Personal Computer OPERATING INSTRUCTIONS Model No. CF-29 Series Getting Started Read Me First.................................................. 3 Names and Functions of Parts ........................ 9 First-time Operation ......................................
Customer's Record Model No.* Dealer's Name Serial No. or Code No. Dealer's Address Date of Purchase Getting Started * For the Model No., insert the 12 digit number (for example, CF-29ETKGZKM) located on the bottom of the computer. Introduction Thank you for purchasing the Panasonic computer. Read the operating instructions thoroughly for proper operation of your new computer.
Read Me First For U.S.A. Federal Communications Commission Radio Frequency Interference Statement FCC Regulation Notice for modem This equipment contains a FCC approved modem. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Read Me First 10.According to the FCC’s electrical safety advisory, we recommend that you may install an AC surge arrestor in the AC outlet to which this equipment is connected. Telephone companies report that electrical surges, typically lightning transients, are very destructive to customer terminal equipment connected to AC power sources and that this is a major nationwide problem. Notice for the products using LCD This product uses one or more fluorescent lamps containing a small amount of mercury.
For Europe Network connection. The terminal equipment is intended for connection to the following public network; In all the countries of European Economical Area; - Public Switched Telephony Networks Technical Features. The terminal equipment includes the following features; - DTMF dialing - Maximum bitrate receiving mode: 56 kbits/s - Maximum bitrate sending mode: 33.
Read Me First Getting Started Important Safety Instructions / Importantes Mesures De Sécurité When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: Certaines mesures de sécurité doivent être prises pendant l'utilisation de matérial téléphonique afin de réduire les risques d'incendie, de choc électrique et de blessures. En voici quelquesunes: 1.
The CF-29 was developed based on thorough research into the real-world portable computing environments. Exhaustive pursuit of usability and reliability under harsh conditions led to innovations such has the magnesium alloy exterior, vibration damped hard disk drive and floppy disk drive, flexible internal connections. The CF-29’s outstanding engineering has been tested using the stiff MIL-STD- 810F (for vibration and shock) and IP (for dust and water) based procedures.
Read Me First Getting Started Precautions (Battery Pack) 8 If the battery pack will not be used for a long period of time (a month or more), charge or discharge (use) the battery pack until the remaining battery level becomes 30% to 40% and store it in a cool, dry place. This computer prevents overcharging of the battery by recharging only when the remaining power is less than approx. 95% of capacity. The battery pack is not charged when the computer is first purchased.
Names and Functions of Parts The illustrations shown may differ from the actual physical appearances. LCD (Only for models with touchscreen: “Touchscreen”) CAUTION Do not allow metallic objects or magnetic media to come in close proximity to this area. Modem ( Keyboard DC-IN Jack Touch Pad ( page 19) Power Switch “Modem”) DC IN 15.6V USB Port ( “USB Devices”) Depending on the shape of the plug, some USB devices cannot be connected to the USB port.
Names and Functions of Parts Getting Started Headphone Jack External Display Port “External Display”) Use this connector to connect headphones or amplifierequipped speakers. Audio output from the internal speaker is disabled when headphones or external speakers are connected. ( External Keyboard/Mouse Port Expansion Bus Connector ( “Port Replicator”) Security Lock Parallel Port Serial Port LOCK A cable can be connected to prevent theft of your computer.
First-time Operation Read the steps below to help you learn what parts are included, and to gain an understanding of some basic computer-related operations. 1 Confirm the inclusion of all parts. Make sure the parts shown in the figure have been supplied. If any of these items are missing or are not working properly, contact Panasonic Technical Support. AC Adaptor ............................... 1 AC Cord ..................................... 1 Battery Pack..............................
First-time Operation 3 Slide the battery pack inward until it is firmly in place. CAUTION 4 3 Do not touch the terminals on the battery pack and the computer. The battery pack may no longer function properly if the contacts are dirty or damaged. Also, the computer may not operate properly. Be sure to insert the battery pack as illustrated. 4 Close the cover until it clicks into place. 5 Lock the cover by sliding the latch to the left.
7 Setup Windows. Moving the cursor ( ) or clicking buttons can be performed with the touch pad. NOTE The touchscreen does not work properly during the Windows setup. CAUTION 1 At [Welcome to the Windows XP Setup Wizard], select [Next]. 2 After reading the agreement, select [I accept this agreement] or [I don’t accept this agreement], then select [Next]. NOTE If [I don’t accept this agreement] is selected, the Windows setup will be aborted. 3 Select settings for your region, then select [Next].
First-time Operation 9 Create a new account. Select [start] - [Control Panel] - [User Accounts] - [Create a new account]. Enter a name for the new account, then select [Next]. Select [Computer administrator], then select [Create Account]. Select the new account you have created and select [Create a password]. Follow the instructions on the screen to create a password. 5 Select [start] - [Turn Off Computer] - [Restart] to restart the computer.
Information for Windows XP Depending on the Windows settings, installed applications, and drivers, menus and other displays may differ, or some functions (such as use of the password reset disk) may be inoperable. Check with your system administrator for details. Resetting the password Windows XP has a function to reset a forgotten password. To use this function, you need to create a password reset disk beforehand following the steps below. 1 Select [start] - [Control Panel] - [User Accounts].
Starting Up/Shutting Down Starting Up Latch 3 1 Open the display. 1 Pull the carrying handle forward. 2 Press the latch as illustrated. 3 Lift up the latch and open the display. 2 1 Power Indicator 2 Turn your computer on. Slide the power switch and hold it for approximately one second until the power indicator turns on before releasing it.
3 Log on to Windows. After confirming that the hard disk drive indicator ( ) has turned off, select the user and input the password, then select . Until the correct password is entered, the computer will not operate. 4 Select your application. You are able to start working on your computer.
Starting Up/Shutting Down Shutting Down (power off your computer) 1 Save important data and close each application. 2 Select [start] - [Turn Off Computer]. 3 Select [Turn Off]. Your computer will power off automatically. Restarting your computer (without shutting down) Select [Restart]. To shut down using the keyboard; Press , U , and select [Turn Off] with U . CAUTION Do not do the following during the shutdown/restart procedure. • Connecting or disconnecting the AC adaptor.
Touch Pad (Basic Operation) Work Surface Use the touch pad to move the cursor on the screen and perform computer operations. For instructions on how to operate, refer to “Touch Pad”. Function Touch Pad Operation Moving the Cursor Move the tip of your finger lightly over the surface.
Reference Manual The Reference Manual and the Important Tips can be accessed on your computer. When a printer is connected, these manuals can also be printed. The Reference Manual explains functions for you to make greater use of the computer, such as how to add peripheral devices, how the Setup Utility works, and other useful information. (Refer to the cover of this manual for a list of the main contents included.
Useful Information Usage Environment Environment In use: Temperature: 5 °C to 35 °C {41 °F to 95 °F} Humidity : 30% to 80% RH (No condensation) Not in use: Temperature: -20 °C to 60 °C {-4 °F to 140 °F} Humidity : 30% to 90% RH (No condensation) NOTE Only use the computer within the allowable temperature range. When the computer is left powered on in a low temperature environment, set [Turn off hard disks] to [Never] in the following menu to avoid damage to the hard disk drive.
Useful Information Maintenance Touch Pad page 19 Display Use the Soft Cloth included with the computer. (For more information, refer to “Suggestions About Cleaning the LCD Surface” that come with the Soft Cloth.) If the Protective Film becomes dirty or damaged, it may be time to replace your Protective Film. The Protective Film is a disposable item. To find out the model number of your Protective Film, contact Panasonic Technical Support.
Saving Data on Floppy Disks Write-protect Tab Write Enable Write Disable Do not power down your computer or press the disk eject button while the Multimedia pocket device indicator ( ) is on. Doing so may damage the data on the floppy disk and render the floppy disk useless. Use care when handling floppy disks. To protect the data on your floppy disks or to prevent a floppy disk from becoming stuck in your computer, avoid the following: • Sliding the shutter on the floppy disk manually.
Useful Information Windows Update You can use the latest patches and service packs for Windows with the following menus. Do not apply “Driver Updates” even if a message to update a driver appears. If a driver update is required, contact to Panasonic Technical Support. [start] - [All programs] - [Windows Update] When Changing Hard Disk Partitions When using the hard disk backup function ( page 35), do not divide up the hard disk before creating a backup region.
List of Error Codes When turning on the computer, if one of the following error codes or messages is displayed, follow the instructions shown below. If the problem persists, or if the error code or message displayed is not shown here, contact Panasonic Technical Support.
Dealing with Problems (Summary) When a problem occurs, refer to this page. The “Reference Manual” also contains detailed information. If a problem appears to be related to a software application, read the software related manual. If you still cannot troubleshoot the problem, contact Panasonic Technical Support. You can use the PC Information Viewer to check the computer ’s usage status.
Starting Up (continued) When the previous item is not the cause Press F9 in the Setup Utility ( “Setup Utility”). This will restore the Setup Utility’s settings to their default values (except the password settings). Try removing all peripheral devices. Check a disk error using the following procedure. 1 Select [Local Disk(C:)] with the right button in [start] - [My Computer], and select [Properties]. 2 Select [Tools] - [Check Now]. 3 Select [Start] after selecting required items in [Check disk options].
Dealing with Problems (Summary) Display (continued) During simultaneous display, one of the screens becomes disordered When an a moving picture such as an MPEG file is being played with Media Player, the display destination cannot be switched using Fn + F3 Try changing the display by pressing Fn + F3 . If you continue to experience problems, try changing the display destination in the following menu.
Touch Pad / Touchscreen (only for models with touchscreen) The cursor cannot be controlled properly The cursor does not move in scrolling area of the touch pad Unable to input using the touch pad Unable to point correctly with the stylus included with the computer Unable to input by touching the display If you are using an external mouse, ensure that the external mouse has been connected correctly. Restart the computer by using the keyboard (Press , U , and select [Restart] with R ).
Dealing with Problems (Summary) Others (continued) Troubleshooting When trying to play back video files using Windows® Media Player, the message [Codec required] appears, and the file cannot be played back The shortcut icon for the Windows® Media Player is not displayed on the desktop Two shortcut icons for the Windows® Media Player are displayed on the desktop 30 Some video files use a Codec that is not installed as a standard.
Reinstalling Software When reinstallation procedure is performed, the contents of the hard disk will be erased. Be sure to back up any critical data on your hard disk to another media or to an external hard disk before running the reinstallation procedure. The reinstallation procedure will return the computer to its original condition. Even if a hard disk backup area has been created, this backup area will be erased, and all the backed up data will be lost.
Reinstalling Software 9 Make a selection from the menu. NOTE When [2] is selected, the hard disk backup function cannot be enabled because the hard disk has been divided into partitions. When selecting [2], enter the basic partition size for the operating system installation and press Enter . (The data partition size is the remainder after subtracting the basic partition size.) To select [3], the initial partition size must be 6 GB or more of the hard disk size.
LIMITED USE LICENSE AGREEMENT THE SOFTWARE PROGRAM(S) (“PROGRAMS”) FURNISHED WITH THIS PANASONIC® PRODUCT (“PRODUCT”) ARE LICENSED ONLY TO THE END-USER (“YOU”), AND MAY BE USED BY YOU ONLY IN ACCORDANCE WITH THE LICENSE TERMS DESCRIBED BELOW. YOUR USE OF THE PROGRAMS SHALL BE CONCLUSIVELY DEEMED TO CONSTITUTE YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE. Matsushita Electric Industrial Co., Ltd. (“MEI”) has developed or otherwise obtained the Programs and hereby licenses their use to you.
Contrat de licence d’usage limité Le(s) logiciel(s) (les “Logiciels”) fournis avec ce produit Panasonic® (le “Produit”) sont exclusivement concédés en licence à l’utilisateur ultime (“vous”), et ils ne peuvent être utilisés que conformément aux clauses contractuelles cidessous. En utilisant les logiciels, vous vous engagez de manière définitive à respecter les termes, clauses et conditions des présentes. Matsushita Electric Industrial Co., Ltd.
Hard Disk Backup Function The hard disk backup function creates a backup area (storage area) on the hard disk. This area is to back up (store) hard disk contents or restore backed up contents to their original locations. By backing up the data on your hard disk to a backup area, you can protect your data from loss or damage resulting from operational errors or other factors.
Hard Disk Backup Function NOTE Regarding backup area • Requires availability of at least half of the entire hard disk. Without sufficient space available, the backup area cannot be created. • When the backup area is created, the usable hard disk capacity will be reduced to less than half. • The backup area cannot be accessed from Windows. For this reason, backed up data cannot be copied to CD-R or other removable disk media.
Select [2], enter the partition size (GB), and press Enter . • You can cancel this operation by pressing 0 . • The data partition size will be the maximum settable size less the number entered above. The maximum settable size will differ depending on models. [At the time of purchase] [After the backup area is created] The usable hard disk area Can be accessed from Windows (Two partitions).
Hard Disk Backup Function 3 Select the operation to be executed from the menu. 1 Press 1 to execute [1. [Backup]]. (When dividing the hard disk into two partitions, select the backup method at next screen.) 2 At the confirmation message, press Y . The backup process will begin. 1 Press 2 to execute [2. [Restore]]. (When data is backed up in two partitions, select the restore method at next screen.
Hard Disk Data Erase Utility This computer is equipped with a utility for erasing hard disk data. When disposing of or transferring ownership of this device, erase all data on the hard disk in order to prevent the theft of hard disk data following the steps below. The hard disk data erase utility erases data using an “overwriting” method, but there is a possibility that due to malfunctions or other operational errors, data may not be completely erased.
Specifications Main Specifications Model No.
Main Specifications Model No. Battery Pack Operating Time*9 Charging Time*9 Power On Power Off Clock Battery AC Adaptor*12 Input Output Power Consumption*13 Environment In use Temperature Humidity Not in use Temperature Humidity Physical Dimensions (W x H x D) Weight (including the carrying handle) *9 *10 *11 *12 *13 *14 CF-29ETKGZKM CF-29ETPGZKM CF-29E3KGZKM Li-ion 11.1 V, 6.6 Ah Main battery: Approx. 5 hours - 8.5 hours*10 (Approx. 7.5 hours*11) Main battery + Second battery: Approx.
LIMITED WARRANTY For U.S.A. PANASONIC PERSONAL COMPUTER AND PERIPHERALS LIMITED WARRANTY Panasonic Computer Solutions Company (referred to as “Panasonic”) will repair this product (other than software, which is covered by a separate warranty) with new or rebuilt parts, free of charge in the U.S.A. for three (3) years from the date of original purchase in the event of a defect in materials or workmanship.
For Canada PANASONIC COMPUTER AND PERIPHERALS LIMITED WARRANTY Coverage – Panasonic Canada Inc. (“PCI”) warrants to you, the first end user customer, this computer product (excluding software media), when purchased from PCI or from a PCI authorized reseller, to be free from defects in materials and workmanship under normal use, subject to the terms set forth below, during the period of warranty coverage specified.
As an ENERGY STAR® Partner, Matsushita Electric Industrial Co., Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Outline of the International ENERGY STAR® Office Equipment Program The international ENERGY STAR® Office Equipment Program is an international program that promotes energy saving through the use of computers and other office equipment.
ADDENDUM External antenna cannot exceed recommended maximum antenna gain as described below. Maximum External Antenna Gain Module Band Gain (dBi) WLAN 2.4GHz GPRS Cellular 3.75 PCS 4.15 CDMA 12.5 Cellular 13.35 PCS 11.