SUPERDISK USB DRIVE UNIT LKM-FK73-D INSTRUCTION MANUAL Please read through these instructions before operating the unit.
SUPERDISK USB DRIVE UNIT LKM-FK73-D INSTRUCTION MANUAL Please read through these instructions before operating the unit. Interface : USB TABLE OF CONTENTS IMPORTANT SAFETY NOTICE ................................................................................ iv INTRODUCTION ........................................................................................................ A-1 1. PRECAUTIONS WHEN OPERATING ................................................................... A-2 1.
IMPORTANT SAFETY NOTICE NOTICE (1) You may not reproduce or transcribe any part of this publication without permission. (2) We reserve the right to revise this document at any time without notice. (3) If you have any questions about contents of this document, contact your sales representative. SAFETY NOTICE (1) To prevent fire or electric shock, do not expose this drive unit to rain or moisture. (2) To avoid electric shock or damage to the eyes due to laser beam, do not attempt to disassemble the cabinet.
LASER SAFETY INFORMATION Class 1 LASER Product This equipment is certified to comply with DHHS Rule 21 CFR Chapter 1, Subchapter J in effect as of date of manufacture. Elsewhere, the drive is certified to conform to the requirements of the International Electrotechnical Commission (IEC) 825 and CENELEC EN60825 for Class 1 laser products. Class 1 laser products are not considered to be hazardous. To ensure continued product safety, the following precautions should be heeded.
LASER Specification Type: Semiconductor laser GaAlAs Wave Length: 795 ± 20 nm Divergence: θv = 30° ~ 36° Output Power: 3.
SuperDisk diskette can store high capacity data (240MB). This SuperDisk drive can read/ write the SuperDisk diskette and provides a full read/ write compatibility with the standard 3.5 " 2DD/ 2HD (720 KB/ 1.44 MB). 2HD floppy disk can be used as a high 32MB capacity media with this SuperDisk drive. This drive unit uses SuperDisk diskettes which bear the following marks. TM TM These marks are trademarks of Imation Corporation.
CHAPTER 1 PRECAUTIONS WHEN OPERATING 1.1 PRECAUTIONS WHEN TRANSPORTING To avoid damages * Keep the original packing materials for the drive unit. * Prior to sending the drive unit, remove the disk from drive unit and repack drive unit as it was originally packed. 1.2 INSTALLATION LOCATION Do not expose unit to the following environments. * High-temperature, high-humidity, extreme temperature changes. * Dusty * Excessive vibration/ sudden shock. * Inclined place. * Direct sunlight. 1.
English CHAPTER 2 PARTS AND FUNCTIONS 2.1 FRONT VIEW ➀ ➁ ➃ ➂ ➀ DISK SLOT Insert a disk. (See Section 4.1) ➁ BUSY INDICATOR Lights while a command from host is executed. (including read/ write operations) ➂ EJECT BUTTON (No function for Mac system) Ejects a disk. ➃ EMERGENCY EJECT HOLE Insert an instrument such as straightened paper clip pin into this hole to manually eject a disk. (See the lower part in Section 4.
2.2 REAR VIEW ➀ ➁ ➀ USB INTERFACE CABLE Connects the end of the cable to host computer’s USB interface port. ➁ EXPANSION CONNECTOR Not use normally.
English CHAPTER 3 CONNECTIONS 3.1 CONNECTING VIEW Rear Side of the drive unit USB Interface Cable To USB Port on Host PC Note : You can connect the SuperDisk drive while the host computer power is on (Hot-Plug). When hot-plugging, the host PC automatically recognizes the SuperDisk device if the SuperDisk device driver is already installed into the PC. The AC Adapter for this SuperDisk must be satisfied the below requirements. 1.
CHAPTER 4 GUIDE TO OPERATION 4.1 INSTALLATIONS • To start operation on drive. ➀ Turn on the power supply of Host PC. ➁ Plug the USB interface cable of the SuperDisc drive to Host PC USB port. (Refer the previous page) ➂ Insert a disk into the disk slot with the disk’s label facing up and the shutter side heading as shown in the below figure. CAUTION: • Do not insert any foreign objects into the disk slot. This could result in a malfunction.
English CHAPTER 5 GENERAL DESCRIPTION 5.1 SUMMARY OF FEATURES ➀ ➁ ➂ ➃ ➄ High Data Storage Capacity (with SuperDisk diskette) Full read/ write compatibility with the standard 2DD/ 2HD (720 KB/ 1.44 MB) Embedded USB Interface Cable (Power Supply capability) Slim Stand Alone Design 32MB Standard FD (2HD) Formatting function 5.2 SYSTEM SET UP The USB technology Devices are fully hot-pluggable to the USB-enabled computer.
CHAPTER 6 SPECIFICATION SUMMARY 6.1 PERFORMANCE ➀ Disk Diameter 3.5 inches ➁ Disk speed ➂ Storage Capacity Formatted ➃ ➄ ➅ ➆ 1500 r/min 120 MBytes (SuperDisk) 720 KB/1.44 MBytes(2DD/ 2HD) 32 MBytes (2HD 32MB Formatted) Recording Density 105.6 k FCI (SuperDisk) Track Density 2490 TPI (SuperDisk) Data Transfer Rate from Disk 600 KBytes/ s (SuperDisk) Seek Time (average) 95 ms [ typical ] (SuperDisk) MTBF 15,000 POH (@duty 25 %) 6.2 ERROR RATES • Hard read errors Less than 10 -12 6.
7.1 TROUBLESHOOTING (1) There are many kinds of problems caused by misuses. When a problem occurs, check the table below which describes possible problems occurring with your SuperDisk drive. (2) If the SuperDisk drive does not operate correctly and you cannot restore operation by the following detailed procedures in the table, do not remove the cover of the units or adjust further. (3) In the case of (2) above, unplug the unit and consult with your dealer or the nearest service station.
APPENDIX Installation of the SuperDisk Device Driver for Windows 98 This Device Driver software must be installed into your host computer before operating the SuperDisk drive. 1. Turn on the personal computer and start Windows 98. 2. Set the SuperDisk driver disc in your CD-ROM drive. 3. Open the Run… window from the Start menu. 4. Type "A:\SETUP.EXE" and press OK. (assumes that your drive is designed "A") 5. Follow the procedures displayed on the screen to install SuperDisk Device Driver.
English Formatting of SuperDisk / 2DD or 2HD disk for Windows 98 (You can also use the Formater attached with Windows 98) 1. Insert a disk that you wish to format into the SuperDisk drive. 2. Right-click on the " 3 1/2 Floppy " icon. 3. Left-click on the " Format utility For SuperDisk ". 4. " Format Utility for SuperDisk " window appears. Follow the procedures displayed on the screen to perform formatting of disk. Note : When formatting 2HD floppy disk, Not perform "Quick-Format".
Weight and dimensions shown are approximate. Specifications are subject to change without notice.
