OPERATING INSTRUCTIONS Personal Computer Model No. CF-18 Series Getting Started Read Me First ................................................. 3 Names and Functions of Parts ........................ 9 First-time Operation ...................................... 13 Tablet PC Reference Manual • Read Me First • Key Combinations • LED Indicators Getting Started Contents Starting Up/Shutting Down............................ 18 Touch Pad (Basic Operation) .............................
Customer's Record Model No.* Dealer's Name Serial No. or Code No. Dealer's Address Getting Started Date of Purchase * For the Model No., insert the 12 digit number (for example, CF-18FDAZXVM) located on the bottom of the computer. Introduction Thank you for purchasing the Panasonic computer. Read the operating instructions thoroughly for proper operation of your new computer.
Read Me First For U.S.A. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Responsible Party: Panasonic Corporation of North America One Panasonic Way Secaucus, NJ 07094 Tel No:1-800-LAPTOP5 (1-800-527-8675) FCC Regulation Notice for modem This equipment contains a FCC approved modem.
Getting Started Read Me First 9.
This product (local network devices) for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LELAN devices. CSA C22 2 NO.213-conforming model. (The model which has description of “CSA C22 2 NO.
Read Me First Getting Started Important Safety Instructions / Importantes Mesures De Sécurité When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1.Do not use this product near water, for example, near a bath tub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. 2.Avoid using a telephone (other than a cordless type) during an electrical storm.
The CF-18 was developed based on thorough research into the real-world portable computing environments. Exhaustive pursuit of usability and reliability under harsh conditions led to innovations such has the magnesium alloy exterior, vibration damped hard disk drive and floppy disk drive, flexible internal connections. The CF-18’s outstanding engineering has been tested using the strict MIL-STD- 810F (for vibration and shock) and IP (for dust and water) based procedures.
Read Me First Getting Started Precautions ( Battery Pack ) 8 If the battery pack will not be used for a long period of time (a month or more), charge or discharge (use) the battery pack until the remaining battery level becomes 30% to 40% and store it in a cool, dry place. This computer prevents overcharging of the battery by recharging only when the remaining power is less than approx. 95% of capacity. The battery pack is not charged when the computer is first purchased.
Names and Functions of Parts The illustrations shown may differ from the actual physical appearances. Pen ( page 22) Wireless LAN Antenna Keyboard ( “Wireless LAN”) LED Indicators “LED Indicators”) Caps Lock Numeric Key (NumLk) Scroll Lock (ScrLk) Hard disk drive status Battery pack status Power status LCD ( Getting Started ( page 22) Function Keys For information on the key combinations available.
Names and Functions of Parts External Display Port Getting Started Security Lock LOCK A cable can be connected to prevent theft of your computer. For more information, read the manual provided with the cable. ( “External Display”) Modem ( Microphone Jack Use only a monaural condenser microphone (miniature jack). Using an input source other than a monaural condenser microphone may not allow audio to be input or may damage the equipment.
( Expansion Bus Connector “Port Replicator”) CAUTION RAM Module Slot ( “RAM Module”) Speaker Getting Started Do not allow metallic objects or magnetic media to come near these areas. To adjust the volume: Fn + F5 / Fn + F6 Speaker on/off : Fn + F4 CAUTION Do not allow metallic objects or magnetic media to come near the speaker on the bottom surface of the computer. • Because the speaker contains a magnet, metal objects may become attached to the bottom surface of the computer.
Names and Functions of Parts Using the Tether Getting Started The tether can be attached to the bottom right or bottom left corner of the display. It prevents the pen (included) from falling accidentally. Attaching the Tether 1 3 Tether 2 4 CAUTION When closing the display, be careful not to catch the tether between the display and main part of the computer. (See the figure below.
First-time Operation Read the steps below to help you learn what parts are included, and to gain an understanding of some basic computer-related operations. 1 Confirm the inclusion of all parts. Make sure the parts shown in the figure have been supplied. If any of these items are missing or are not working properly, contact Panasonic Technical Support. AC adaptor ..........1 AC Cord ...............1 Battery Pack ........1 Modem Telephone Cable ...................... 1 Soft Cloth ...............
First-time Operation DC-IN Jack 4 Connect your computer to a power outlet. DC IN 16 V CAUTION Getting Started Be sure the AC adaptor is connected until completing the first-time use operation. When using the computer for the first time, do not connect any peripheral device except the battery pack and AC adaptor to the computer. Handling the AC adaptor Do not twist or pull the AC power cord forcefully. Doing so may damage the connections. Use only the specified AC adaptor with your computer.
5 Enter your computer name and administrator password and then select [Next]. CAUTION Remember this password! If the password is forgotten, Windows cannot be operated. 6 Enter the correct date, time and time zone, then select [Next]. The computer will restart. It may take some time before the computer restarts and the screen of step 7 is displayed. Wait, and do not press any keys, or touch the touch pad, etc. 7 Enter your administrator password and select .
First-time Operation Getting Started NOTE When creating a new user account: • If you make mail settings, create password reset disks ( page 17), or conduct other related operations before creating the user account, you will be unable to use any previous mail history or settings. • When you create the first new account, you can only select [Computer administrator]. Once a “Computer Administrator” account has been created, you can create additional limited user accounts.
Information for Windows XP Depending on the Windows settings, installed applications, and drivers, menus and other displays may differ, or some functions (such as use of the password reset disk) may be inoperable. Check with your system administrator for details. Resetting the password Windows XP has a function to reset a forgotten password. To use this function, you need to create a password reset disk beforehand following the steps below.
Starting Up/Shutting Down Starting Up Latch B 2 1 Open the display. 1 Pull up latch A and release latch B. 2 Lift open the display. 1 Latch A 2 Turn your computer on. Slide the power switch and hold it for approximately one second until the power indicator turns on before releasing it. Power Switch CAUTION Operation Power Indicator While booting, avoid the following until the hard disk drive indicator ( ) has turned off. • Connecting or disconnecting the AC adaptor.
3 Log on to Windows. After confirming that the hard disk drive indicator ( ) has turned off, select the user and input the password, then select . Until the correct password entered, the computer will not operate. 4 Select your application. You are able to start working on your computer.
Starting Up/Shutting Down Shutting Down (power off your computer) 1 Save important data and close each application. 2 Select [start] - [Turn Off Computer]. 3 Select [Turn Off]. Your computer will power off automatically. Restarting your computer (without shutting down) Select [Restart]. To shut down using the keyboard; Press , U , and select [Turn Off] with U . CAUTION Do not do the following during the shutdown/restart procedure. • Connecting or disconnecting the AC adaptor.
Touch Pad (Basic Operation) Work Surface Use the touch pad to move the cursor on the display and perform normal computer operations. For instructions on how to operate, refer to “Touch Pad”. Function Touch Pad Operation Moving the Cursor Move the tip of your finger lightly over the surface.
Digitizer (Basic Operation) Your computer is equipped with a digitizer function allowing you to perform the same operations as the touch pad or mouse by touching the surface of the display with the pen (included). (The following explanation gives one example (for the default settings).) The operation settings can be changed. For detailed information, refer to “Digitizer”.
Operating in Tablet Mode In addition to being used as a regular notebook computer (Laptop mode), this computer can also be operated in Tablet mode. Simply turn the display around 180°, and close the computer with the display facing up. In Tablet mode, the computer can be operated using the digitizer ( page 21), the Input Panel and the tablet buttons ( “Tablet Buttons”), instead of the internal keyboard and the touch pad. Set the computer in Tablet mode using the following procedure.
Operating in Tablet Mode Changing the Display Settings Pen To rotate the display Press the rotation button until the display is set at the angle that is most comfortable for you. For detailed information, refer to “Display Rotation” Tablet Buttons LCD brightness control Input Panel Enter Rotation Security NOTE You can set the computer so that the display automatically rotates to your preferred angle when changing from Laptop Mode to Tablet Mode or vice versa.
Reference Manual The Reference Manual and the Important Battery Tips can be accessed on your computer. When a printer is connected, these manuals can also be printed. Reference Manual The Reference Manual explains functions for you to make greater use of the computer, such as how to add peripheral devices, how the Setup Utility works, and other useful information. (Refer to the cover of this manual for a list of the main contents included.
Useful Information Usage Environment Environment Operation: Temperature: 5 °C to 35 °C {41 °F to 95 °F} Humidity : 30% to 80% RH (No condensation) Storage: Temperature: -20 °C to 60 °C {-4 °F to 140 °F} Humidity : 30% to 90% RH (No condensation) Even within the temperature and humidity ranges noted above, using the computer for long periods of time in an environment with exceptionally low or high temperatures or high humidity may result in deterioration of the product, which can lead to a reduction in produ
Maintenance Touch Pad page 21 Display Use the Soft Cloth included with the computer. (For more information, refer to “Suggestions About Cleaning the LCD Surface” that comes with the Soft Cloth.) If the Protective Film becomes damaged, it may be time to replace your Protective Film. The Protective Film is a disposable item. To find out the model number of your Protective Film, contact Panasonic Technical Support.
Useful Information If the message “Your computer might be at risk” is displayed Read the message, select (red icon) on the taskbar, and make the appropriate settings. This message, which the Windows Security Center ( page 27) displays to confirm the securityrelated settings regularly, will be displayed until the settings are made more properly. NOTE This message does not indicate an error. You can use the computer while the message is displayed.
When Using Peripheral Devices Pay strict attention to the following points to avoid damage to the computer, peripheral devices, cables, etc. Also, in addition to following this manual and the Reference Manual, carefully read the instruction manuals for the peripheral devices being used. Use only peripheral devices that conform to the computer’s specifications. Connect the devices properly, paying close attention to the condition and position of the connectors.
List of Error Codes When turning on the computer, if one of the following error codes or messages is displayed, follow the instructions shown below. If the problem persists, or if the error code or message displayed is not shown here, contact Panasonic Technical Support. Action If an external keyboard or mouse is connected, disconnect these devices. An error has occurred in the memory that stores the Setup Utility settings.
Dealing with Problems (Summary) When a problem occurs, refer to this page. The “Reference Manual” also contains detailed information. If a problem appears to be related to a software application, read the software related manual. If you still cannot troubleshoot the problem, contact Panasonic Technical Support. You can use the PC Information Viewer to check the computer’s usage status.
Dealing with Problems (Summary) Starting Up (continued) When the previous item is not the cause Press F9 in the Setup Utility ( “Setup Utility”). This will restore the Setup Utility’s settings to their default values (except the password settings). Try removing all peripheral devices. Check a disk error using the following procedure. 1 Select [start] - [My Computer], and select [Local Disk(C:)] with the right button. 2 Select [Properties]. 3 Select [Tools] - [Check Now].
Display (continued) During simultaneous display, one of the screens becomes disordered When an a moving picture such as an MPEG file is being played with Media Player, the display destination cannot be switched using Fn + F3 Try changing the display by pressing Fn + F3 . If you continue to experience problems, try changing the display destination in the following menu.
Dealing with Problems (Summary) Touch Pad / Digitizer The cursor cannot be controlled properly The cursor does not move in scrolling area of the touch pad Unable to input using the touch pad Unable to use the digitizer function If you are using an external mouse, ensure that the external mouse has been connected correctly. Restart the computer by using the keyboard (Press , U , and select [Restart] with R ). If the computer does not respond to keyboard commands, read “No response” ( page 35).
Others When trying to play back video files using Windows® Media Player, the message [Codec required] appears, and the file cannot be played back Cannot start a networkused program, or cannot share files or printers Is it necessary to enable the Windows Firewall? When “Automatic Updates” is enabled, will all updates be downloaded (or installed)? Security Center warning function does not operate Press Ctrl + Shift + Esc to open Task Manager and close the software application which is not responding.
Dealing with Problems (Summary) Others (continued) Problem with Web page display (no display; display is completely white; advertisements, logon, and other popups are not displayed) Images in HTML e-mail messages are not displayed in Outlook Express Cannot read attachment file in Outlook Express (cannot save file) Troubleshooting The message “Your computer might be at risk” is displayed 36 In Windows XP, security functions have been strengthened with regard to Web contents.
Others (continued) Some applications do not work properly This message is displayed because the “Automatic Updates” setting in the “Security Center” is disabled or is not set. (Settings have not been made at the time of purchase.) “Automatic Updates” is a function that regularly checks whether high-priority update programs (security updates, etc.) have been provided to Windows Update, and automatically installs these programs to maintain Windows in its latest condition.
Reinstalling Software When reinstallation procedure is performed, the contents of the hard disk will be erased. Be sure to back up any critical data on your hard disk to another media or to an external hard disk before running the reinstallation procedure. The reinstallation procedure will return the computer to its original condition. Even if a hard disk backup area has been created, this backup area will be erased, and all the backed up data will be lost.
10 At the confirmation message , press Y . The operation of reinstallation for the hard disk starts automatically. (The operations take about 20 minutes.) CAUTION Do not interrupt the reinstallation procedure before completion, for example by turning off the computer or pressing Ctrl + Alt + Del , as this may prevent Windows from starting up, or may cause data to be lost so that the reinstallation procedure cannot be executed.
LIMITED USE LICENSE AGREEMENT THE SOFTWARE PROGRAM(S) ("PROGRAMS") FURNISHED WITH THIS PANASONIC® PRODUCT ("PRODUCT") ARE LICENSED ONLY TO THE END-USER ("YOU"), AND MAY BE USED BY YOU ONLY IN ACCORDANCE WITH THE LICENSE TERMS DESCRIBED BELOW. YOUR USE OF THE PROGRAMS SHALL BE CONCLUSIVELY DEEMED TO CONSTITUTE YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE. Matsushita Electric Industrial Co., Ltd. ("MEI") has developed or otherwise obtained the Programs and hereby licenses their use to you.
Contrat de licence d'usage limité Le(s) logiciel(s) (les "Logiciels") fournis avec ce produit Panasonic® (le "Produit") sont exclusivement concédés en licence à l'utilisateur ultime ("vous"), et ils ne peuvent être utilisés que conformément aux clauses contractuelles cidessous. En utilisant les logiciels, vous vous engagez de manière définitive à respecter les termes, clauses et conditions des présentes. Matsushita Electric Industrial Co., Ltd.
Hard Disk Backup Function The hard disk backup function creates a backup area (storage area) on the hard disk. This area is to back up (store) hard disk contents or restore backed up contents to their original locations. By backing up the data on your hard disk to a backup area, you can protect your data from loss or damage resulting from operational errors or other factors.
NOTE Regarding backup area • Requires availability of at least half of the entire hard disk. Without sufficient space available, the backup area cannot be created. • When the backup area is created, the usable hard disk capacity will be reduced to less than half. • The backup area cannot be accessed from Windows. For this reason, backed up data cannot be copied to CD-R or other removable disk media. • When the hard disk backup function is executed, data in the backup area will be overwritten.
Hard Disk Backup Function Select [2], enter the partition size (GB), and press Enter . • You can cancel this operation by pressing 0 . • The data partition size will be the maximum settable size less the number entered above. The maximum settable size will differ depending on models. [At the time of purchase] [After the backup area is created] The usable hard disk area Can be accessed from Windows (Two partitions).
3 Select the operation to be executed from the menu. 1 Press 1 to execute [1. [Backup]]. (When dividing the hard disk into two partitions, select the backup method at next screen.) 2 At the confirmation message, press Y . The backup process will begin. 1 Press 2 to execute [2. [Restore]]. (When data is backed up in two partitions, select the restore method at next screen.
Hard Disk Data Erase Utility This computer is equipped with a utility for erasing hard disk data. When disposing of or transferring ownership of this device, erase all data on the hard disk in order to prevent the theft of hard disk data by following the steps below. The hard disk data erase utility erases data using an “overwriting” method, but there is a possibility that due to malfunctions or other operational errors, data may not be completely erased.
Specifications Main Specifications PC Card Slot Allowable current (total for two slots) RAM Module Slot*6 Microphone Jack*7 Interface Headphone Jack USB Port Modem LAN Wireless LAN Expansion Bus Connector External Antenna Connector Speaker Sound Battery Pack Operating Time* 9 Charging Time*9 Power On Power Off Clock Battery AC Adaptor*12 Power Consumption*13 Environment Operation Temperature Humidity Storage Temperature Humidity Physical Dimensions*15 (W X H X D) Weight*15 CF-18FDAZXVM CF-18GDAZXVM ® ® In
Specifications Wireless LAN (only for models with wireless LAN) Data transfer rates IEEE802.11a: 54/48/36/24/18/12/9/6 Mbps (automatically switched) IEEE802.11b: 11/5.5/2/1 Mbps (automatically switched) IEEE802.11g: 54/48/36/24/18/12/9/6 Mbps (automatically switched) IEEE802.11a/IEEE802.11b/IEEE802.11g OFDM system, DSSS system IEEE802.11a: Channels 36 to 64, 149 to 165 IEEE802.11b/IEEE802.11g: Channels 1 to 11 IEEE802.11a: 5.18~5.32 GHz, 5.725~5.825 GHz IEEE802.11b/IEEE802.
LIMITED WARRANTY For U.S.A. PANASONIC PERSONAL COMPUTERAND PERIPHERALS LIMITED WARRANTY Panasonic Computer Solutions Company (referred to as “Panasonic”) will repair this product (other than software, which is covered by a separate warranty) with new or rebuilt parts, free of charge in the U.S.A. for three (3) years from the date of original purchase in the event of a defect in materials or workmanship.
LIMITED WARRANTY For Canada PANASONIC COMPUTERAND PERIPHERALS LIMITED WARRANTY Coverage – Panasonic Canada Inc. (“PCI”) warrants to you, the first end user customer, this computer product (excluding software media), when purchased from PCI or from a PCI authorized reseller, to be free from defects in materials and workmanship under normal use, subject to the terms set forth below, during the period of warranty coverage specified.
Appendix Memo 51
As an ENERGY STAR® Partner, Matsushita Electric Industrial Co., Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Outline of the International ENERGY STAR® Office Equipment Program The international ENERGY STAR® Office Equipment Program is an international program that promotes energy saving through the use of computers and other office equipment.