9680202_oipm_En011_9640915.01 03/21/18 Page 1 Operating Instructions & Parts Manual Model 9680202 8˝ Drill Press 9640915.
NORSE Operating Manual & Parts List Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! retain instructions for future reference. ASSEMBLY / INSTALLATION OPERATION TROUBLESHOOTING MAINTENANCE / REPAIR 9680202 Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
9680202_oipm_En011_9640915.01 03/21/18 Page 3 GETTING STARTED Save This Manual Structural Requirements Ensure all supporting structures and load attaching devices are strong enough to hold the intended loads. If in doubt, consult a qualified structural engineer. Electrical Requirements Tools Needed: Standard mechanic’s hand tool set (i.e. hammer, screwdrivers, adjustable wrenches, etc.). UNPACKING When unpacking, check to make sure all parts listed below are included.
OPERATION ASSEMBLY / INSTALLATION SAFETY / SPECIFICATIONS GETTING STARTED 9680202_oipm_En011_9640915.01 03/21/18 Page 4 NORSE Operating Manual & Parts List SAFETY RULES CONTINUED • • • Prepare Work Area for Job • • • • • Keep work area clean. Cluttered areas invite injuries. Observe work area conditions. Do not use machines or power tools in damp or wet locations. Do not expose to rain. Keep work areas well lighted.
9680202_oipm_En011_9640915.01 03/21/18 Page 5 ASSEMBLY Tools Needed for Entire Assembly • Adjustable wrench • Screwdriver • Hammer with block of wood or rubber hammer 9680202 INSTALLATION All electrical connections must be performed by a qualified electrician. Power Source 2. Set the column on the base, making sure to line up the three holes in both the base and column. Grounding Instructions 1. Place the base on a stable surface (either on a sturdy table or the floor) 3.
MAINTENANCE / REPAIR TROUBLESHOOTING OPERATION ASSEMBLY / INSTALLATION SAFETY / SPECIFICATIONS GETTING STARTED 9680202_oipm_En011_9640915.01 03/21/18 Page 6 NORSE Operating Manual & Parts List OPERATION Starting and Stopping the Drill 9680202 2. To tilt the work table, loosen the table bolt/nut on the underside of the table and tilt to desired angle up to 45° and retighten. Be sure drill bit is not in contact with workpiece when starting the motor.
9680202_oipm_En011_9640915.01 03/21/18 Page 7 9680202 TROUBLESHOOTING GUIDE Symptom Noisy operation Excessive drill run out or wobble 1. Bent bit 2. Bit not properly installed in chuck 3. Chuck not installed properly 4. Worn spindle bearings 1. Workpiece pinching bit or excessive feed pressure 2. Improper belt tension 3. Workpiece not supported or clamped properly 1. Adjust tension 2. Lubricate spindle (see Maintenance, page 6) 3. Tighten pulley nut 4. Tighten set screw in pulley 1. Change speed 2.
NORSE Operating Manual & Parts List REPAIR PARTS ILLUSTRATION FOR 9680202 8˝ DRILL PRESS MAINTENANCE / REPAIR TROUBLESHOOTING OPERATION ASSEMBLY / INSTALLATION SAFETY / SPECIFICATIONS GETTING STARTED 9680202_oipm_En011_9640915.
680202_oipm_En011_9640915.01 03/21/18 Page 9 9680202 REPAIR PARTS LIST FOR 9680202 8˝ DRILL PRESS Ref. No. Description 5 1 1 1 2 1 1 1 1 5 2 1 5 2 1 1 1 1 1 4 1 1 2 1 2 1 1 1 1 1 2 2 1 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 53 54 55 56 57 58 59 60 61 62 64 65 70 73 ∆ Hex nut 10mm Pointer Stop rod 10 x 1.5mm Switch box Switch plate Philips screw ST4.
MAINTENANCE / REPAIR TROUBLESHOOTING OPERATION ASSEMBLY / INSTALLATION SAFETY / SPECIFICATIONS GETTING STARTED 9680202_oipm_En011_9640915.
9680202_oipm_En011_9640915.
9680202_oipm_En011_9640915.01 03/21/18 Page 12 NORSE Operating Manual & Parts List 9680202 NORSE Warranty NORSE by C.H. Hanson warrants their products to be free of defects in material or workmanship. This warranty does not cover defects due directly or indirectly to misuse, abuse, normal wear and tear, failure to properly maintain the product, heated, ground or otherwise altered, or used for a purpose other than that for which it was intended. The warranty does not cover expendable and/or wear part (i.