no impact on CE, FCC/ISED or Bluetooth certifications unless the new pulse shaping filter is enabled.
PAN1770 Bluetooth Module 6 Regulatory and Certification Information The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407. The transmitter operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. 6.2.2.
PAN1770 Bluetooth Module 6 Regulatory and Certification Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAN1770 Bluetooth Module 6 Regulatory and Certification Information The device is tested with a “U.FL to Reverse Polarity SMA” adapter cable and with the antenna listed below. When integrated into the OEM’s product, these fixed antennas require installation preventing end users from replacing them with non-approved antennas. Any antenna not in the following table must be tested to comply with FCC Section 15.203 for unique antenna connectors and with Section 15.247 for emissions.
PAN1770 Bluetooth Module 6 Regulatory and Certification Information Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and ensure compliance for SAR and/or RF exposure limits. Users can obtain Canadian information on RF exposure and compliance from www.ic.gc.ca. This device has been designed to operate with the antennas listed in 6.1.2.5 Approved Antenna List, having a maximum gain of +1.4 dBi.
PAN1770 Bluetooth Module 6 Regulatory and Certification Information Le client final doit s'assurer que l'appareil se trouve en toutes circonstances à une distance de plus de 15 mm du corps humain. Si le client final envisage une application nécessitant d'utiliser le PAN1770 à une distance inférieure à 15 mm du corps humain, alors le FEO doit répéter l'évaluation DAS. L'équipement du client final doit répondre aux exigences actuelles de sécurité et de santé selon l’ISED. 6.2.3.
PAN1770 Bluetooth Module 6.2.3.2 6 Regulatory and Certification Information Labeling Requirements English Labeling Requirements The OEM must ensure that IC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic IC identifier for this product as well as the IC Notice above. The IC identifier is IC: 216Q-1780. This IC identifier is valid for all PAN1770 modules 7.1 Ordering Information.
PAN1770 Bluetooth Module 6.2.4 6 Regulatory and Certification Information European Conformity According to RED (2014/53/EU) All modules described in this Product Specification comply with the standards according to the following LVD (2014/35/EU), EMC-D (2014/30/EU) together with RED (2014/53/EU) articles: 3.1a Safety/Health: EN 62368-1: 2014/AC: 2015/A11: 2017 EN 62479: 2010 3.1b EMC: EN 301 489-1 V2.2.3: (2019-11) EN 301 489-17 V3.2.2: (2019-02) 3.2 Radio: • • EN 300 328 V2.2.
PAN1770 Bluetooth Module 6.2.5 6 Regulatory and Certification Information United Kingdom Conformity According to Statutory Instrument SI 2017/1206 All modules described in this Product Specification comply with the designated standards according to the following Regulations: Electrical Equipment (Safety) SI 2016/1101, EMC SI 2016/1091 together with Radio Equipment Regulation 2017 (RER) SI 2017/1206: Safety/Health: EN 62368-1: 2014/AC: 2015/A11: 2017 EN 62479: 2010 EMC: EN 301 489-1 V2.2.
PAN1770 Bluetooth Module 6 Regulatory and Certification Information supplied products can be found on the Panasonic website in the “Downloads” section of the respective product 7.2.2 Product Information. Product Specification Rev. 1.
PAN1770 Bluetooth Module 7 Appendix 7 Appendix 7.1 Ordering Information Variants and Versions MOQ1 Order Number Brand Name Description ENW89854C1KF 2 PAN1770 Bluetooth Low Energy Single Mode with U.FL connector 1 500 Empty Flash ENW89854C2KF 2 PAN1770 Bluetooth Low Energy Single Mode with U.FL connector 1 500 Access Port Protection APPROTECT HW Empty Flash 1 Abbreviation for Minimum Order Quantity (MOQ). The default MOQ for mass production is 1 500 pieces, fewer only on customer demand.
PAN1770 Bluetooth Module 7.2 7.2.1 7 Appendix Contact Details Contact Us Please contact your local Panasonic Sales office for details on additional product options and services: For Panasonic Sales assistance in the EU, visit https://eu.industrial.panasonic.com/about-us/contact-us Email: wireless@eu.panasonic.com For Panasonic Sales assistance in North America, visit the Panasonic website “Sales & Support” to find assistance near you at https://na.industrial.panasonic.
