GW-300NAS Wireless 2T2R 300Mbps Giga NAS Router User’s Manual AirLive GW-300NAS User’s Manual
Copyright and Disclaimer Copyright & Disclaimer The contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an information retrieval system, translated into any language, or transmitted in any form or by any means, mechanical, magnetic, electronic, optical, photocopying, manual, or otherwise, without the prior written permission. Trademarks All products, company, brand names are trademarks or registered trademarks of their respective companies.
Copyright and Disclaimer CE Declaration of Conformity This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022/A1 Class B.
Table of contents Table of contents 1.INTRODUCTION ............................................................................................................... 1 1.1 Package List ............................................................................................................ 2 1.2 Hardware Installation ............................................................................................... 3 1.2.1 Hardware configuration .................................................................
1. Introduction 1 1.Introduction Congratulations on your purchase of this outstanding product: WiFi Broadband Router. This product is specifically designed for those who need to have the file sharing and P2P download services beyond his home and office. It provides a complete solution for Internet surfing and broadband sharing. Instructions for installing and configuring this product can be found in this manual.
1. Introduction 1.
1. Introduction 1.2 Hardware Installation 1.2.
1. Introduction 1.2.2 LED indicators Status LED USB LED WAN LED Ethernet LED WiFi LED Power LED LED Status Description Green Power ON Green Green in flash Green Green in flash Green Green in flash Green USB storage attached Data access Press ‘USB off’ button till LED flashing, then can remove USB storage when LED stop flashing. It is connected to local Ethernet.
1. Introduction How to Operate DO NOT connect WiFi Broadband Router to power before performing the installation steps below. Step 1. Screw the antenna in a clockwise direction to the back panel of the unit. Step 2. Plug the RJ45 cable into LAN port 1~4 and connect with your PC or NB. Step 3. Plug your RJ-45 into the WAN port and connect with your xDSL modem.
1. Introduction Step 4. Plug the power jack into it. Step 5. Power ON. Step 6. Prepare a USB Storage and then plug into the USB port.
2. Getting Started 2 2.Getting Started Please use windows EZ setup utility or Web UI wizard to enter the setup process. 2.1 Easy Setup by Windows Utility Step 1. Install the Easy Setup Utility from the provided CD then follow the steps to configure the device. Step 2. Select Language then click “Next” to continue.
2. Getting Started Step 3. Then click the “Wizard” to continue. Step 4. Click “Next” to continue.
2. Getting Started Step 5. One free DDNS account ‘ MAC address.ezguard.net’ for end user to access the NAS router remotely, you can rename an alias name to remember it easily. Once you type in a name, you can click ‘ check’ to see if the name server accept it or not. You also can click ‘Ignore’ to pass it. Step 6. Select Wireless Enable, and then click “Next” to continue.
2. Getting Started Step 7. Enter SSID, Channel and Security options, and then click “Next” to continue. Step 8. Select Auto Detect WAN service.
2. Getting Started Step 9. Save the setting. Step 10. Congratulations! Setup is completed. Now you have already connected to Internet successfully.
2. Getting Started 2.2 Easy Setup by Configuring Web UI You can also browse UI of the web to configure the device. Browse to Activate the Setup Wizard Type in the IP Address (http://192.168.1.254) Type the default Username and password ‘admin’ in the System Password and then click ‘login’ button. Select your language. Select “Wizard” for basic settings in simple way. Press “Next” to start the Setup Wizard.
2. Getting Started Configure with the Setup Wizard Step 1 You can change the password of administrator here. Step 2 Select Time Zone. Step 3 You can select Auto detecting WAN type or setup WAN type manually.
2. Getting Started Step 4 The system will detect the WAN type if you choose to let the system detect automatically. Step 5 Type in Host name and ISP registered MAC address. (if no such information, you can go next) Step 5-1 Wireless setting. Step 5-2 Wireless authentication and encryption.
2. Getting Started Step 6 Check the information again. Step 7 System is applying the setting. Step 8 Click finish to complete it.
3. Making Configuration . 3 3.Making Configuration Whenever you want to configure your network or this device, you can access the Configuration Menu by opening the web-browser and typing in the IP Address of the device. The default IP Address is: 192.168.1.254. Enter the default username and password “admin” in the System Password and then click ‘login’ button. Afterwards, select ‘Advanced’ indicated in the user interface for further configuring this device.
3. Making Configuration Note : Once you type in username and password ‘ guest/guest’, you can see as below WebHDD contents, which means your guest can only be allowed to check the ‘public’ area in the Hard drive under this NAS router. 3.
3. Making Configuration 3.1.1 Network Setup There are two ways to configure the network, respectively LAN Setup and Internet setup. LAN type LAN IP Address: The local IP address of this device. The computer on your network must use the LAN IP address of this device as their Default Gateway. You can change it if necessary. 2. Subnet Mask: Input your Subnet mask. (All devices in the network must have the same subnet mask.) The default subnet mask is 255.255.255.0. Internet Setup 1.
3. Making Configuration Activate WWAN for Auto-Failover: With this function enabled, when the Ethernet WAN connection is broken, the device will automatically activate the WWAN connection and keep you connected to internet with the alternative WWAN broadband service. Meanwhile, if the device detected that the Ethernet WAN connection is recovered, your broadband connection will be switched to use the Ethernet WAN service.
3. Making Configuration C. PPP over Ethernet Activate WWAN for Auto-Failover: With this function enabled, when the Ethernet WAN connection is broken, the device will automatically activate the WWAN connection and keep you connected to internet with the alternative WWAN broadband service. Meanwhile, if the device detected that the Ethernet WAN connection is recovered, your broadband connection will be switched to use the Ethernet WAN service.
3. Making Configuration Assigned IP Address: It is required by some ISPs. (Optional) Maximum Transmission Unit (MTU): Most ISP offers MTU value to users. The default MTU value is 0 (auto). NAT disable: The device would not send private IP to other LAN PC if you select disable. D.
3. Making Configuration Gateway IP and Server IP Address/Name: The IP address of the PPTP server and designated Gateway provided by your ISP. PPTP Account and Password: The account and password your ISP assigned to you. If you don't want to change the password, keep it blank. Connection ID: Optional. Input the connection ID if your ISP requires it. Maximum Idle Time: the time of no activity to disconnect your PPTP session. Set it to zero or enable “Auto-reconnect” to disable this feature.
3. Making Configuration Activate WWAN for Auto-Failover: With this function enabled, when the Ethernet WAN connection is broken, the device will automatically activate the WWAN connection and keep you connected to internet with the alternative WWAN broadband service.
3. Making Configuration DHCP Server: Choose either Disable or Enable. If you enable the DHCP Server function, the following settings will be effective. IP Pool Starting/Ending Address: Whenever there is a request, the DHCP server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting / ending address of the IP address pool. Lease Time: DHCP lease time to the DHCP client.
3. Making Configuration Press “Fixed Mapping” and the DHCP Server will reserve the special IP for designated MAC Address.
3. Making Configuration 3.1.3 Wireless Settings Wireless settings allow you to set the wireless configuration items. Wireless Module: You can enable or disable wireless function. Network ID (SSID): Network ID is used for identifying the Wireless LAN (WLAN). Client stations can roam freely over this device and other Access Points that have the same Network ID.
3. Making Configuration Open Open system authentication simply consists of two communications. The first is an authentication request by the client that contains the station ID (typically the MAC address). This is followed by an authentication response from the AP/router containing a success or failure message. An example of when a failure may occur is if the client's MAC address is explicitly excluded in the AP/router configuration.
3. Making Configuration Wireless Bridging: You could enable this function by selecting “Enable”. Remote AP MAC 1~Remote AP MAC 2: Enter the wireless MAC into the blank. Encryption type: Select the appropriate category. Once you set up that type of encryption, second LAN PC must enter the same encryption type as the first one. Encryption key: Set up encryption key based on the rule of encryption type. Once you set up encryption, second LAN PC must enter the same encryption type as the first one.
3. Making Configuration AP PIN: You can press Generate New Pin to get an AP PIN. Config Mode: Select your config Mode from “Registrar” or “Enrollee”. Config Status: It shows the status of your configuration. Config Method: You can select the Config Method here from “Pin Code” or “Push Button”. WPS status: According to your setting, the status will show “Start Process” or “No used”. Press “Wireless Clients List” and the list of wireless clients will be shown consequently. 3.1.
3. Making Configuration NAS Configuration Disk Utility 1. Format This utility would format the certain partition. Please be noted! This action will clear all your data in this partition. You will not be able to recover it any more. 2. Check This utility could help you check the partition, find the lost files, try to fix some problems. File Sharing Basic Setting These settings are for Samba Server (Windows Network Neighbors).
3. Making Configuration FTP Service These settings are for FTP service. FTP Port: The default port is 21, but sometimes you might want to hide your FTP service by changing it. We have the ability to receive the request on non-standard FTP port, but please be noted, some NAT router could not support non-standard FTP port, that means some of your clients might have to use passive mode to get file. Client Support UTF8: This option is used when your FTP client could support UTF8.
3. Making Configuration User Configuration In this page, you can manage the user account. Key in the user name and password then press “Add” could let you add a new user. If you want to delete an account, select it and click “Delete” button. iTunes Server This function could enable the built-in iTunes Server to support iTunes which is a media player released by Apple. Server Name: The name of this server, it will be shown on the iTunes.
3. Making Configuration Download Assistant FTP If you want to download something from a FTP site regularly but you don’t want to spend time on remembering doing this, this FTP download assistant could help you. Job Name: It’s for you to remember the job easily, and the device would use this name to info you when the job is done. URL: The URL for the file you want to download. You have to use this format: IP/path/file, you don’t have to add protocol part such like “ftp://”.
3. Making Configuration Start Time: Schedule: this device will start FTP download on the time that you specified. The schedule job that is saved could be check on Status page by selecting “View Scheduled Download Status”. At Once: the FTP download would be started immediately. HTTP Job Name: It’s for you to remember the job easily, and the device would use this name to info you when the job is done. URL: The URL for the file you want to download.
3. Making Configuration BT (Bit Torrent) Start BT download First, you have to get a seed file, which we called “torrent”. Then click the “Open” link on UI, it would pop up a sub menu to let you upload. Or, if your torrent file could be download from network, you could just enter a URL.
3. Making Configuration BT download status After you upload the torrent, download job would be started immediately.The device could support 3 concurrent download jobs, other jobs would wait in job queue. If one of the three running job is done, the next new job would be started.At this page, you could see the download process and the bandwidth. Stop, Resume and Remove seed Select any job on the list, and click right button of mouse, you could see a menu with several actions you could do.
