Advanced Disc for Archive Drive LKM-KB12 INSTRUCTION MANUAL Please read through these instructions before operating this unit.
ENGLISH Advanced Disc for Archive Drive LKM-KB12 INSTRUCTION MANUAL Please read through these instructions before operating this unit. Interface : USB TABLE OF CONTENTS IMPORTANT SAFETY NOTICE ................................................................................ LASER SAFETY INFORMATION ............................................................................. 1. INTRODUCTION .................................................................................................... 1.
IMPORTANT SAFETY NOTICE NOTICE (1) You may not reproduce or transcribe any part of this publication without permission. (2) We reserve the right to revise this document at any time without notice. (3) If you have any questions about this document, contact your sales representative. SAFETY NOTICE (1) To prevent fire or electric shock, do not expose this appliance to rain or moisture. (2) To avoid electric shock or damage to the eyes due to laser beam, do not attempt to disassemble the cabinet.
IMPORTANT SAFETY INSTRUCTIONS 5. 6. 7. 8. 9. 10. 11. 12. 13. Read all of these instructions. Save these instructions for later use. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Do not use this product near water. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.
Class 1 LASER Product This equipment is certified to comply with DHHS Rule 21 CFR Chapter 1, Subchapter J in effect as of date of manufacture. Elsewhere, the drive is certified to conform to the requirements of the International Electrotechnical Commission (IEC) 60825-1 and CENELEC EN60825-1 for Class 1 laser products. Class 1 laser products are not considered to be hazardous. To ensure continued product safety, the following precautions should be heeded.
for BD media LASER Specification Type: Semiconductor laser InGaN Wave Length: 400 nm ~ 410 nm (Typical 405 nm) θ = 16 ° ~ 24 ° (Typical 20 °) Divergence: Output Power: Read = 0.53 mW Write = 19.
For Swedish VARNING! Om apparaten används på annat sätt än i denna bruksanvisning specificerats, kan användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1. ELECTROSTATIC DISCHARGE NOTICE Do not insert any foreign objects into the drive unit, since this may result in damage to the drive.
CHAPTER 1 INTRODUCTION 1.1 FEATURE SUMMARY ➀ ➁ ➂ ➃ ➄ ➅ USB 2.0 Interface. Automatic Loading with tray. Mechanical Shield for dust protection. BD-R/RE, DVD-RAM & DVD-R/RW media readable or writable Case and Bare type media supported. External Type design. This drive features both BD/DVD media reading and BD-R/BD-RE/DVD-RAM/DVD-R /DVD-RW media writing technology. But, CD writing is not supported This drive unit uses BD-R/RE discs which bear the following mark.
ENGLISH 1.3 SYSTEM REQUIREMENTS • CPU (Computer) Single CPU Multi CPU 32bit Xeon / Core2 by Intel 64bit AMD64 by AMD • Operating System Windows 2000 Professional Serve Advanced Server Datacenter Server Windows XP Home Edition Fedora Core x86 & x64 3 2. 6. 9-1. 667 4 20. 6. 11-1. 1369-FC4 5 2. 6. 15-1. 2054 6 2. 6. 18-1. 2798 7 2. 6. 21-1.
CHAPTER 2 PRECAUTIONS WHEN OPERATING 2.1 PRECAUTIONS WHEN TRANSPORTING To avoid damage * Keep the original packing materials for the drive unit. * Before you transport the drive unit, remove the disc from the drive unit and repack the drive unit in its original packing. 2.2 INSTALLATION LOCATION Do not place unit in the following environments. * High-temperature, high-humidity, extreme temperature changes. * Dusty * Excessive vibration/ sudden shock. * Inclined/ unstable place. * Direct sunlight. 2.
ENGLISH ➂ Do not write and paste anything on the recording/ reading side of the disc. Do not paste anything to all the surface of the BD-R/RE, DVD-RAM or DVD-R/RW disc. When labelling the BD-R/RE, DVD-RAM or DVD-R/RW disc for identification purposes, write only on the premarked label side using a soft, felt tip marker. Should not paste a large or thick label to the outer back surface (the label side) of the disc, or it generates drive vibration due to imbalance of the disc.
CHAPTER 3 PARTS AND FUNCTIONS ➀ 3.1 FRONT VIEW ➁ ➀ DISC TRAY ➂ ➃ ➄ Accepts a disc. ➁ EMERGENCY EJECT HOLE Insert the emergency ejection pin (attached) firmly into this hole to manually eject the tray. (Before proceeding with this emergency step, make sure that the power is switched OFF.) ➂ POWER LED Lights up when the drive power is ON. ➃ BUSY / WRITING INDICATOR Blinks when data is being accessed from the disc or the drive is writing onto the BD-R/RE or DVD-RAM/R/RW disc.
CHAPTER 4 CONNECTIONS AC (IN) Connector ENGLISH 4.1 CONNECTING VIEW USB Connector Drive Rear Side ➀ ➁ AC Power Cable USB(B type) Interface Cable To AC Power Outlet When connecting, connect in order of AC power cable ---> USB Interface Cable . When disconnecting, disconnect in converse order of the connecting. When you operate this product, the power outlet should be near the product and easily accessible.
CHAPTER 5 GUIDE TO OPERATION 5.1 INSTALLATIONS • Starting the drive. ➀ Turn on the power supply. ➁ Press the eject button. The tray is ejected from the drive. ➂ Place the disc according to each disc type as in the below figure. Case type (BD, DVD-RAM) : 1. Insert so the label-side of the shutter is facing up. 2. Push the case disc about 2 cm towards the drive. 3. Press gently on the shutter-label so the BD/DVD-RAM disc sits firmly on the tray. Non-case(Bare media) type : 1.
6.1 TROUBLESHOOTING (1) There are many kinds of problems caused by misuse. When a problem occurs, check the table below which describes possible problems occurring with your drive. (2) If the drive is not operating correctly and you cannot restore operation by following the detailed procedures in the table below, do not remove the cover of the units or adjust further. (3) In the case of (2) above, unplug the unit and consult with your dealer or the nearest service station.
CHAPTER 7 SPECIFICATION SUMMARY 7.1 GENERAL PERFORMANCE ➀ Power requirement 100 V – 240 V ~ AUTO 0.5 A – 0.3 A ➁ Dimensions (W x H x D) ➂ Weight 50 Hz / 60 Hz 168.5 mm x 56.8 mm x 290 mm 2435 g typ. 7.2 ENVIRONMENTAL CONDITIONS Operating • Temperature 5 °C ~ 35 °C • Humidity 10 %Rh ~ 80 %Rh (Max. wet bulb temp.