User's Manual

ManualsBrandsOvisLink ManualsElectronicsDoor/window sensor + Illumination + Temperature 3 in 1 Multi-sensor

Table of Content

Add to/Remove from Z-Wave

Network ........................................................................................................... 1

Z-Wave

Notification ......................................................................................................................................... 2

Z-Wave

Message Report .................................................................................................................................. 3

* Door/Window Report: ................................................................................................................................. 3

* Tamper Report: ............................................................................................................................................ 3

* Temperature Report: .................................................................................................................................... 3

* Illumination Report: .................................................................................................................................... 4

* Timing Report:............................................................................................................................................. 4

Power Up Procedure ............................................................................................................................................... 4

* Battery Power Check ................................................................................................................................... 4

* NWI ............................................................................................................................................................. 5

* Wake ............................................................................................................................................................ 5

Over The Air (OTA) Firmware Update .................................................................................................................. 5

Security Network .................................................................................................................................................... 5

Function DIP Switch .............................................................................................................................................. 5

Operation Mode ...................................................................................................................................................... 6

Battery Installation ................................................................................................................................................. 7

Choosing a Suitable Location ................................................................................................................................. 7

Installation .............................................................................................................................................................. 8

Z-Wave Configuration Settings .............................................................................................................................. 8

Z-Wave Supported Command Class..................................................................................................................... 11

Specifications ....................................................................................................................................................... 12

FCC Interference Statement ................................................................................................................................. 13

Warning ................................................................................................................................................................ 13

Summary of content (14 pages)

PAGE 1
Table of Content Add to/Remove from Z-WaveTM Network ........................................................................................................... 1 Z-WaveTM Notification ......................................................................................................................................... 2 Z-WaveTM Message Report .................................................................................................................................. 3 * Door/Window Report: ........
PAGE 2
SI-101 3 in 1 Multi-sensor The slim multi-sensor has door/window, temperature and illumination, 3 sensors function in one, based on Z-WaveTM technology. It is the Z-WaveTM plus product, it support the security, OTA. Those newest features of the Z-WaveTM technology. Z-WaveTM is a wireless communication protocol designed for home automation, specifically to remotely control applications in residential and light commercial environments.
PAGE 3
Notice: Including a node ID allocated by Z-WaveTM Controller means “Add” or “Inclusion”. Excluding a node ID allocated by Z-WaveTM Controller means “Remove” or “Exclusion”. Function Add Remove Description 1. Have Z-WaveTM Controller entered inclusion mode. 2. Pressing tamper key three times within 1.5 seconds to enter the inclusion mode. 3. After add successful, the device will wake to receive the setting command from Z-WaveTM controller about 20 seconds. 1.
PAGE 4
Z-WaveTM Message Report When the door/windows triggered, the device will report the trigger event and also report the battery status, temperature and illumination level. In default the device will using Notification Report to represent the trigger event, it can be changed to Sensor Binary Report by setting the configuration NO. 7 Bit4 to 1. * Door/Window Report: When the door/window state changed, the device will unsolicited to send the report to the nodes in the group 1.
PAGE 5
The device will measure the temperature in every one minute. And if the temperature is over 140 degree Fahrenheit (60 degree Celsius), the device will always report in each measurement. * Illumination Report: When the door/window state changed, the device will unsolicited to send the “Sensor Multilevel Report” to the nodes in the group 1. Sensor Type: Luminance (0x03) Note: To disable this functionality by setting the configuration N0.5 bit4 to 1.
PAGE 6
* NWI When the device power on, the device will check is it already adding to the network? If doesn't, it will auto start the NWI mode. The LED will flash in every second and continue 30 seconds. Until timeout or the device successful to inclusion by controller. The use can press the tamper key 3 times to abort the NWI mode. * Wake When the device power on, the device will wake about 20 seconds. In this duration, the controller can communicate with the device.
PAGE 7
OFF OFF Customer Mode. According to the configuration setting NO. 5 to set the operation mode. Operation Mode There are two modes “Test” and “Normal”. “Test Mode” is for the user test the sensor function when installation. “Normal Mode” for the normal operation. When the event triggered, normally the LED won't indicated, unless the battery is in the low level, the LED will flash once. But in the “Test Mode” the LED also will light ON one second.
PAGE 8
Battery Installation When the device report the low battery message. The user should replace the battery to new one. The battery type is CR123A, 3.0V. The way to open the front cover please follow below steps. 1. Using a tool to press the 1-1 position, to release the cover. 2. Hold the front cover and pull back 3. Hold the front cover and pull up Replace the new battery and install the cover back. 1. Put the front cover bottom to 1-1, and press down. 2. Push the front cover top to 2-1.
PAGE 9
Installation 1. In the first time, add the device into the Z-WaveTM network. First, make sure the primary controller is in the inclusion mode. And then power on the device, just take out the insulation Mylar in the back side of the device. The device will auto start the NWI (Network Wide Inclusion) mode. And it should be included in 5 seconds. You will see the LED light ON one second. 2.
PAGE 10
Notice: * All of the configuration, the data size is 1. * The configuration mark with star(*), means after the remove the setting still keep, don't reset to factory default. Unless the user execute the “RESET” procedure. * The reserve bit or not supported bit is allowed any value, but no effect. NO. Name Def. Valid Description Setting the BASIC command value to turn on the light. The 2 Basic Set Level OxFF All 0xFF(-1) means turn on the light. For dimmer equipment 1 to 100 means the light strength.
PAGE 11
0 Bit7: Disable the back key release into test mode. (1:Disable, 0:Enable) NO. Name Def. 6(*) Mult- Sensor 4 Function 0 Switch Valid Description All Multisensor function switch. Using bit to control Bit0: Disable magnetic integrate illumination to turn ON the lighting nodes in the association group 2. (1:Disable, 0:Enable) 0 Bit4: Disable delay 5 seconds to turn off the light, when door/window closed. 0 Bit5: Disable auto turn off the light, after door/window opened to turn on the light.
PAGE 12
configuration No.20. NO. 13 Name Auto Report Def. Valid Description 12 0~ The interval time for auto report the temperature. 127 0 means turn off auto report temperature. Temperature Time The default value is 12. The tick time can setting by the configuration No.20. 20 Auto Report 30 0~ 0xFF Tick Interval The interval time for auto report each tick. Setting this configuration will effect configuration No.10, No.11, No.12 and No.13.
PAGE 13
Specifications Power by CR123A lithium battery. Signal (Frequency): SI-101: 868.40 MHz, 869.85 MHz(EU), SI-101: 908.40 MHz, 916.00 MHz(US), SI-101: 922~927 MHz(JP/TW), SI-101: 921.40 MHz, 919.80 MHz(ANZ), SI-101: 869.00 MHz(RU), SI-101: 865.20 MHz(IN), SI-101-IL:916.00 MHz(IL), Range: Minimum 40 meters indoor, 100 meters outdoor line of sight. RF Maximum Power: +5dBm Operating Temperature: -10oC ~ 40oC For indoor use only.
PAGE 14
FCC ID: ODMSI101 FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.