DVD-R DRIVE UNIT SW-9501-S / SW-9501-T INSTRUCTION MANUAL Please read through these instructions before operating this unit.
DVD-R DRIVE UNIT SW-9501-S / SW-9501-T INSTRUCTION MANUAL Please read through these instructions before operating this unit. Interface : SCSI TABLE OF CONTENTS IMPORTANT SAFETY NOTICE 1. PRECAUTIONS WHEN OPERATING ................................................................... A-6 1.1 PRECAUTIONS WHEN TRANSPORTING ...................................................... A-6 1.2 INSTALLATION LOCATION ............................................................................ A-6 1.3 PRECAUTIONS FOR USE .
IMPORTANT SAFETY NOTICE NOTICE (1) You may not reproduce or transcribe any part of this publication without permission. (2) We reserve the right to revise this document at any time without notice. (3) If you have any questions about this document, contact your sales representative. SAFETY NOTICE (1) To prevent fire or electric shock, do not expose this appliance to rain or moisture. (2) To avoid electric shock or damage to the eyes due to laser beam, do not attempt to disassemble the cabinet.
LASER SAFETY INFORMATION Class 1 LASER Product This equipment is certified to comply with DHHS Rule 21 CFR Chapter 1, Subchapter J in effect as of date of manufacture. Elsewhere, the drive is certified to conform to the requirements of the International Electrotechnical Commission (IEC) 825 and CENELEC EN60825 for Class 1 laser products. Class 1 laser products are not considered to be hazardous. To ensure continued product safety, the following precautions should be heeded.
CAUTION – L ASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM ADVARSEL– º º VORSICHT– LASERSTRAHLUNG, WENN ABDECKUNG .. GEOFFNET, NICHT DEM STRAHL AUSSETZEN ADVARSEL – º º º LASERSTRALING VED ABNING. º º UNDGA UDSÆTTELSE FOR STRALING L ASERSTRALING NAR DEKSEL APNES. º º UNNGA EKSPONERING FOR STRALEN VARNING.. – º LASERSTRALNING NAR DENNA DEL .. .. .. º AR OPPNAD. STRAL EN AR FARLIG VARO ! AVATTAESSA OLET .. ALTTIINA L ASERSATEILYLLE. .. .. .. ALA KATSO SATEESEEN DANGER – L aser radiation when open.
LASER Specification Type: Semiconductor laser GaAlAs Wave Length: 655 ~ 664 nm Divergence: θ = 76.6 ° ± 4 ° Output Power: Read = 0.
IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Read all of these instructions. Save these instructions for later use. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Do not use this product near water. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.
INTRODUCTION This DVD-R drive features 650 nm Laser Wave Length & 4.7GB DVD-R Media Writing technology. DVD-R disc is compact disc memory that you can written high capacity digital data on the area one time and read with this DVD-R drive. This drive unit uses DVD-R discs which bear the following mark. or Writing or R4.7 R4.7 This drive unit uses DVD-ROM discs which bear the following mark.
CHAPTER 1 PRECAUTIONS WHEN OPERATING 1.1 PRECAUTIONS WHEN TRANSPORTING To avoid damage * Keep the original packing materials for the drive unit. * Before you transport the drive unit, remove the disc from the drive unit and repack the drive unit in its original packing. 1.2 INSTALLATION LOCATION Do not place unit in the following environments. * High-temperature, high-humidity, extreme temperature changes. * Dusty * Excessive vibration/ sudden shock. * Inclined place. * Direct sunlight. 1.
➂ Do not write on the recording / reading side, or paste paper to the surface of the disc. When labelling a disc for identification purposes, write only on the premarked label side using a soft, felt tip marker. ➃ Do not store the disc in a place where the temperature is high. ➄ Do not use benzine, thinners and cleaners, etc. T h inne r s B en zin e C le ane r s ➅ Do not make the center hole larger. ➆ Do not bend the disc. ➇ Do not drop the disc, or subject it to shock.
CHAPTER 2 PARTS AND FUNCTIONS 2.1 FRONT VIEW ➀ ➁ ➂ ➃ ➄ ➅ ➀ DISC TRAY Accepts a disc. ➁ BUSY INDICATOR Lights when data is being accessed from the disc. ➂ WRITING INDICATOR Lights when the drive is writing onto the writable disc. ➃ EMERGENCY EJECT HOLE Insert an instrument such as straightened paper clip into this hole to manually eject the tray. (See the lower part in Section 4.1) ➄ EJECT / LOAD BUTTON Ejects and loads the disc tray.
2.2 REAR VIEW ➀ ➀ ➁ ➂ ➃ ➀ SCSI INTERFACE CONNECTOR Connects to host computer’s SCSI interface connector. ➁ AC (IN) CONNECTOR Connects to AC power outlet using AC power cord. ➂ SCSI ID SWITCH Set ID-Number of SCSI interface. Push ( ID No. : Down ) Push ( ID No.
CHAPTER 3 CONNECTIONS 3.1 CONNECTING VIEW AC (IN) Connector SCSI connector on the rear side of the drive unit Interface Cable AC Power Cord To AC Power Outlet To SCSI Connector on Host Computer CAUTION : Input voltage changes automatically within a range of 100 V ~ to 240 V ~ .
CHAPTER 4 GUIDE TO OPERATION 4.1 INSTALLATIONS • Starting the drive. ➀ Turn on the power supply. ➁ Press the eject button. The tray is ejected from the drive. ➂ Place the disc in the tray with the disc's label facing up. ➃ Press the eject button or press the tray lightly as in the following figure. The tray is retracted automatically. ➄ Loading start. CAUTION: • Do not insert any foreign objects into the disc tray. This could result in a malfunction. • Do not manually force the tray to open.
CHAPTER 5 GENERAL DESCRIPTION 5.1 FEATURE SUMMARY ➀ Embedded SCSI-2 Interface. ➁ High Capacity Digital Data Write and Read Available. ➂ Coped with 650 nm Laser Wave Length & 4.7GB DVD-R Media Writing. ➃ TILT Servomechanism Equipped. 5.2 SYSTEM SET UP Hardware System [ Example of SCSI system set-up ] This unit consists as SCSI Device and basically must be installed in SCSI System.
CHAPTER 6 SPECIFICATION SUMMARY 6.1 PERFORMANCE ➀ Disc diameter 12cm, 8cm ➁ Disc speed (DVD Single Layer 1x mode) *1 (DVD Dual Layer 1x mode) 570 ~ 1390 r/min (CLV) *2 630 ~ 1530 r/min (CLV) ➂ Data capacity Reading Writing 3.95 / 4.7 GBytes (DVD-R) 4.7 GBytes (DVD-ROM Single Layer) 8.5 GBytes (DVD-ROM Dual Layer) 4.7 GBytes (DVD-R) Reading Writing 11.08 MBits/s (1x CLV) 11.08 MBits/s (1x CLV) Burst 10 MBytes/s Max.(Synchronous) 5 MBytes/s Max.
6.2 ERROR RATES Less than 10 -6 Less than 10 -12 • Soft read errors • Hard read errors 6.3 GENERAL PERFORMANCE ➀ Power requirement 100 – 240 V ~ AUTO 0.34 – 0.17 A 50 / 60 Hz 190 x 62.8 x 270 mm 2500 g [ typical ] ➁ Dimensions (W x H x D) ➂ Weight 6.4 ENVIRONMENTAL CONDITIONS Operating • Temperature • Humidity Non-operating • Temperature • Humidity 5 ~ 40 °C 5 ~ 90 %RH (Max. wet bulb temp. is 29 °C, Non-condensation) – 30 ~ 60 °C 5 ~ 95 %Rh (Non-condensation) 6.
CHAPTER 7 BEFORE REQUESTING SERVICE 7.1 TROUBLESHOOTING (1) There are many kinds of problems caused by misuse. When a problem occurs, check the table below which describes possible problems occurring with your DVD-R drive. (2) If the DVD-R drive is not operating correctly and you cannot restore operation by following the detailed procedures in the table below, do not remove the cover of the units or adjust further.
Weight and dimensions shown are approximate. Specifications are subject to change without notice.