DVD-ROM DRIVE UNIT SR-8589-B / SR-8589-C INSTRUCTION MANUAL Please read through these instructions before operating this unit.
ENGLISH DVD-ROM DRIVE UNIT SR-8589-B / SR-8589-C INSTRUCTION MANUAL Please read through these instructions before operating this unit. Interface : ATAPI TABLE OF CONTENTS IMPORTANT SAFETY NOTICE ................................................................................ iv LASER SAFETY INFORMATION ............................................................................. A-1 INTRODUCTION ........................................................................................................ A-3 1.
IMPORTANT SAFETY NOTICE NOTICE (1) You may not reproduce or transcribe any part of this publication without permission. (2) We reserve the right to revise this document at any time without notice. (3) If you have any questions about this document, contact your sales representative. SAFETY NOTICE (1) To prevent fire or electric shock, do not expose this appliance to rain or moisture. (2) To avoid electric shock or damage to the eyes due to laser beam, do not attempt to disassemble the cabinet.
Class 1 LASER Product This equipment is certified to comply with DHHS Rule 21 CFR Chapter 1, Subchapter J in effect as of date of manufacture. Elsewhere, the drive is certified to conform to the requirements of the International Electrotechnical Commission (IEC) 60825-1 and CENELEC EN60825-1 for Class 1 laser products. Class 1 laser products are not considered to be hazardous. To ensure continued product safety, the following precautions should be heeded.
for DVD LASER Specification Type: Semiconductor laser InGaAlP / AlGaAs Wave Length: 650 ± 10 nm Divergence: θ = 24 ° ~ 32 ° (Typical 28 °) Output Power: 0.30 mW for CD LASER Specification Type:Semiconductor laser InGaAlP / AlGaAs Wave Length: 790 ± 15 nm Divergence: θ = 25 ° ~ 39 ° (Typical 32 °) Output Power: 0.
DVD-ROM is read-only memory using a CD-ROM disc system and an audio compact disc system as a media package which handles digital data. To enjoy audio CD, please insert the Headphone plug into the Headphone jack.(Model SR-8589-B only) This drive unit uses DVD-ROM discs which bear the following mark. or TM This drive unit uses CD-ROM discs which bear the following mark. COMPACT This drive unit uses CD-R discs which bear the following mark (read only).
CHAPTER 1 PRECAUTIONS WHEN OPERATING 1.1 PRECAUTIONS WHEN TRANSPORTING To avoid damage * Keep the original packing materials for the drive unit. * Before you transport the drive unit, remove the disc from the drive unit and repack the drive unit in its original packing. 1.2 INSTALLATION LOCATION Do not place unit in the following environments. * High-temperature, high-humidity, extreme temperature changes. * Dusty * Excessive vibration/ sudden shock. * Inclined place. * Direct sunlight. 1.
➂ Do not write on, or paste paper to the surface ENGLISH of the disc. Should not paste a large or thick label to the outer back surface (the label side) of the disc, or it generates drive vibration due to imbalance of the disc. ➃ Do not store the disc in a place where the temperature is high. ➄ Do not use benzine, thinners and cleaners, etc. T h inne r s B en zin e C le ane r s ➅ Do not make the center hole larger. ➆ Do not bend the disc. ➇ Do not drop the disc, or subject it to shock.
CHAPTER 2 PARTS AND FUNCTIONS 2.1 FRONT VIEW ➀ DISC TRAY ➀ ➁ ➂ ➃ ➅ Accepts a disc. ➄ ➁ HEAD PHONE JACK (Model SR-8589-B only) Headphone can be connected using a 3.5mm stereo mini plug. ➂ VOLUME (Model SR-8589-B only) Adjusts audio output level of Headphone. ➃ BUSY INDICATOR Lights when data is being accessed from the disc, or the drive is playing an audio CD. ➄ EJECT/LOAD BUTTON Ejects and loads the disc tray.
CHAPTER 3 CONNECTIONS DC (IN) Connector Interface Connector Jumper Pin DC Power Connector Audio Out Connector Digital Audio Out Connector Jumper Drive-Select (Master/Slave/CSEL) Cable select (CSEL) Slave Interface Cable Master CHAPTER 4 GUIDE TO OPERATION 4.1 INSTALLATIONS • Starting the drive. ➀ Turn on the power supply. ➁ Press the eject button. The tray is ejected from the drive. ➂ Place the disc in the tray with the disc’s label facing up.
CHAPTER 5 GENERAL DESCRIPTION 5.1 FEATURE SUMMARY ➀ Embedded ATAPI Interface. ➁ Automatic Loading with tray. ➂ Horizontal and Vertical Installation. (Vertical : Vertical installation type only, 12 cm Disc only) ➃ Audio Playback Capability. ➄ MS-DOS CD-ROM Extensions Available. ➅ 5 1/4” Half Height Design. 5.2 SYSTEM SET UP The ATAPI Devices are selected by the Address field in the Drive Select Register. When a single Device is attached to the interface, it shall be set as Device 0.
➄ Access time 105 ms [ typical ] 210 ms [ typical ] 90 ms [ typical ] 180 ms [ typical ] ➅ Buffer Size 256 KBytes MTBF 125,000 POH (duty 20%) ENGLISH Random access time (DVD CAV mode) *3 Fullstroke access time (DVD CAV mode) *4 Random access time (CD CAV mode) *5 Fullstroke access time (CD CAV mode) *6 NOTE: *1 CAV : Constant Angular Velocity *2 ZCLV: Zone Constant Linear Velocity *3 Random access time (DVD) :Average Data read over the complete area from starting data recorded area(LBA:0) to max
6.4 GENERAL PERFORMANCE ➀ Power rating ➁ Dimensions (W x H x D) ➂ Weight +5 V 1.0 A +12 V 2.0 A 146 x 41.3 x 190 mm(exclude Front Bezel) 835 g [ typical ] 6.5 ENVIRONMENTAL CONDITIONS Operating • Temperature 5 ~ 50 °C • Humidity 5 ~ 90 %RH (Max. wet bulb temp. is 29 °C, Non-condensation) Non-operating • Temperature • Humidity 6.
Weight and dimensions shown are approximate. Specifications are subject to change without notice.
