Kill A Watt™ EZ .................................................................................... Operation Manual P4460 KILL A WATT EZ TM P.F.
Thank you for purchasing the P4460 Kill A Watt™ EZ Power Meter. This operating manual will provide an overview of the product, safety instructions, a quick guide to operation, and complete instructions for correct usage. Take the time to completely review these instructions as well as all safety warnings to ensure your best use of the product.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Water and Moisture – Do not use this product near water – for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool and the like. Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Any mounting of the product should follow the manufacturer’s instructions.
Object and Liquid Entry – Never push objects of any kind into this product through openings (if any) as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Quick Start Guide: Use these quick start instructions to get up and running in just a few minutes. Be sure to review all the operating instructions later to ensure full enjoyment of the product. 1. Connect the Kill A Watt™ EZ unit to the outlet and the appliance to the unit 2. Press and hold the RESET key on the unit until “rESt” appears. 3. Press and hold the SET rate key until “Rate” is displayed and the currently set rate flashes. 4. Press the UP and DOWN key to set your desired rate.
Installation: 1. Remove the protective film (if any) covering the LCD meter display by pulling the tab marked “REMOVE BEFORE USE”. 2. Turn off the appliance and remove the power cord from the outlet. Connect the Kill A Watt™ EZ unit to the outlet and the appliance to the unit. If the outlet is in an inconvenient location first connect a quality extension cord that is rated for the application. 3. Turn the appliance back on and confirm normal operation.
ance since the last reset. This cost is calculated based on the total consumed power in KWH and the utility rate that you have set. 3. Don’t be surprised if the total cost display is 0.00 initially. It will take some time to accumulate cost. 4. Pressing the UP and DOWN key will cycle through the cost projection periods. “Hour”, “Day”, “Week”, “Month”, and “Year” will display on the LCD to indicate the selected period.
LCD can display meter readings such as Volts, Current, Watts, Frequency, Power Factor, and VA. 2. To cycle through the various measurements press the UP and DOWN key as desired. The measurement unit currently selected will be indicated in the display. 3. Volts are displayed in Volts (true RMS), Current is displayed in Amps (true RMS), Watts are displayed in active power Watts, VA is displayed in apparent power VA (VA=Vrms*Arms), Frequency is displayed in Hertz (Hz), Power Factor (P.F.
Release the RESET key. This indicates that previous measurements have been deleted and that the total accumulated KWH, Elapsed Time and Cost measurements have been reset to zero. Retained measurements: 1. When power to the Kill A Watt™ EZ is interrupted, the display will go blank and the unit will stop measuring consumption and elapsed time. However all accumulated measurements including KWH, Elapsed Time, and actual total cost will be retained. 2.
P3 INTERNATIONAL CORPORATION LIMITED WARRANTY P3 INTERNATIONAL CORPORATION (“P3”) warrants to the original retail purchaser only, that its product is free from defects in material or workmanship under the condition of normal use and service for a period of six (6) months from the date of purchase.
