User's Manual

ManualsBrandsOvisLink ManualsElectronicsMotion Sensor

Table of Content

Adding to Remove from Z-Wave

Network ........................................................................................................ 1

Z- Wave

Notification ...................................................................................................................................... 2

Z-Wave

Message Report ................................................................................................................................. 2

* Motion Report: ......................................................................................................................................... 3

* Tamper Report: ......................................................................................................................................... 3

* Timing Report: ......................................................................................................................................... 3

Power Up Procedure ............................................................................................................................................ 3

* Battery Power Check ................................................................................................................................. 3

* PIR Warm Up ........................................................................................................................................... 3

* NWI ........................................................................................................................................................ 4

* Wake ....................................................................................................................................................... 4

Security Network ................................................................................................................................................ 4

Operation Mode .................................................................................................................................................. 4

Choosing a Suitable Location ................................................................................................................................ 4

Z-Wave Configuration Settings ............................................................................................................................. 5

Z-Wave Supported Command Class ....................................................................................................................... 5

Specifications ..................................................................................................................................................... 8

FCC Interference Statement .................................................................................................................................. 9

Warning ............................................................................................................................................................. 9

Summary of content (10 pages)

PAGE 1
Table of Content Adding to Remove from Z-WaveTM Network ........................................................................................................ 1 Z- WaveTM Notification ...................................................................................................................................... 2 Z-WaveTM Message Report ................................................................................................................................. 2 * Motion Report: ................
PAGE 2
SI-102 SI-102-FCC Motion Sensor The motion sensor SI-102 has PIR function, based on Z-WaveTM technology. This device is a Security Enabled Z-Wave Plus Product. Z-WaveTM is a wireless communication protocol designed for home automation, specifically to remotely control applications in residential and light commercial environments.
PAGE 3
Function Description 1. Have Controller entered inclusion mode. 2. Pressing button once to enter the inclusion mode. Z-WaveTM Add 3. After add successful, the device will wake to receive the setting command from Z-WaveTM controller about 20 seconds. Remove 1. Have Z-WaveTM Controller entered exclusion mode. 2. Pressing button once to enter the exclusion mode. Node ID has been excluded. Reset Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable. 1.
PAGE 4
* Motion Report: When the PIR motion detected, the device will unsolicited to send the report to the nodes in the group 1. Notification Report (V4) Notification Type: Home Security (0x07) Event: Motion Detection, Unknown Location (0x08) Sensor Binary Report (V2) Sensor Type: Motion (0x0C) Sensor Value: 0xFF * Tamper Report: Both the 2 tamper keys are pressed over 5 seconds. The device will into the alarm state.
PAGE 5
* NWI When the device power on, the device will check is it already adding to the network? If doesn't, it will auto start the NWI mode. The LED will flash in every second and continue 30 seconds. Until timeout or the device successful to inclusion by controller. The use can presses button once to abort the NWI mode. * Wake When the device power on, the device will wake about 20 seconds. In this duration, the controller can communicate with the device.
PAGE 6
Z-Wave Configuration Settings Notice: * All of the configuration, the data size is 1. * The configuration mark with star(*), means after the remove the setting still keep, don't reset to factory default. Unless the user execute the “RESET” procedure. * The reserve bit or not supported bit is allowed any value, but no effect.
PAGE 7
0 Bit3: When Bit2 is 0 (Enable), Are the device and the lighting in the same room? 0: In the same room (Default), 1: In the different room. 0 Bit4: Disable delay 5 seconds to turn off the light, when door/window closed. (1:Disable, 0:Enable) 0 Bit5: Disable auto turn off the light, after door/window opened to turn on the light. (1:Disable, 0:Enable) Notice: If bit2 is zero, this setting is useless. Notice: If the No. Name 7 (*) Customer Function 0 Bit6: Reserve. 0 Bit7: Reserve. Def.
PAGE 8
9 Turn Off 4 0~127 Light Time After turn on the lighting, setting the delay time to turn off the lighting when the PIR motion is not detected. 8 seconds per tick, default tick is 4 (32 seconds). 0 means never send turn off light command. 10 20 Auto Report Battery Time 12 Auto Report 30 Tick Interval 0~127 The interval time for auto report the battery level. 0 means turn off auto report battery. The default value is 12. The tick time can setting by the configuration No.20.
PAGE 9
Specifications Power by CR123A lithium battery. Signal (Frequency): 868.40 MHz, 869.85 MHz(EU), 908.40 MHz, 916.00 MHz(US), 922~927 MHz(JP/TW), 921.40 MHz, 919.80 MHz(ANZ), 869.00 MHz(RU), 865.20 MHz(IN), 916.00 MHz(IL), Range: Minimum 40 meters indoor, 100 meters outdoor line of sight. RF Maximum Power: +5dBm Operating Temperature: -10oC ~ 40oC For indoor use only. Specifications subject to change without notice due to continuing product improvement. OvisLink Corp., http://www.airlive.
PAGE 10
FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.