User's Manual

ManualsBrandsPAC International ManualsElectronicsKeyPAC Slimline Reader

Page 1

INTERNATIONAL

Data Sheet

Slimline Multi-Output Format Proximity Reader

Operation and Installation Instructions

Features Description

The KeyPAC Slimline (PAC Part Number 20457) proximity reader is an accessory commonly used

on a majority of access control systems. The Slimline uses pre-encoded ISO proximity cards (PAC

Part Number 21030). Each card is encoded with a unique code that outputs a serial number to the

access control system.

The Slimline is weather resistant and suitable for indoor or outdoor use. Cards are read at a

distance of up to 3 inches.

This reader is also available in off-white by ordering PAC Part Number 20451.

How the Reader is Used

The Slimline is connected to a reader input on a door controller, time and attendance unit or control

panel, that can except a PAC format, Wiegand 26/ 32/ 64 Bit format or ANSI Magstripe format.

The Slimline detects and reads the unique embedded coding from each ISO card when it is

presented within 3 inches of the reader. The Slimline will then output this coding, that has been

received by the card, to the receiving door controller, time and attendance unit or control panel.

How the Reader Operates

The Slimline has an LED to indicate reader status. When the reader's LED is red the reader is

ready to read a card and output the coding to the control panel. When a valid card is read the

output will begin sending the information to the control panel. If the card is valid, the control panel

will activate and output to the Slimline turning the LED to green. This change of the LED will most

commonly indicate a Access Granted condition or an acknowledgment that the control panel has

received and logged the coding from the card.

•

Easy Installation

•

Reads ISO Cards (PAC P.N. 21030)

•

Status LED indicates Access Authorised

•

Rated for Indoor and Outdoor use

•

Offered in Dark Grey or Off-White Colors

•

Outputs in PAC Output Format, Wiegand 26, 32, 64 Bit

Format, ANSI Magstripe

Summary of content (6 pages)

PAGE 1
INTERNATIONAL Data Sheet Slimline Multi-Output Format Proximity Reader Operation and Installation Instructions Features Description • Easy Installation • Reads ISO Cards (PAC P.N.
PAGE 2
Items Included with the Slimline 1 1 1 10 Slimline Proximity Reader Reader Front plate Metal Oxide Varistor (to wire across the lock) Crimp Connectors Connecting the Slimline to the Control Panel or Wiegand Interface Unit Connect the Slimline to the Door Controller, Time and Attendance unit or Control Panel as described in the Operation and Installation Manual provided with the corresponding unit. Use five wires, six wires if tamper is used, to connect the Slimline reader to the controlling unit.
PAGE 3
Installing the Reader Choose the Best Mounting Location for the User The normal height for the reader is approximately 48 inches (four feet) from the floor, on the unhinged side. Check local regulations regarding proper mounting locations for disabled or handicapped persons. Mount the reader on any firm flat surface. Avoid mounting the reader on rough textured surfaces. There must be a distance of at least 36 inches (three feet) between two readers.
PAGE 4
Mounting the Reader The reader consists of two parts, the reader itself (with a flying lead) and a snap-fit cover. Fixing the Reader 1. Ensure that the reader cable is not connected to the controller. Route the flying lead behind the reader and connect it using the crimp connectors supplied. Wire the cable as described in the Wiring section later in this manual. 2. If the connections are in a location that may be wet or damp, then protect the connectors with a sealing compound, or use weatherproof crimps.
PAGE 5
WARNING: For Output formats other than PAC, the output format of the reader will be reprogrammed for a PAC system if the White and Brown wires are shorted and power is applied to the reader. The reader will need to be sent in for repair to have the output format reset once this has occurred. Tamper Operation The Blue wire tamper connection is a normally closed circuit between the blue wire and black wire common connection.
PAGE 6
Specification Dimensions 5.12in x 1.58in x 0.59in Voltage 10.5v DC to 20v DC (supplied by Door Controller, Wiegand Interface or Control Panel) Current Idle: Reading: 15-25mA 15-25mA Temperature: Operating Storage -10C to +55C (14ºF to 130ºF) -30C to +80C (-20ºF to 175ºF) Humidity: Operating 0-90% RH at 30C ±2C (85ºF±5ºF) for 24 hours Reading Range: 0-3 inches Lead Length: 36 inches This device complies with part 15 of the FCC rules.