User Manual

ManualsBrandsPAC International ManualsElectronicsLow range proximity reader

DATASHEET

PAC INTERNATIONAL LTD, 1 Park Gate Close, Bredbury, Stockport, SK6 2SZ, England

Tel: +44 (0) 161 406 3400. Fax: +44 (0) 161 430 8658

www.pac.co.uk

Easikey Readers

Mullion, Vandal Resistant and Panel Mount

17063 Ver 1.6 DRAFT B January 2003

20377 Mullion Reader-Black

20387 Mullion Reader-White

20378 Vandal Resistant Reader-Steel

20388 Vandal Resistant Reader-Brass

20421 Panel Mount Reader

CAUTION

These readers are suitable for connection to

Easikey and Easikey 1000 only. They should

not be connected to any other type of

equipment (e.g. PAC 2100/2200 series).

1. Introduction

Mullion Vandal Resistant * Panel Mount *

Items Enclosed

Mullion reader Vandal resistant reader Panel mount reader and head

4 terminal screws 4 terminal screws 4 terminal screws

MOV MOV MOV

Mounting backplate 4 x 1¼" No. 8 VR screws Lexan window and backplate

Label

2 x 1" No.6 self-tapping

screws

A special screwdriver

(available separately) is

required for the Vandal

Resistant (VR) screws.

Note

The readers come with a 6-wire suppression lead that should be installed as described in

this datasheet. This cable must be installed to comply with CE regulations.

Dimensions

H x W x D mm

83 x 3.38 x 12

H x W x D mm

100 x 100 x 12

H x W x D mm

92 x 62 x 15 Reader

60 x 60 x 12 Head

Maximum Reading Range

25mm 8mm 8mm

Summary of content (8 pages)

PAGE 1
DATASHEET Easikey Readers Mullion, Vandal Resistant and Panel Mount 17063 Ver 1.6 DRAFT B January 2003 Mullion Reader-Black Mullion Reader-White Vandal Resistant Reader-Steel Vandal Resistant Reader-Brass Panel Mount Reader 20377 20387 20378 20388 20421 CAUTION These readers are suitable for connection to Easikey and Easikey 1000 only. They should not be connected to any other type of equipment (e.g. PAC 2100/2200 series). 1.
PAGE 2
Introduction Specification for all readers Operating Temperature: -40C to +50C Current: 90mA (maximum) Supply Voltage: 9-16v DC (supplied by the controller) Cable Type: 4 or 6-conductor, multi-stranded, unscreened Cable Distances: Up to 100m from controller using 7/0.2 (0.
PAGE 3
Installation 2. Installation 2.1 Mullion Reader - Installation 4 10 3 38 12 84 A 60 12 B This reader comes in two parts, the reader itself (A) with 4 terminals and the backplate (B). The backplate has a 3mm rubber spacer at the rear. 2.1.1 Fixing the Reader 1. The cable from the controller should be routed through the aperture in the backplate. Leave enough cable exposed to allow easy wiring of the reader (at least 20mm). Note There is limited room between the reader and backplate.
PAGE 4
Vandal Resistant Reader - Installation 3. Vandal Resistant Reader - Installation 100 70 12 5 70 100 5 This reader should be mounted using the Vandal Resistant screws provided. Note A special screwdriver (not supplied) is required to use these screws. 3.1 Fixing the Reader The cable from the controller should come to the rear of the reader. Leave enough cable exposed to allow easy wiring of the reader (at least 20mm). Note The terminals protrude 5mm from the rear of the reader.
PAGE 5
Panel Mount Reader - Installation 4. Panel Mount Reader - Installation E A B C D 60 48 4 14 60 42 F G 60 40 70 90 15 60 This reader is designed to be mounted in a steel panel (E), such as used in a door-entry system. There are two main units; the main module, a black rectangular unit, connected by a fixed length of cable to a reading head. The cable between the two parts is fixed, 60mm long and should not be cut, extended or shortened. 4.
PAGE 6
Reader Wiring 5. Reader Wiring 5.1 General Tips • The cable distance from controller to reader should never exceed 100m. • If using a Request to Exit switch, ensure that the wiring is not accessible if the reader is removed. • Ensure that the LED is always visible to the keyholder. Note The wiring and location of readers is fully described in the documentation supplied with the controller. All the readers described on this sheet have identical terminals.
PAGE 7
Reader Wiring Notes 1. The ends of any cores not used on the suppression cable can be snipped off. 2. If the controller is an Easikey then there is no Door Contact option available and the Brown core on the suppression cable is not used. 5.3 MOV - Lock Suppression A metal-oxide-varistor (MOV) is provided with each reader. This device prevents back e.m.f. ('spikes') being returned from the electric lock to the controller.
PAGE 8
Reader Wiring Declaration of Conformity Application of Council Directives 73/23/EEC Standard(s) to which conformity is declared ETS 300.683 Manufacturer's Name PAC INTERNATIONAL LTD Manufacturer's Address 1 Park Gate Close, Bredbury, Stockport, U.K. SK6 2SZ Type of Equipment Access Control Systems Product Equipment Easikey Reader Range I, the undersigned, hereby declare that the equipment specified above conforms to the above directive(s) and standard(s). Signed Full Name 17063 Ver 1.