User's Manual

ManualsBrandsPAC International ManualsElectronicsPAC-VN

Page 1

INTERNATIONAL

Data Sheet

Vandal Multi-Output Format Proximity Reader

Operation and Installation Instructions

Features Description

The KeyPAC Vandal (PAC Part Number 20450 or K3002) proximity reader is an accessory

commonly used on a majority of access control systems. The Vandal uses pre-encoded ISO

proximity cards (PAC Part Number 21030). Each card is encoded with a unique code that outputs

a serial number to the access control system.

The reader is weather resistant and suitable for indoor or outdoor use. Cards are read at a

distance of up to 3 inches.

This reader is also available in brass finish by ordering PAC Part Number 20458 or K3002B.

How the Reader is Used

The Vandal is connected to a reader input on a door controller, time and attendance unit or control

panel, that can accept a PAC format, Wiegand 26/ 32/ 64 Bit format or ANSI Magstripe format.

The reader detects and reads the unique embedded coding from each ISO card when it is

presented within 3 inches of the reader. The reader will then output this coding, that has been

received by the card, to the receiving door controller, time and attendance unit or control panel.

How the Reader Operates

The reader has an LED to indicate status. When the reader's LED is red the reader is ready to

read a card and output the coding to the control panel. When a valid card is read the output will

begin sending the information to the control panel. If the card is valid, the control panel will activate

and output to the reader turning the LED to green. This change of the LED will most commonly

indicate a Access Granted condition or an acknowledgment that the control panel has received and

logged the coding from the card.

•

Easy Installation

•

Reads ISO Cards (PAC P.N. 21030)

•

Status LED indicates Access Authorised

•

Rated for Indoor and Outdoor use

•

Stainless Steel Housing

Summary of content (5 pages)

PAGE 1
INTERNATIONAL Data Sheet Vandal Multi-Output Format Proximity Reader Operation and Installation Instructions Features Description • Easy Installation • Reads ISO Cards (PAC P.N. 21030) • Status LED indicates Access Authorised • Rated for Indoor and Outdoor use • Stainless Steel Housing The KeyPAC Vandal (PAC Part Number 20450 or K3002) proximity reader is an accessory commonly used on a majority of access control systems. The Vandal uses pre-encoded ISO proximity cards (PAC Part Number 21030).
PAGE 2
Items Included with the Vandal 1 Vandal Proximity Reader 4 1 1 10 No. 8 VR Screws Label Metal Oxide Varistor (to wire across the lock) Crimp Connectors Connecting the Reader to the Control Panel or Wiegand Interface Unit Connect the reader to the Door Controller, Time and Attendance unit or Control Panel as described in the Operation and Installation Manual provided with the corresponding unit. Use five wires, six wires if tamper is used, to connect the Vandal reader to the controlling unit.
PAGE 3
Installing the Reader Choose the Best Mounting Location for the User The normal height for the reader is approximately 48 inches (four feet) from the floor, on the unhinged side. Check local regulations regarding proper mounting locations for disabled or handicapped persons. Mount the reader on any firm flat surface. Avoid mounting the reader on rough textured surfaces. There must be a distance of at least 36 inches (three feet) between two readers.
PAGE 4
Mounting the Reader This reader should be mounted using the Vandal Resistant screws provided. You will need the special screwdriver for these screws (Part no. 1950 - available separately). Fixing the Reader 1. Ensure that the reader cable is not connected to the controller. Route the flying lead behind the reader and connect it using the crimp connectors supplied. Wire the cable as described in the Wiring section later in this manual. 2.
PAGE 5
Reader Operation Normal Operation and LED Control The reader LED will normally be red when the door or system is in the closed condition. When a card is presented within range of the reader the code in the card will be read and the coding sent to the controlling unit. If the card is valid for that door or system at that time the LED will go green which is controlled by the N.O. relay or LED connection of the Control Panel. The LED will stay green while the Brown LED wire is shorted to Common.