SUPERDISK USB DRIVE UNIT LKM-RMB33 INSTRUCTION MANUAL Please read through these instructions before operating the unit.
SUPERDISK USB DRIVE UNIT LKM-RMB33 INSTRUCTION MANUAL Please read through these instructions before operating the unit. Interface : USB BUSY TABLE OF CONTENTS IMPORTANT SAFETY NOTICE 1. PRECAUTIONS WHEN OPERATING ................................................................... A-2 1.1 PRECAUTIONS WHEN TRANSPORTING ...................................................... A-2 1.2 INSTALLATION LOCATION ............................................................................ A-2 1.3 PRECAUTIONS FOR USE .
IMPORTANT SAFETY NOTICE NOTICE (1) You may not reproduce or transcribe any part of this publication without permission. (2) We reserve the right to revise this document at any time without notice. (3) If you have any questions about contents of this document, contact your sales representative. SAFETY NOTICE (1) To prevent fire or electric shock, do not expose this drive unit to rain or moisture. (2) To avoid electric shock or damage to the eyes due to laser beam, do not attempt to disassemble the cabinet.
LASER SAFETY INFORMATION Class 1 LASER Product This equipment is certified to comply with DHHS Rule 21 CFR Chapter 1, Subchapter J in effect as of date of manufacture. Elsewhere, the drive is certified to conform to the requirements of the International Electrotechnical Commission (IEC) 825 and CENELEC EN60825 for Class 1 laser products. Class 1 laser products are not considered to be hazardous. To ensure continued product safety, the following precautions should be heeded.
CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASER APPARAT APPAREIL A LASER DE CLASSE 1 EN60825 • • • • • • This label is attached to the bottom of the drive unit. Diese Aufschrift befinded sich auf der Bodenplatte des Gerätes. (For German) Märkningen återfinns på drivenhetens undersida. (For Sweden) Denne merkelappen er festet til undersiden av spilleren. (For Norway) Denne etiket er sat fast i bunden af drev-enheden. (For Denmark) Tämä etiketti on liimattu laitteen pohjaan.
INTRODUCTION SuperDisk diskette can store high capacity data (up to 83 disks of the standard FD). This SuperDisk drive can read/ write the SuperDisk diskette and provides a full read/ write compatibility with the standard 3.5 " 2DD/ 2HD (720 KB/ 1.44 MB). This drive unit uses SuperDisk diskettes which bear the following mark. TM This mark is a trademark of Imation Corporation.
CHAPTER 1 PRECAUTIONS WHEN OPERATING 1.1 PRECAUTIONS WHEN TRANSPORTING To avoid damages * Keep the original packing materials for the drive unit. * Prior to sending the drive unit, remove the disk from drive unit and repack drive unit as it was originally packed. 1.2 INSTALLATION LOCATION Do not expose unit to the following environments. * High-temperature, high-humidity, extreme temperature changes. * Dusty * Excessive vibration/ sudden shock. * Inclined place. * Direct sunlight. 1.
CHAPTER 2 PARTS AND FUNCTIONS 2.1 FRONT VIEW ➀ ➃ BUSY ➁ ➂ ➀ DISK SLOT Insert a disk. ➁ BUSY INDICATOR Lights while a command from host is executed. (including read/ write operations) ➂ EJECT BUTTON Ejects a disk. ➃ EMERGENCY EJECT HOLE Insert an instrument such as straightened paper clip pin into this hole to manually eject a disk. (See 4.
2.2 REAR VIEW ➀ DC IN 5V + – ➁ ➀ POWER INDICATOR Lights up while the drive power is on. ➁ DC (IN) CONNECTOR Connects to 5V DC power source. ➂ USB CONNECTOR Connects to host computer’s USB interface port.
CHAPTER 3 CONNECTIONS 3.1 CONNECTING VIEW Rear Side of the drive unit INTERFACE 5V DC Power Cable USB Interface Cable To USB Port on Host PC From 5V DC Power Source Note : When you connect the SuperDisk drive while the host computer power is on (hot-plug), first, the SuperDisk drive must be plugged to 5 V DC power source, and next, plugged to USB port on the host computer in the order. When you disconnect, unplug in the reverse order. If not, the host computer may hang-up.
CHAPTER 4 GUIDE TO OPERATION 4.1 INSTALLATIONS • To start operation on drive. ➀ Turn on the power supply of Host PC. ➁ Plug the 5V DC cable and USB interface cable from Host PC to the SuperDisc drive. (Refer the previous page) ➂ Insert a disk into the disk slot with the disk’s label facing up and the shutter side heading as shown in the figure below. BUSY CAUTION: • Do not insert any foreign objects into the disk slot. This could result in a malfunction.
CHAPTER 5 GENERAL DESCRIPTION 5.1 SUMMARY OF FEATURES ➀ ➁ ➂ ➃ ➄ High Data Storage Capacity (with SuperDisk diskette) Full read/ write compatibility with the standard 2DD/ 2HD (720 KB/ 1.44 MB) Embedded USB Interface Slim Stand Alone Design Horizontal Installation Type 5.2 SYSTEM SET UP The USB technology Devices are fully hot-pluggable to the USB-enabled computer. The SuperDisk drive with USB interface is able to be attached to host computer and used without turning off or rebooting the computer. 5.
CHAPTER 6 SPECIFICATION SUMMARY 6.1 PERFORMANCE ➀ Disk Diameter 3.5 inches ➁ Disk speed 720 r/min ➂ Storage Capacity (Formatted) 120 MBytes (SuperDisk) 720 KB/1.44 MBytes (2DD/ 2HD) ➃ Recording Density 33.8 k FCI (SuperDisk) ➄ Track Density 2490 TPI (SuperDisk) ➅ Typical Sustained Transfer Rate from Disk 266 ~ 479 KBytes/ s (SuperDisk) ➆ Seek Time (average) 70 ms typical MTBF 15,000 POH (@duty 25 %) 6.2 ERROR RATES • Hard read errors Less than 10 -12 6.
CHAPTER 7 BEFORE REQUESTING SERVICE 7.1 TROUBLESHOOTING (1) There are many kinds of problems caused by misuses. When a problem occurs, check the table below which describes possible problems occurring with your SuperDisk drive. (2) If the SuperDisk drive does not operate correctly and you cannot restore operation by the following detailed procedures in the table, do not remove the cover of the units or adjust further.
APPENDIX Installation of the SuperDisk Device Driver for Windows 98 This Device Driver software must be installed into your host computer before operating the SuperDisk drive. 1. Turn on the personal computer and start Windows 98. 2. Set the SuperDisk driver disc in your CD-ROM drive. 3. Open the Run… window from the Start menu. 4. Type "A:\SETUP.EXE" and press OK. (assumes that your drive is designed "A") 5. Follow the procedures displayed on the screen to install SuperDisk Device Driver.
Weight and dimensions shown are approximate. Specifications are subject to change without notice.