Owlet Cam 2 Installation Guide 1
EN Let’s Get Started Download the Owlet App. Plug in and follow app instructions to pair the Cam 2 with your Owlet Account. If you’ve already downloaded the Owlet App, click the Account tab to add a new device. Remember: the Cam 2 allows for video and audio via secure, encrypted Wi-Fi. Only connect the Cam 2 to a private network that requires a secure password.
Choose Your View Place the Cam 2 and all cables 36 inches (92 cm) away from the edge of the crib. Cables within 36 inches (92 cm) of the edge of the crib should be covered. You can set up the Cam 2 in two ways: 1 Place it on a flat surface using the magnetic base and adjust for desired tilt angle. 2 Mount it on a wall above the crib using the base as a wall mount for a bird’s-eye view of the crib or for an expanded view of your nursery.
What’s in the Box Magnetic base Owlet Cam 2 Cables with Owlet wraps* and room temperature and humidity sensor Wall Mounting Kit Power adapter Tools Needed to Mount the Cam 2 Measuring tape (not included) 21x cable guards Mounting plate 18x long guards 1x end piece 2x L-brackets Small Phillips screwdriver 1x screw 4 (not included)
1. Measure and mark 36 inches (92 cm) (six cable guards) 36 inches (92 cm) Measure 36 inches (92 cm) (92 cm) from the top of your baby’s mattress and make a mark on the wall — this is where the Cam 2 will be mounted. Center this mark above baby’s crib for the optimal viewing angle. Consider which outlet to use. The outlet should be at least 36 inches (92 cm) away from the crib to ensure no exposed cables will be within baby’s reach. The next steps will instruct you on how to cover all cables.
2. Align and fasten 3. Unwind the cable 4. Thread the cable sticker Align the center hole of the mounting plate with the mark you’ve made on the wall. Using the provided screw, fasten the mounting plate to the wall with the arrows pointing upward. 6 Remove the cable wraps and unwind the cable. Thread the cable down the channel of the mounting plate, aligning the orange sticker on the cable to the top of the mounting plate.
5. Mount the base 6. Attach the Cam 2 sticker Position the large holes of the magnetic base over the protruding tabs on the mounting plate, then slide downward until it clicks. Attach the Cam 2 to the magnetic base. Plug the cable into the Cam 2. The orange sticker should be placed just above the mounting plate so that you have enough cable slack to position the Cam 2 to your desired angle.
7. Mount cable guards The cable guards use high-strength adhesive. Take your time during installation to ensure proper placement.
8. Mount L-bracket L-brackets Use the right or left L-bracket to guide the cable in the direction of the wall outlet. Install long guards until any cable within 36 inches (92 cm) of the edge of the crib is covered. Continue adding long guards as needed to reach the outlet. Finally, install the end piece when you are within 6-10 inches of the outlet (this allows enough room to wrap excess cable with velcro).
9. Wrap excess cable with velcro Need Help? Gather the excess cable into a loop. Secure the top section of the loop by feeding the cable wrap through the first hole. The Owlet logo faces outward. Secure the bottom section of the loop to the top section by feeding the cable wrap through the second hole (The loop should now look like a bow). Secure remaining cable wrap.
WARNING: Strangulation Hazard! Children have STRANGLED in cords. Always use protective covering when used within 3 feet of crib. Check before each use to ensure the cord is not exposed to your child. Immediately discontinue use if the protective covering is damaged or broken. Do not remove tag from cord or protective covering. IMPORTANT SAFETY INSTRUCTIONS • WARNING: The Owlet Cam 2 is not a medical device. It is not intended for use as a medical device or to replace a medical device.
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
IC Warning This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.