PAN1760A Bluetooth Low Energy Module Product Specification Rev. 1.
PAN1760A Bluetooth Module Overview The PAN1760A is Panasonic’s next generation Bluetooth module with the industry’s lowest power Bluetooth Low Energy SoC. Features • Small 15.6 mm x 8.7 mm x 1.9 mm SMD module • Same form factor and pinout as PAN1026, PAN1760, and PAN1761 • • • • • • • Bluetooth Low Energy 4.
PAN1760A Bluetooth Module By purchase of any of the products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic reserves the right to make changes as required at any time without notification. Please consult the most recently issued Product Specification before initiating or completing a design. © Panasonic Industrial Devices Europe GmbH 2017. This specification sheet is copyrighted.
PAN1760A Bluetooth Module Table of Contents 1 2 3 4 5 6 7 About This Document......................................................................................................................... 5 1.1 Purpose and Audience .............................................................................................................. 5 1.2 Revision History ......................................................................................................................... 5 1.
PAN1760A Bluetooth Module 1 About This Document 1 About This Document 1.1 Purpose and Audience This Product Specification provides details on the functional, operational, and electrical characteristics of the Panasonic PAN1760A module. It is intended for hardware design, application, and Original Equipment Manufacturers (OEM) engineers. The product is referred to as “the PAN1760A” or “the module” within this document. 1.2 1.3 Revision History Revision Date Modifications/Remarks 0.1 23.05.
PAN1760A Bluetooth Module 2 Overview 2 Overview The PAN1760A is Panasonic’s next generation Bluetooth module with the industry’s lowest power Bluetooth Low Energy SoC. The module is based on Toshiba's single chip TC35678 Bluetooth semiconductor device with embedded Toshiba Bluetooth 4.2 LE stack and embedded flash for the user application in stand-alone operation. Peak power consumption of only 3.
PAN1760A Bluetooth Module 2 Overview 2.1 Block Diagram PAN1760A Bluetooth 4.2 Module Vcc 3.3 V Slow Clock 32 KHz UART Crystal 26 MHz GPIOs Chip Antenna SWD Host Wake up Toshiba TC35678 DC-DC Conversion Wake up Flash 256 kB Reset Total capacitor value: 2.4 µF +/-10 % Total inductance: 10 µH +/-10 % Total resistance: 100 KΩ +/-10 % Product Specification Rev. 1.
PAN1760A Bluetooth Module 2 Overview 2.2 Pin Configuration Pin Assignment Top View 15.6 mm 5.0 1.2 2.4 F2 F3 F4 F5 F6 F7 F8 F9 E1 E2 E3 E4 E5 E6 E7 E8 E9 D1 D2 D3 D4 D5 D6 D7 D8 D9 C1 C2 C3 C4 C5 C6 C7 C8 C9 B1 B2 B3 B4 B5 B6 B7 B8 B9 A1 A2 A3 A4 A5 A6 A7 A8 A9 F11 F12 A11 A12 1.35 1.2 F1 8.70 mm 0.6 1.35 1.0 0.
PAN1760A Bluetooth Module 2 Overview No Pin Name Pin Type Description B3 NC NC Not connected, leave open B4 NC NC Not connected, leave open B5 GPIO7 Digital I/O B6 GPIO8 Digital I/O B7 GPIO25 Digital I/O B8 NC NC Not connected, leave open B9 NC NC Not connected, leave open C1 NC NC Not connected, leave open C2 NC NC Not connected, leave open C3 GPIO10 Digital I/O C4 SWDIO JTAG C5 SWDCLK JTAG C6 GPIO1 Digital I/O C7 NC NC Not connected, leave open C8
PAN1760A Bluetooth Module 2 Overview No Pin Name Pin Type Description E7 NC NC Not connected, leave open E8 GND Ground Pin Connect to ground E9 GND Ground Pin Connect to ground F1 GND Ground Pin Connect to ground F2 NC NC Not connected, leave open F3 NC NC Not connected, leave open F4 NC NC Not connected, leave open F5 GPIO14/UARTCTS Digital Input UART CTS F6 GPIO2 Digital I/O F7 GPIO5/UARTTXD Digital Output UART TX F8 GPIO13/UARTRTS Digital Output UART RTS
PAN1760A Bluetooth Module 3 Detailed Description 3 Detailed Description 3.1 Dimensions All dimensions are in millimeters. No. Item Dimension Tolerance Remark 1 Width 8.70 ± 0.20 2 Length 15.60 ± 0.20 3 Height 1.80 Product Specification Rev. 1.0 ± 0.
PAN1760A Bluetooth Module 3 Detailed Description 3.2 Footprint The outer dimensions have a tolerance of 0.2 mm. Top View 15.6 mm 5.0 1.2 2.4 F2 F3 F4 F5 F6 F7 F8 F9 E1 E2 E3 E4 E5 E6 E7 E8 E9 D1 D2 D3 D4 D5 D6 D7 D8 D9 C1 C2 C3 C4 C5 C6 C7 C8 C9 B1 B2 B3 B4 B5 B6 B7 B8 B9 A1 A2 A3 A4 A5 A6 A7 A8 A9 F11 F12 A11 A12 1.35 1.2 F1 8.70 mm 0.6 1.35 1.0 0.6 Product Specification Rev. 1.
PAN1760A Bluetooth Module 3 Detailed Description 3.3 Packaging The product is a mass production status product and will be delivered in the package described below. 3.3.1 Tape Dimensions 3.3.2 Packing in Tape Direction of unreeling (for customer) trailer (empty) 1 x circumference / hub (min 160mm) component packed area standard 1500pcs leader (empty) minimum 10 pitch Top cover tape more than 1 x circumference plus 100mm to avoid fixing of tape end on sealed modules.
PAN1760A Bluetooth Module 3 Detailed Description 3.3.3 Component Direction 3.3.4 Reel Dimension Product Specification Rev. 1.
PAN1760A Bluetooth Module 3 Detailed Description 3.3.5 Package Label Example (1T) (1P) (2P) (9D) (Q) (HW/SW) 3.3.6 Lot code Customer order number, if applicable Order number Date code Quantity Hardware/software version Total Package Product Specification Rev. 1.
PAN1760A Bluetooth Module 3 Detailed Description 3.4 Case Marking Example 1 2 3 4 5 6 7 8 9 Product Specification Rev. 1.
PAN1760A Bluetooth Module 4 Specification 4 Specification All specifications are over temperature and process, unless indicated otherwise. 4.1 Default Test Conditions Temperature: Humidity: Supply Voltage: 4.2 25 ± 10 °C 40 to 85 % RH 3.3 V Absolute Maximum Ratings The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result.
PAN1760A Bluetooth Module 4 Specification 4.3 Recommended Operating Conditions The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. 4.4 Symbol Parameter Condition Min. Typ. TA Ambient operating temperature range -40 VDD 3V3 Supply voltage 1.8 Max. Units +85 °C 3.6 V 3.3 Current Consumption The current consumption depends on the user scenario and on the setup and timing in the power modes.
PAN1760A Bluetooth Module 4 Specification 4.5 Bluetooth Parameter Condition Min. Operation frequency range Channel spacing Typ. 2 402 2 480 BLE Output Power Maximum setting, measured at dual ended 50 Ohm. Sensitivity 4.6 Max. Symbol Parameter Condition 1 Spurious emissions Conducted measurement with a 50 Ω dual-ended load. Complies with EN 300 328, EN 300 440 class 2, FCC CFR47, Part 15 and ARIB STD-T-66. Min. Units MHz 2 MHz 0 dBm -93 dBm Typ. Max.
PAN1760A Bluetooth Module 4 Specification 4.7 Recommended Soldering Profile • • • • Reflow permissible cycle: 2 • Soldering profile assumes lead-free soldering Opposite side reflow is prohibited due to module weight More than 75 percent of the soldering area shall be coated by solder The soldering profiles should be adhered to in order to prevent electrical or mechanical damage Product Specification Rev. 1.
PAN1760A Bluetooth Module 5 Cautions 5 Cautions Failure to follow the guidelines set forth in this document may result in degrading of the product’s functions and damage to the product. 5.1 Design Notes 1. Follow the conditions written in this specification, especially the control signals of this module. 2. The supply voltage must be free of AC ripple voltage (for example from a battery or a low noise regulator output).
PAN1760A Bluetooth Module 5 Cautions 5.3 Usage Condition Notes 1. Take measures to protect the unit against static electricity. If pulses or other transient loads (a large load applied in a short time) are applied to the products, check and evaluate their operation befor assembly on the final products. 2. Do not use dropped products. 3. Do not touch, damage or soil the pins. 4. Follow the recommended condition ratings about the power supply applied to this product. 5.
PAN1760A Bluetooth Module 5 Cautions 1. Ensure the safety of the whole system by installing a protection circuit and a protection device. 2. Ensure the safety of the whole system by installing a redundant circuit or another system to prevent a single fault causing an unsafe status. 5.6 Other Cautions 1. Do not use the products for other purposes than those listed. 2.
PAN1760A Bluetooth Module 6 Regulatory and Certification Information 6 Regulatory and Certification Information 6.1 6.1.1 Federal Communications Commission (FCC) for US FCC Notice The PAN1760A including the antennas, which are listed in 6.1.5 Approved Antenna List, complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407. The transmitter operation is subject to the following two conditions: 1.
PAN1760A Bluetooth Module 6 Regulatory and Certification Information 6.1.3 Label Requirements The OEM must ensure that FCC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic FCC identifier for this product as well as the FCC Notice above. The FCC identifier is FCC ID: T7V1760A. This FCC identifier is valid for the PAN1760A.
PAN1760A Bluetooth Module 6 Regulatory and Certification Information 6.1.6 RF Exposure To comply with FCC RF Exposure requirements, the OEM must ensure that only antennas from the Approved Antenna List are installed 6.1.5 Approved Antenna List. The preceding statement must be included as a CAUTION statement in manuals for products operating with the approved antennas in the previous table to alert users on FCC RF Exposure compliance.
PAN1760A Bluetooth Module 6 Regulatory and Certification Information French PAN1760A est garanti conforme aux dispositions règlementaires d’Industry Canada (IC). License: IC: 216Q-1760A Il est recommandé aux fabricants d’appareils fixes, mobiles ou portables de consulter la réglementation en vigueur et de vérifier la conformité de leurs produits relativement aux limites d’exposition aux rayonnements radiofréquence ainsi qu’au débit d’absorption spécifique maximum autorisé.
PAN1760A Bluetooth Module 6 Regulatory and Certification Information 6.2.2 Labeling Requirements English Labeling Requirements The OEM must ensure that IC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic IC identifier for this product as well as the IC Notice above. The IC identifier is: IC: 216Q-1760A This IC identifier is valid for all PAN1760A modules 7.1 Ordering Information.
PAN1760A Bluetooth Module 6 Regulatory and Certification Information 6.3 European Conformity According to RED (2014/53/EU) All modules described in this Product Specification comply with the standards according to the following LVD (2014/35/EU), EMC-D (2014/30/EU) together with the RED (2014/53/EU) articles: 3.1a Safety/Health: EN62368-1:2014 EN62311:2008 3.1b EMC: EN 301 489-1 V2.1.1:2017-02 EN 301 489-17 V3.1.1:2017-02 3.2 Radio: EN 300 328 V2.1.
PAN1760A Bluetooth Module 7 Appendix 7 Appendix 7.1 Ordering Information Variants and Versions Order Number 2 ENW89847A3KF Brand Name Description PAN1760A Bluetooth Low Energy Module 1 MOQ 1 500 1 Abbreviation for Minimum Order Quantity (MOQ). The default MOQ for mass production is 1 500 pieces, fewer only on customer demand. Samples for evaluation can be delivered at any quantity via the distribution channels. 2 Samples are available on customer demand. Product Specification Rev. 1.
PAN1760A Bluetooth Module 7 Appendix 7.2 7.2.1 Contact Details Contact Us Please contact your local Panasonic Sales office for details on additional product options and services: For Panasonic Sales assistance in the EU, visit https://eu.industrial.panasonic.com/about-us/contact-us Email: wireless@eu.panasonic.com For Panasonic Sales assistance in North America, visit the Panasonic Sales & Support Tool to find assistance near you at https://na.industrial.panasonic.
