User's Manual

ManualsBrandsPAC International ManualsElectronicsLow range proximity reader

17413 v1.0

Document No. nnnnnnn (c) PAC 2000. Confidential

PAC International Ltd.

Low Profile DualTech Reader

Installation Instructions

Part Numbers 20467 (Black) and 20473 (White)

Introduction

The PAC Low Profile DualTech Reader is a proximity reader. This means that no physical contact

is required between the ID device and the reader for the ID device to be read. It usually works with

a door controller to control access through a door. In this case, to open a door, an ID device is

presented to the reader, the reader passes the code to the door controller, and the door controller

validates the code and unlocks the door.

DualTech

PAC produces two categories of ID device, PAC and KeyPAC series format, these are based on

different reading technologies. Readers are available which read either just PAC Format format or

just KeyPAC Format format, however, the PAC DualTech reader is capable of reading both.

Compatible ID Devices

This reader can read PAC and

KeyPAC Format ID-devices.

Summary of content (6 pages)

PAGE 1
P AC In t e r n a t i o n a l Lt d . Low Profile DualTech Reader Installation Instructions Part Numbers 20467 (Black) and 20473 (White) Introduction The PAC Low Profile DualTech Reader is a proximity reader. This means that no physical contact is required between the ID device and the reader for the ID device to be read. It usually works with a door controller to control access through a door.
PAGE 2
This manual is correct at the time of going to press. However, as part of our ongoing product enhancement program we reserve the right to make changes to the product and/or literature at any time without prior notice to the customer. Unpacking Check that all the parts are supplied with your reader. If anything is missing or damaged, contact your suppliers immediately. The readers are each supplied with the following: 2 x 1” no.
PAGE 3
Fixing the Reader 3.28” 0.64” 0.32” 1.28” 0.16” 0.4” 0.16” 1.4” 3.8” 0.16” 0.4” 0.4” 0.32” 1.4” 1.08” 1.08” 0.4” 1.28” 0.16” 0.72” Reader Mounting Plate This reader comes in two parts, the reader itself and the backplate. The backplate has a rubber spacer at the rear. Fixing the Reader 1. The cable from the controller should be routed through the aperture in the backplate. Leave enough cable exposed to allow easy wiring of the reader.
PAGE 4
Wiring All connections are made to the flying lead using the 10 cable crimps provided. Cable gauge depends on distance from the Door Controller to Reader. The flying lead is 3 ft (1m) long and has 2 a gauge 24AWG (0.22mm ). 2 With 24AWG (0.22mm ) cable twist the wires and double them over before inserting them in the crimps. This includes the flying lead. Flying Lead PAC Black GND White SIG Green Not Used Brown VCA/LED Yellow Red SOUNDER – GND to activate 12V DC (+10.
PAGE 5
MOV - Lock Suppression A metal-oxide-varistor (MOV) is provided with each reader although it is used to protect the door controller. It prevents high voltage spikes (back e.m.f.s) being returned from the lock unit to the door controller. High voltage spikes can cause erratic operation and eventually severe damage to the door controller if not controlled. CAUTION: Failure to install the MOV at the lock will result in early failure of the door controller. It will also invalidate the warranty.
PAGE 6
Specification Other important features include: • Integral red/green LED • Tamper protection • Integral sounder Dimensions See installation diagram. Approximate Reading Range KeyPAC Format: up to 3.2 inches (80mm) PAC Format: up to 1.6 inches (40mm) Note: These ranges will reduce if the readers are exposed to local sources of electrical noise. Power Requirements Voltage 12V DC (nominal), tolerance +10.5 to +20V.