User Manual

ManualsBrandsPAC International ManualsElectronicsLow range proximity reader

Data Sheet

January 2003 15729 Ver 1.5 DRAFT D

PAC Portico, 1 Lower Ragsdale Drive, Building 3, Suite 800, Monterey, California 93940 USA

www.PACPortico.com

This document is correct at the time of going to press. However, as part of our ongoing product enhancement program

we reserve the right to make changes to the product and/or literature at any time without prior notice.

PAC Readers

Low Profile, Vandal Resistant and Panel Mount

2001 Low Profile Reader-Black

2001W Low Profile Reader-White

2002 Vandal Resistant Reader-Steel

2002W Vandal Resistant Reader-Brass

2025 Panel Mount Reader

CAUTION

These readers should only be used with systems that

use PAC ID keys. For example, they should not be

connected to an Easikey controller.

Low Profile Vandal Resistant Panel Mount

Items Enclosed

Low profile reader Vandal resistant reader Panel mount reader and head

4 terminal screws 4 terminal screws 4 terminal screws

MOV MOV MOV

Mounting backplate 4 x 1¼" No. 8 VR screws Lexan window and backplate

Label

2 x 1" No.6 self-tapping

screws

A special screwdriver

(available separately) is

required for the Vandal

Resistant (VR) screws.

Note

The readers come with a 6-wire suppression lead that should be installed as described in

this datasheet. This cable must be installed to comply with CE regulations.

Dimensions

H x W x D in/mm

3.94/100 x 3.46/88 x 0.47in/12

H x W x D in/mm

3.94/100 x 3.94/100 x 0.47/(12

H x W x D in/mm

3.62/92 x 2.44/62 x 0.59/15 Reader

2.36/60 x 2.36/60 x 0.47/12 Head

Maximum Reading Range

2in/50mm 0.4in/10mm 0.4in/10mm

Summary of content (6 pages)

PAGE 1
Data Sheet January 2003 15729 Ver 1.5 DRAFT D PAC Readers Low Profile, Vandal Resistant and Panel Mount Low Profile Reader-Black Low Profile Reader-White Vandal Resistant Reader-Steel Vandal Resistant Reader-Brass Panel Mount Reader 2001 2001W 2002 2002W 2025 Low Profile CAUTION These readers should only be used with systems that use PAC ID keys. For example, they should not be connected to an Easikey controller.
PAGE 2
15729 Ver 1.5 DRAFT D PAC Readers Low Profile, Vandal Resistant and Panel Mount Installation CAUTIONS 1. The readers should not be mounted on metal. 2. The cable distance from controller to reader should not exceed the cable distance quoted in Section 0. 3. If using a Request to Exit switch, ensure that the wiring is not accessible if the reader is removed. 4. Ensure that the LED is always visible to the key holder. 5.
PAGE 3
PAC Readers Low Profile, Vandal Resistant and Panel Mount 15729 Ver 1.5 DRAFT D Removing the Reader The reader can be removed from the backplate by placing a small flat-bladed screwdriver into the apertures on each side of the backplate. Take care not to damage the reader or backplate. Vandal Resistant Readers This reader should be mounted using the vandal resistant screws provided. Note A special screwdriver (not supplied) is required to use these screws. Mounting the Reader 1.
PAGE 4
15729 Ver 1.5 DRAFT D PAC Readers Low Profile, Vandal Resistant and Panel Mount Panel Mount Reader This reader is designed to be mounted in a steel panel (E) such as used in a door-entry system. There are two main units; the main module, a black rectangular unit, connected by a fixed length of cable to a reading head. The cable between the two parts is fixed, 24in/60mm long and should not be cut, extended or shortened. Panel Aperture The reading head is designed to fit a 1.57in/40mm square hole.
PAGE 5
PAC Readers Low Profile, Vandal Resistant and Panel Mount 15729 Ver 1.5 DRAFT D Reader Wiring Notes 1. The wiring and location of readers is described in the documentation supplied with the door controller. All the readers described in this datasheet have identical terminals. 2. If connected to a PAC 2100 Series Door Controller, it is strongly recommended that a 100mA in-line fuse is installed in line with the reader supply.
PAGE 6
15729 Ver 1.5 DRAFT D PAC Readers Low Profile, Vandal Resistant and Panel Mount MOV - Lock Suppression A Metal-Oxide-varistor (MOV) is provided with each reader. This device prevents back EMF ('spikes') being returned from the electric lock to the controller. This can cause severe damage over a period of time, and erratic operation of the system if not controlled. A B The MOV (A) should be installed across the power terminals of the lock (B).