Pamex Enkore Series A Multi-Family Door Access Control Solution Project Implementation Guide 1
Table of Contents Introduction 4 Before Installation 6 Check List 6 Pamex MFSP Service Platform 6 Implementation Guide 7 Concepts 7 Construction Phase 8 Lock Registration Phase 9 Plan your area tree 10 Build the area tree using MF-Admin Server 11 Plan your programming cards 14 Setup Wifi AP and Create Programming Cards 16 Register Locks to MF-Admin Server 19 Verify lock registration using Master Card 21 Go-live Phase 26 Create Tenant Cards 34 Create Staff Card 42 Create Ven
System Parameters 80 Mifare Card Specification 81 Card Types 82 Area Types 84 Lock Real Time Events 85 Default Severity of Alert Types 86 FCC Statement 87 NCC Statement 88 3
Introduction The Pamex Enkore series is a total solution for multi-family door access control. It not only has several models of the lock but also the browser-based central management system (MF-Admin server). Figure 1 : Pamex Enkore System Architecture Overview Figure 1 shows the system architecture of Pamex Enkore solution, Below are the brief description of each component: 1. Chrome browser: The user interface to the MF-Admin Server (2). You need a PC with a Chrome browser to use MF-Admin.
Figure 2: MP100 7. DB Server : A database is installed on windows server to keep all the data of the system. It is installed and automatically configured by the install program. Please reference MF-Admin & MP100 installation guide. 8. MFSP platform : MFSP (Multi-Family Service Platform) is a cloud service for all the MF-Admin Servers around the world. This platform is operated by Pamex. Connected your MF-Admin Server to MFSP is not required but we encourage you to do so.
Before Installation Check List ● ● ● ● ● Locks Cards : Crypto Card x 2, Construction Card x 5, Blank Card x 10 MF-Admin + MP100 Software MP100 Card Reader x 1 Windows Server x 1 Pamex MFSP Service Platform ● ● ● This section is for Pamex only. Before any Enkore installation, Pamex admin will have to create a project in MFSP in order to get the unique project code. An Enkore installation will need at least one Crypto card to activate all the locks. Crypto cards can only be issued through MFSP by Pamex.
Implementation Guide Concepts Pamex Enkore setup can be thought of in terms of three phases: Depending on the progress of your project, there are three phases defined as : ● Construction Phase : All the door locks are installed but not programmed yet. MF-Admin server is not necessary for this phase. ● Lock Registration Phase : The door locks are ready to be programmed/registered to the MF-Admin server. ● Go-Live Phase : All the locks are registered to MF-Admin Server. The system is ready to go.
Construction Phase Make sure you have Crypto Cards and Construction Cards on hand. Crypto Card and Construction Card are shipped from Pamex together with physical locks. (See Appendix: Card Types) In the scenario that wifi network and MF-Admin Server is not ready, and you have installed locks on the doors, you will need Construction Cards to unlock and open the door.
Lock Registration Phase MF-Admin Server is required to complete all the tasks in this phase. Please follow the MF-Admin Server & MP100 Installation Guide to install MF-Admin Server. MF-Admin Server is a web-based application with access controlled by login id and password. A newly installed MF-Admin Server has an admin user with login id = alzk, password = alzk.
Plan your area tree Area tree is the topology of your property. Before you can register your physical locks and link the locks to their corresponding lock place, you have to build the area tree in MF-Admin Server. There are three types of areas : group, unit, public (See Appendix: Area Types for detail). An area may contain zero or several lock places which will linked to the physical lock one by one when registering.
Build the area tree using MF-Admin Server Navigate to build area tree page. Property Management => Build Property For a brand new property, you will see only one node at beginning. Click and edit root area name. Click edit button on Root Area and select Add Public Area. Click the name text to edit public area name and lockplace name. Click menu button on Root Area and select Add Group.
Click name text to edit group name. Click menu button on Group Area M and select “Add Lock Place”. Edit lockplace name. Click menu button on Group Area M and select “Add Unit”. Click name text to edit unit name and lockplace name.
Keep adding unit from B to D Click Save To Server to save the area tree. Note that there are many ways to build an area tree as above. You may find another techniques in MF-Admin Server User Manual. If you make any mistakes during building the tree, just click “Reload from server” or “Reset” to return to the initial state.
Plan your programming cards The area tree is now ready to be linked to physical locks. Pamex Enkore locks support WPA2 encryption to connect to the Wifi AP. When a lock is scanned by a programming card, the preferred Wifi AP SSIDs will be loaded into the lock from programming card. A programming card may save 1 ~ 5 SSIDs. Normally, you only have to scan one time for a lock during its lifetime.
several cards with the same settings in order to program the locks in parallel by several workers. In the case that several workers are programming locks in parallel, please label the UID of the card (UID can be found on MF-Admin page when you create the programming card) on the programming card with a sticker or marker. When your lock is scanned, you will be able to tell which lock is yours via the UID. See the detail in registering locks.
Setup Wifi AP and Create Programming Cards Navigate to system parameters page. System Management => System Parameters Select Wifi AP Setting Click Add One to add wifi ap and click S ave to save wifi ap. Navigate to create programming cards page. Property Management => Issue Programming Key You will see there are two wifi aps you added previously.
Check the checkbox on those wifi ap and click Issue Key. Place key/card on reader first.
Click Write Key/Card to get Key’s UID. The green light LED on Read will blink. If Write Key/Card failed with three beep sounds and display following message, please re-place key/card and click Write Key/Card again.
If programming key issued successfully, two beep sounds will be made. Register Locks to MF-Admin Server Please bring a tablet or mobile phone with Chrome browser. Follow below steps to register a lock : A. Open Chrome and type in MF-Admin server URL. B. Login to MF-Admin using alzk id. C. Go to Lock Registration Monitoring function on tablet. Property Management => Lock Registration Monitor D. Go to Room A E. Scan programming card to the lock Lockplace A.
F. Link the physical lock on Room A to the lockplace. Click lock icon near Unit Area A. A pop-up window will show up listing all the locks not linked yet. Click the one you like to link. G. Link the lock to Room A lockplace. G.1. If you link to the wrong lockplace, Unlink and link again. Click lockplace which you link to the wrong lockplace. Click Unlink to unlink lock. H. Repeat the steps D to G for Lockplace B,C,D,P and M I. All set and all locks are ready for go-live phase.
Verify lock registration using Master Card Master Card is granted unlimited access to any locks in the project. After locks are registered to MF-Admin server, only Residential Cards and Master Cards can be recognized. To verify that all the locks are successfully registered and linked to the right lock places in the area tree, let’s first create the master card. ● How to create Master Card : Navigate to issue master card page.
Place key/card on reader first. Click Write Key/Card to get Key’s UID.
The green light LED on Read should blink. If Write Key/Card failed with three beep sounds and display following message, please re-place key/card and click Write Key/Card again. If master key issued successfully, two beep sounds will be made.
● How to verify Master Card to a lock : Prepare an invalid Mifare Card X(You may issue an invalid card easily by assigning wrong area to the card). By default, a lock will report to MF-Admin Server and get the newly create card list from MF-Admin Server every 5 mins(Wall Reader). It means the newly created Master Card will go to the locks after 15 mins. Another way to enforce a lock to communicate with MF-Admin server is to scan an invalid card. We will use this approach to save us some time.
○ If problem still exist, please contact your reseller for help. Please keep the Master Card safe and secure. Congratulations ! The system is ready and let’s go to Go-Live phase.
Go-live Phase We will present several daily operations when the system goes live. Most of the daily work of an administrator or property owner should be card/key management. You have seen several card types in the previous sections: Crypto Card, Construction Card, Programming Card and Master Card. Here we will create another card type called Residential Card. There are five types of Residential Card : Tenant, Staff, Vendor, Guest and Temp Card. You can tell the purpose of the card from its name.
In Time Control Templates click Create button. Edit the template name, According to the document, the Guest Swimming Pool Period only open on 8:00 ~ 18:00 Sat, 8:00 ~ 18:00 Sun. Let’s edit the time control to meet the requirement and click Save to save time control setting. Let’s create another template for house cleaning period. According to the requirement, house cleaning period only allow at 8:00 ~ 12:00 Mon.
Let’s create some user templates. We just provide basic information for demo purpose. User Type Information Tanant A Kevin Huang, kevin@alzk.com.tw Tenant B Tony Lin, lintungwei@gmail.com Tenant C Mark Chu, mark@alzk.com.tw Tenant D Jay Chen, jay@alzk.com.tw Staff S1 Peter Liu, peter@alzk.com.tw Staff S2 Ricky Chang, ricky@alzk.com.tw Vendor V Company Name : Dust Buster Employee name : Vincent Chou, vincent@gmail.com ❖ Steps to create tenants Navigate to create tenants page.
Please repeat the work and create tenant B, C, and D. ❖ Steps to create staffs Navigate to create staffs page. User Management => Staff Edit staff information and click Create Staff. The table below the input area will list all the staffs created : Follow the same process to create staff Ricky Chang. ❖ Steps to create vendors Navigate to create vendors page.
Edit vendor information and click Create Vendor. It will display vendor list below the input area. Click Employee button on Actions filed to add employee. Edit employee information and click Create New Employee The employee list will be displayed at the bottom of this page.
● Key Template Key template probably is the most useful supporting features when issue abundant keys. It is almost the same as issue a key but you may save the setting for later use. Let’s create two templates : STAFFS Public Area P (24 hours allowed), Group Area M (24 hours allowed) TENANTS Public Area P (6:00 ~ 21:00), Group Area M (24 hours allowed) ❖ Steps to create the key template Navigate to create key time control template page. Key Management => Key Template Select Create New Template.
After clicking Create button it will display Area Control page. According to the requirement, Staffs can access Public Area P (24 hours allowed), Group Area M (24 hours allowed). Let’s check the box on Public Area P and no need to edit time control because it’s 24 hours open by default. (Click on the clock besides the checkbox can edit the time control settings to this area.) Tick the checkbox on Group Area M and leave the time control settings as default.
Check the box on Public Area P and click its t ime control button. According to the requirement, Tenants can access Public Area P (6:00 ~ 21:00), Group Area M (24 hours allowed). Let’s edit the Public Area P t ime control and click Save to save time control setting. Tick the checkbox on Group Area M, no need to edit time control this time because it’s 24 hours open by default.
Click Save to save TENANTS key template. Navigate to key template management page. Key Management => Key Template You can see those key templates has been created by pull down the select list.
Card A Public Area P (6:00 ~ 21:00), Group Area M (24 hours allowed), Unit A (24 hours allowed) Card B Public Area P (6:00 ~ 21:00), Group Area M (24 hours allowed), Unit B (24 hours allowed) Card C Public Area P (6:00 ~ 21:00), Group Area M (24 hours allowed), Unit C (24 hours allowed) Card D Public Area P (6:00 ~ 21:00), Group Area M (24 hours allowed), Unit D (24 hours allowed) As you can see, leverage key template is a good idea to create the 4 tenants cards.
Click Select Tenant and it will pop up a window to display all tenants you created in user management function. Select tenant kevin to issue key. Select tenant kevin will automatically bring his information back to the Basic Information tab.
According to the requirement, tenant Kevin can access Public Area P (6:00 ~ 21:00), Group Area M (24 hours allowed), Unit A (24 hours allowed). We had already set up time control of Public Area P and Group Area M via tenant key template, so let’s check Unit A to grant access to Room A.
At the Review & Issue Key page we can verify the information of tenant key including Basic Information, Unit Area & time control information, Public Area & time control information, G roup area & time control information Click Issue/Write Key to issue tenant key.
Place key/card on reader first. Click Read Key From Reader to get Key’s UID.
The green light LED on Read should blink. If Write Key/Card failed with three beep sounds and display following message, please re-place key/card and click Write Key/Card again.
If read key successfully click Write Key/Card to issue master key. Write Key/Card successfully with two beep sounds. Repeat the similar process to create Tenant Cards for B,C and D.
Create Staff Card We will then create 2 staff cards in SIMPLE project. Again, you may use the STAFFS key template to complete this job. This time you can practice to choose the staff information from the staff users you created previously. Staff S1 Public Area P (24 hours allowed), Group Area M (24 hours allowed) Staff S2 Public Area P (24 hours allowed), Group Area M (24 hours allowed) ❖ Steps to create staff card Navigate to Issue Key page. Key Management => Issue Key Select key type as Staff.
Click Select Staff and it will pop up a window to display all staffs you created at user management. Select staff Peter to issue key. After selecting staff peter the Basic Information page will automatically attach staff’s information. Select STAFFS key template and you will see STAFFS time control settings in Area Control page. According to the requirement, staff Peter can access Public Area P (24 hours allowed), Group Area M (24 hours allowed).
At the Review & Issue Key page we can verify the information of staff key including Basic Information, Unit Area & time control information, Public Area & time control information, G roup area & time control information Click Issue/Write Key to issue Peter staff key. Place key/card on reader first.
Click Write Key/Card to get Key’s UID.
The green light LED on Read should blink. If Write Key/Card failed with three beep sounds and display following message, please re-place key/card and click Write Key/Card again Write Key/Card successfully with two beep sounds. Repeat the similar process to create S2 Staff Card..
Create Vendor Card Create a vendor card for Vincent Chou, an employee of Dust Buster cleaning company. He will come to clean the swimming pool and the area around Room A~D at 8:00 12:00 on every Monday. So we will create a card for him to enter Lockplace P and Lockplace M with time control template : House Cleaning Period. ❖ Steps to create vendor card Navigate to Issue Key page. Key Management => Issue Key Select key type as Vendor.
After selecting vendor vincent, the Basic Information page will automatically attach vendor’s information. Check the box on Public Area P and click t ime control button to edit. According to the requirement, Vendors can access at 8:00 - 12:00 on every Monday. Let’s use House Cleaning Period time control template we created before on Public Area P then click S ave to save time control setting.
Check the box on Group Area M and click time control button to edit.
Use House Cleaning Period time control template we created before on Group Area M then click Save to save time control setting.
Click Issue/Write Key to issue the vendor key. Place key/card on reader first.
Click Write Key/Card to get Key’s UID. . The green light LED on Read should blink. If Write Key/Card failed with three beep sounds and display following message, please re-place key/card and click Write Key/Card again.
Write Key/Card successfully with two beep sounds..
Create Guest/Temp Card Guest Card and Temp Card are almost the same. They serve the purpose to temporarily grant access to a visitor. The default expired date will be one day only. The one time pass attribute can be used to further restrict access to lockplace to only one time for all the lockplaces granted. Below is a demo to create a Guest Card. Create a temp card is the same. You will request the visitor to return the Guest/Temp Card when they leave the property.
Edit guest information. At Area Control page, Check the box on Public Area P and click edit time control button. Let’s assume guest August can access Public Area P on this weekend, edit time control settings and click Save to save time control setting.
Click Issue/Write Key to issue August guest key.
Place key/card on reader first. Click Write Key/Card to get Key’s UID. .
The green light LED on Read should blink. If Write Key/Card failed with three beep sounds and display following message, please re-place key/card and click Write Key/Card again. Write Key/Card successfully with two beep sounds. Shutdown Public Area The only public area we have in SIMPLE project is the swimming pool. Suppose you need to close the swimming pool in the winter or for maintenance purpose, it is not a good idea to re-issue all the cards to remove the swimming pool access right.
MF-Admin server has two features: Area Time Control and Lock Scheduling which will help you to complete this task in a second without re-issuing any cards. ● Area Time Control Area Time Control is another layer of time control which logically AND with the time control you set on the Mifare card during card creation for a specific area/lockplace. Area Time Control setting will take effect to all the residential cards (NOTE: exceptions exist if you change the access rule, we will discuss it later).
Assume the area time control of swimming pool is only for Saturday and Sunday 24 hours. Let’s edit swimming pool time control to meet the requirement, click Save to save time control setting. You can see the lock on Public Area P is blinking which means there is a time control setting over this area. ● Lock Scheduling Lock scheduling has nothing to do with Mifare card. It can be used to control the schedule to lock/unlock a lock.
Click the lock icon in Public Area P. In Operation Mode dialog, select Private and click Save. The Public Area P lock icon color will turn to light green which means it is not normal setting. As you can see in the previous screenshots, there is also a time control table which you can set when operation mode is in normal mode.
day in a weekly manner. We will not demo it here. Please see MF-Admin Server User Manual for detail.
Access Control Rule It is time to elaborate how access rules works. All the locks will apply the access rule when scan a card. Below is the default access rule settings : You have to choose one of the three settings to apply to a combination of card types and area types. The three choices are : ❖ Lock+Key : Area time control will be taken into consideration together with the settings on the card/key to decide whether lock can be unlocked or not.
System Management => System Parameters According to the document, we would want to block all users including the staff to enter swimming pool in private mode. Find out the Staff field and edit NoPrivacy to No and click Save. Now, the swimming pool has been shut down completely except Master Key.
Time Control - Add/Remove Holidays Time control settings can be found in many places in the system and it is straightforward to use. There is only one thing to remind, the holiday. In addition to the settings for 7 days a week, you have another row (the bottom row) to set time control which is the holiday setting. For system to recognize which days are holiday, you have use the application parameters function to add/remove holidays.
Click Save to save the holiday. ❖ Remove holiday Click X to remove holiday and click Save. The holiday setting takes precedence over weekly settings. It means if today is a holiday and Monday, then the system will check holiday’s settings instead of Monday’s settings.
Advanced Setup Guide Note : Do not try this section without assistance from reseller or Pamex. Changing any of the parameters in this section to unreasonable value might lead to unexpected system behavior. Lock Report Interval Lock report interval can be changed at the Lock Operation function. The default value of this parameter is 300 secs (5 mins) for Wall reader and 900 secs (15 mins) for deadbolt and leverset.
Click lock icon to select lockplace Public Area P (multiple selections is allowed), at Set Lock Parameters (j0) field find out Report Interval parameters and set up it to 30 mins. Click Schedule Job to change the report interval setting. To save the battery’s life, Pamex Enkore smart lock is not always connected to MF-Admin Server. The locks will connect to the MF-Admin Server as the report interval.
When you login the MF-Admin Server, there are two icons showing the total number of new alerts at the navigation bar : In the Alert tab of the system parameters, you can see there are twelve types of alert that will be generated in the system: There is no alert enabled by default. You may check the checkbox to enable the alerts you need. You may enter valid email addresses in the “Send Email To” field to enable email notification for an alert. Multiple addresses can be entered delimited by semicolon.
Appendix Lock UI Patterns (LED & Buzzer) Leverset & Deadbolt 第一次換電池 (Recovery Card後) Beep一聲紅燈亮, 馬達校正, 紅綠交替一次,, 完成後鎖舌伸出, Beep 一聲紅燈閃 非第一次換電池 Crypto Card 紅燈亮, beep一聲, 紅綠交替兩次, beep一聲, 不作馬達校正. 鎖 舌不動. 綠燈亮, 長beep 刷卡開門 Beep一聲, 綠燈亮, 鎖舌收 刷卡鎖門 非法卡 Beep一聲, 紅燈亮, 鎖舌出 紅燈閃三次, Beep三聲 紅燈間隔一秒閃一次, 持續一分鐘(預設) - (同開關門) 綠燈閃兩次 beep 兩聲.
弱電處理 斷電處理 之後刷卡可正常鎖門 鎖在每次運作後, 餘600次開關電力時 : 紅燈每10秒閃一次, 持續1分鐘 餘400次開關電力時 : 紅燈每5秒閃一次, 持續1分鐘 餘200次開關電力時 : 紅燈每2秒閃一次, 持續1分鐘 餘待機電力3個月, 可支援一次刷卡開門電力 Leverset & Deadbolt Change the battery (the first time after tapping a recovery card) Change the battery a beep with a red blink + motor adjustment + a red blink + a green blink(finished with a latch appear) + a beep with a red blink Crypto Card Tap to lock A red blink with a beep + a red blink + a green blink + a red blink + a green blink + a beep (No motor adjust
card) Lock Out connect with the APs. Red blinks for 3 mins as a default Key cover open 10 red blinks + 10 beeps Malfunction when tapping to unlock the latch jammed, the motor rotate continuously with 3 red blinks + 3 beeps, failed to try after 30 secs, be able to open the door by tapping the card. the latch jammed, the motor rotate continuously with 3 red blinks + 3 beeps, failed to try after 30 secs, be able to lock the door by tapping the card.
Lock Out 閉鎖 紅燈亮三分鐘(預設) Wall Reader Crypto card a green blink with a long beep. Tap to lock a green blink with a beep. Tap to unlock Invalid card a red blink with a beep. 3 red blinks with 3 beeps Red blinks between seconds lasting 1 minute as a default.(Lock Out) Construction Card (same as lock/unlock) Programming Card 2 green blinks with 2 beeps. Red blinks continuously till a success connect with AP along with a green blink + a long beep.
Wifi AP Specification and Settings Wifi network is necessary for Pamex Enkore solution. The network setup is out of the scope of this manual. Please make sure your network is well configured with your system vendors. Pamex Enkore locks support most of the popular wifi APs in the market. Please make sure your Wifi AP has the features listed below : ● ● Support 802.11 bgn, 2.
Factory default settings - Wall Reader ● ● ● ● Model No:KA-WR1S/KA-WR1N Operation Mode:Normal Lock Parameters a. Volume:3 (high) b. Enabled Locking Mode:Auto lock c. Auto Lock Delay:10 secs d. Report Interval:300 secs Lockout Settings a. Time to count fail(secs):60 b. Fail Try(times):3 c.
Factory default settings - Deadbolt ● ● ● ● Model No: a. D1:KA-D7P1S b. D2:KA-D7P1A Operation Mode:Normal Lock Parameters a. Volume:3 (high) b. Enabled Locking Mode: ■ D1:Auto reset turnpiece ■ D2:Scan lock c. Auto Lock/Reset Turnpiece Delay (secs) ■ D1:5 ■ D2:N/A d. Report Interval:900 secs Lockout Settings a. Time to count fail(secs):60 b. Fail Try(times):4 c.
Factory default settings - Leverset ● ● ● ● Model No:KA-LNP5C Operation Mode:Normal Lock Parameters a. Volume:3 (high) b. Enabled Locking Mode:Auto lock c. Auto Reset Turnpiece Delay(secs):5 d. Report Interval:900 secs Lockout Settings a. Time to count fail(secs):60 b. Fail Try(times):4 c.
Factory default settings - Interconnect ● ● ● ● Model No: a. I1:KA-INP35S b. I2:KA-INP35A Operation Mode:Normal Lock Parameters a. Volume:3 (high) b. Enabled Locking Mode: ■ I1:Auto reset turnpiece ■ I2:Scan lock c. Auto Lock/Reset Turnpiece Delay (secs) ■ I1:5 ■ I2:N/A d. Report Interval:900 secs Lockout Settings a. Time to count fail(secs):60 b. Fail Try(times):4 c.
MF-Admin Server Parameters default settings Application Parameters Please see MF-Admin Server User Manual. System Parameters Please see MF-Admin Server User Manual.
Mifare Card Specification You may purchase Mifare Card or Key fob from 3rd party. MIFARE® is the N XP Semiconductors-owned trademark of a series of chips widely used in contactless smart cards and proximity cards. The MIFARE® brand name covers proprietary solutions based upon various levels of the ISO/IEC 14443 Type A 13.56 MHz contactless smart card standard. It incorporates AES and DES/Triple-DES encryption standards, as well as an older proprietary encryption algorithm.
Card Types Pamex Enkore defines below card types : Card Type 1 Crypto Card (CRC) 2 Construction Card (COC) 3 Programming/Registration Card (PRC) 4 Residential Card (RSC) – sub-typed into five different residential card : Tenant card, Staff card, Vendor card, Guest card, and Temp card depending how you issue the card using MF-Admin server 5 Master Card (MAC) Crypto Card : To recognize any other types of card, a lock has to read Crypto card. Crypto card is not issued from MF-Admin server.
Master Card is an unrestricted access card to any door locks in the project. It is created using MF-Admin server. Master Card is only valid to the locks which has registered to MF-Admin server.
Area Types There are three types of area you may create in MF-Admin Server : Group Area : Group area is like a folder. It is used to group together the units and public areas in the same floor/building for example. Unit Area : An unit area represents an unit for one family. Public Area : A public area represents a shared facility like swimming pool. These areas will be organized into a single root area tree to represent your property.
Lock Real Time Events 1. Battery Change 2. Battery Low 3. Card space 90% full 4. Card# limitation reached 5. Firmware upgrade completed 6. Force to Normal 7. Invalid Key 8. Key Cover Open 9. Lock Out 10. Lock Schedule activated by staff 11.
Default Severity of Alert Types No.
FCC Statement FCC Statement: Enkore KE1-LNP5C(FCC ID:2AQ8A-KE1LNP5C), Enkore KA-WR1N(FCC ID:2AQ8A-KAWR1N), Enkore KA-WR1S(FCC ID:2AQ8A-KAWR1S) compile with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)Enkore KE1-LNP5C, Enkore KA-WR1N, Enkore KA-WR1S may not cause harmful interference, and (2)Enkore KE1-LNP5C, Enkore KA-WR1N, Enkore KA-WR1S must accept any interference received, including interference that may cause undesired operation.
NCC Statement NCC Statement: Taiwan Regulatory Information(NCC) 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加 大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用 ，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 88
