PAN1762 Bluetooth Low Energy Module Product Specification Rev. 1.
PAN1762 Bluetooth Module Overview Bluetooth • 2 Mbps high-speed PHY, LE long range coded ® The PAN1762 is a Panasonic Bluetooth 5.0 Low Energy (LE) module based on the Toshiba TC35680 single-chip controller. PHY • Features • Small SMD module: 15.6 mm x 8.7 mm x 1.9 mm • Same form factor and pinout as PAN1026A and PAN1760A • • • • • • • • Bluetooth LE 5.
PAN1762 Bluetooth Module By purchase of any of the products described in this document the customer accepts the document’s validity and declares their agreement and understanding of its contents and recommendations. Panasonic reserves the right to make changes as required at any time without notification. Please consult the most recently issued Product Specification before initiating or completing a design. © Panasonic Industrial Devices Europe GmbH 2019. This specification sheet is copyrighted.
PAN1762 Bluetooth Module Table of Contents 1 2 3 4 5 6 7 About This Document......................................................................................................................... 5 1.1 Purpose and Audience .............................................................................................................. 5 1.2 Revision History ......................................................................................................................... 5 1.
PAN1762 Bluetooth Module 1 About This Document 1 About This Document 1.1 Purpose and Audience This Product Specification provides details on the functional, operational, and electrical characteristics of the Panasonic module PAN1762. It is intended for hardware design, application, and Original Equipment Manufacturers (OEM) engineers. The product is referred to as “the PAN1762” or “the module” within this document. 1.2 1.3 Revision History Revision Date Modifications/Remarks 1.
PAN1762 Bluetooth Module 2 Overview 2 Overview The PAN1762 is a Panasonic Bluetooth 5.0 Low Energy module based on the Toshiba TC35680 single-chip controller. The new Bluetooth 5.0 features enable a higher symbol rate of 2 Mbps using the high-speed 2 M PHY or a significantly longer range using the Low Energy coded PHY at 500 kb/s or 125 kb/s. The new channel selection algorithm improves the performance in environments which are busy at 2.4 GHz.
PAN1762 Bluetooth Module 2 Overview 2.1 Block Diagram PAN1762 Bluetooth Low Energy 5.0 Module 1.9 V to 3.6 V Reset Crystal 32 MHz GPIOs UART Toshiba TC35680 Crystal 32.768 kHz SPI I²C ADC Flash 128 kB Chip Antenna DC-DC Conversion SWD Product Specification Rev. 1.
PAN1762 Bluetooth Module 2 Overview 2.2 Pin Configuration Pin Assignment All dimensions are in millimeters. Top View 15.6 5.0 1.0 1.2 2.6 F1 F2 F3 0.6 F4 E1 E2 E3 E4 E5 E6 E7 E8 E9 D1 D2 D3 D4 D5 D6 D7 D8 D9 1.85 F5 F6 F7 F8 F9 1.2 F11 Ground plane keep- out area 5.0 C1 C2 C3 C4 C5 C6 C7 C8 C9 B1 B2 B3 B4 B5 B6 B7 B8 B9 A2 A3 A4 A5 A6 A7 A8 A9 F12 8.7 0.6 A1 1.35 0.6 A11 A12 1.85 3.
PAN1762 Bluetooth Module 2 Overview No Pin Name Pin Type Description A12 GND Ground Pin Connect to ground B1 GPIO9 Digital I/O B2 GPIO4 Digital I/O B3 NC NC Not connected, leave open B4 NC NC Not connected, leave open B5 GPIO7/UART RTS Digital I/O UART RTS B6 GPIO8/UART CTS Digital I/O UART CTS B7 GPIO17 Digital I/O B8 NC NC Not connected, leave open B9 GND Ground Pin Connect to ground C1 NC NC Not connected, leave open C2 NC NC Not connected, leave open
PAN1762 Bluetooth Module 2 Overview No Pin Name Pin Type Description E4 NC NC Not connected, leave open E5 NC SLPXOIN Not connected for standard version (32 kHz clock input) E6 GPIO6/UARTRX Digital Input UART RX E7 NC NC Not connected, leave open E8 GND Ground Pin Connect to ground E9 GND Ground Pin Connect to ground F1 GND Ground Pin Connect to ground F2 NC NC Not connected, leave open F3 NC NC Not connected, leave open F4 NC NC Not connected, leave open F5
PAN1762 Bluetooth Module 2 Overview 2.4 Bluetooth Features • • • • • • 2 Mbps high-speed PHY, Low Energy long range coded PHY Low Energy advertising extensions (advertising on 40 channels total) Channel selection algorithm #2 Low Energy secure connections Advertising function without CPU Wake-Up and interaction Bluetooth SIG certified Mesh stack (soon) Product Specification Rev. 1.
PAN1762 Bluetooth Module 3 Detailed Description 3 Detailed Description 3.1 Dimensions All dimensions are in millimeters. No. Item Dimension Tolerance Remark 1 Width 8.70 ± 0.35 2 Length 15.60 ± 0.35 3 Height 1.80 Product Specification Rev. 1.1 ± 0.
PAN1762 Bluetooth Module 3 Detailed Description 3.2 Footprint The outer dimensions have a tolerance of 0.35 mm. All dimensions are in millimeters. Top View 15.6 5.0 1.0 1.2 2.6 F1 F2 F3 0.6 F4 E1 E2 E3 E4 E5 E6 E7 E8 E9 D1 D2 D3 D4 D5 D6 D7 D8 D9 1.85 F5 F6 F7 F8 F9 1.2 F11 Ground plane keep- out area 5.0 C1 C2 C3 C4 C5 C6 C7 C8 C9 B1 B2 B3 B4 B5 B6 B7 B8 B9 A2 A3 A4 A5 A6 A7 A8 A9 F12 8.7 0.6 A1 0.6 Product Specification Rev. 1.1 1.
PAN1762 Bluetooth Module 3 Detailed Description 3.3 Packaging The product is an ES status product and will be delivered in the package described below. 3.3.1 Tape Dimensions 3.3.2 Packing in Tape Direction of unreeling (for customer) trailer (empty) 1 x circumference / hub (min 160mm) component packed area standard 1500pcs leader (empty) minimum 10 pitch Top cover tape more than 1 x circumference plus 100mm to avoid fixing of tape end on sealed modules.
PAN1762 Bluetooth Module 3 Detailed Description 3.3.3 Component Direction 3.3.4 Reel Dimension Product Specification Rev. 1.
PAN1762 Bluetooth Module 3 Detailed Description 3.3.5 Package Label Example (1T) (1J) (1P) (2P) (9D) (Q) (HW/SW) 3.3.6 Lot code MIC ID Customer order number, if applicable Order number Date code Quantity Hardware/software version Total Package Product Specification Rev. 1.
PAN1762 Bluetooth Module 3 Detailed Description 3.4 Case Marking Example 1 2 3 4 5 6 7 8 9 10 11 Product Specification Rev. 1.
PAN1762 Bluetooth Module 4 Specification 4 Specification All specifications are over temperature and process, unless indicated otherwise. 4.1 Default Test Conditions Temperature: Humidity: Supply Voltage: 4.2 25 °C ± 10 °C 40 % to 85 % RH 3.3 V Absolute Maximum Ratings The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. Symbol Parameter Condition Min. Typ.
PAN1762 Bluetooth Module 4 Specification 4.3 Recommended Operating Conditions The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. 4.4 Symbol Parameter Condition Min. Typ. TA Ambient operating temperature range -40 VDD 3V3 Supply voltage 1.8 Max. 3.3 Units 85 °C 3.6 V Current Consumption The current consumption depends on the user scenario, on the setup, and timing in the power modes.
PAN1762 Bluetooth Module 4 Specification 4.5 Bluetooth Parameter Condition Min. Operation Frequency Range Channel Spacing Typ. 2 402 2 480 Bluetooth LE Units MHz 2 MHz 8 dBm -95 dBm -93 dBm 500 kbps (S = 2), PER = 30.8 % at 1 500 packets with dirty Tx, 37 octets -101 dBm 125 kbps (S = 8), PER = 30.8 % at 1 500 -105 dBm Output Power Maximum setting, measured at module bottom pad Sensitivity Max. 1 Mbps, PER = 30.8 % at 1 500 packets with dirty Tx, 37 octets 2 Mbps, PER = 30.
PAN1762 Bluetooth Module 4 Specification 4.7 Recommended Soldering Profile • • • • Reflow permissible cycles: 2 • Soldering profile assumes lead-free soldering. Due to module weight, opposite side reflow is prohibited. More than 75 percent of the soldering area shall be coated by solder. The soldering profiles should be adhered to in order to prevent electrical or mechanical damage. Product Specification Rev. 1.
PAN1762 Bluetooth Module 5 Cautions 5 Cautions Failure to follow the guidelines set forth in this document may result in degrading of the module functions and damage to the module. 5.1 Design Notes 1. Follow the conditions written in this specification, especially the control signals of this module. 2. The supply voltage should abide by the maximum ratings ( 4.2 Absolute Maximum Ratings). 3.
PAN1762 Bluetooth Module 5 Cautions 5.3 Usage Condition Notes 1. Take measures to protect the module against static electricity. If pulses or transient loads (a large load, which is suddenly applied) are applied to the modules, check and evaluate their operation before assembly of the final products. 2. Do not use dropped modules. 3. Do not touch, damage, or soil the pins. 4. Follow the recommended condition ratings about the power supply applied to this module. 5.
PAN1762 Bluetooth Module 5 Cautions 1. Ensure the safety of the whole system by installing a protection circuit and a protection device. 2. Ensure the safety of the whole system by installing a redundant circuit or another system to prevent a single fault causing an unsafe status. 5.6 Other Cautions 1. Do not use the module for other purposes than those listed in section 5.3 Usage Condition Notes. 2.
PAN1762 Bluetooth Module 5 Cautions 5.7 5.7.
PAN1762 Bluetooth Module 6 Regulatory and Certification Information 6 Regulatory and Certification Information 6.1 6.1.1 Federal Communications Commission (FCC) for US FCC Notice The PAN1762 including the antennas, which are listed in 6.1.5 Approved Antenna List, complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407. The transmitter operation is subject to the following two conditions: 1.
PAN1762 Bluetooth Module 6 Regulatory and Certification Information 6.1.3 Label Requirements The OEM must ensure that FCC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic FCC identifier for this product as well as the FCC Notice above. The FCC identifier is FCC ID: T7V1762. This FCC identifier is valid for the PAN1762.
PAN1762 Bluetooth Module 6 Regulatory and Certification Information 6.1.6 RF Exposure To comply with FCC RF Exposure requirements, the OEM must ensure that only antennas from the Approved Antenna List are installed 6.1.5 Approved Antenna List. The preceding statement must be included as a CAUTION statement in manuals for products operating with the approved antennas in the previous table to alert users on FCC RF Exposure compliance.
PAN1762 Bluetooth Module 6 Regulatory and Certification Information Des informations pour les utilisateurs sur la réglementation Canadienne concernant l’exposition aux rayonnements RF sont disponibles sur le site www.ic.gc.ca. Ce produit a été développé pour fonctionner spécifiquement avec les antennes listées dans le tableau 6.1.5 Approved Antenna List, présentant un gain maximum de 1.6 dBi. Des antennes autres que celles listées ici, ou présentant un gain supérieur à 1.
PAN1762 Bluetooth Module 6 Regulatory and Certification Information 6.2.2 Labeling Requirements English Labeling Requirements The OEM must ensure that IC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic IC identifier for this product as well as the IC Notice above. The IC identifier is: IC: 216Q-1762 This IC identifier is valid for all PAN1762 modules 7.1 Ordering Information.
PAN1762 Bluetooth Module 6 Regulatory and Certification Information 6.4 European Conformity According to RED (2014/53/EU) All modules described in this Product Specification comply with the standards according to the following LVD (2014/35/EU), EMC-D (2014/30/EU) together with RED (2014/53/EU) articles: 3.1a Safety/Health: EN 62368-1:2014 EN 62311:2008 3.1b EMC: EN 301 489-1 V2.1.1:2017-02 EN 301 489-17 V3.1.1:2017-02 3.2 Radio: EN 300 328 V2.1.
PAN1762 Bluetooth Module 6 Regulatory and Certification Information Bluetooth Marks According to the Bluetooth SIG, the PAN1762 fulfills the criteria to label your product as a Bluetooth device: For further information please refer to the Bluetooth website www.bluetooth.com. 6.
PAN1762 Bluetooth Module 7 Appendix 7 Appendix 7.1 Ordering Information Variants and Versions Order Number 2 ENW89853A1KF Brand Name Description PAN1762 Bluetooth Low Energy Module 1 MOQ 1 500 1 Abbreviation for Minimum Order Quantity (MOQ). The default MOQ for mass production is 1 500 pieces, fewer only on customer demand. Samples for evaluation can be delivered at any quantity via the distribution channels. 2 Samples are available on customer demand. Product Specification Rev. 1.
PAN1762 Bluetooth Module 7 Appendix 7.2 7.2.1 Contact Details Contact Us Please contact your local Panasonic Sales office for details on additional product options and services: For Panasonic Sales assistance in the EU, visit https://eu.industrial.panasonic.com/about-us/contact-us Email: wireless@eu.panasonic.com For Panasonic Sales assistance in North America, visit the Panasonic “Sales & Support” website to find assistance near you at https://na.industrial.panasonic.
