Montego Fire Pit Table Installation Instructions for Montego Fire Pit Models MG-1242-BLSM-K and MG-1242-BLK-K 1
IMPORTANT Please consult your Crystal Fire instruction manual for detailed instructions and important information related to hooking up your linear burner, including safety information, proper tightening of connections with two Tools…………………………….…..2 wrenches and full burner setup and lighting Required instructions. Contents Included with your Fire Pit……………….3 DO NOT ATTEMPT TO INSTALL CF-1242 BURNER WITHOUT FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL. Assembly Instructions………………….
Included with your Fire Pit Gas Valve Kit M6 Allen Wrench [X 1] Bolt Caps [X 4] Bolt A [X 4] Bolt B [X 4] M6X35 M6X20 TOUCH UP PAINT Touch-up Paint [X 1] Bolt C [X 4] Gas Valve (x1) Mounting screws (x2) Control knob (x1) M6X16 Top Clear Silicone Pads [X 6] Bottom Panel A [X 1] Center Support [X 1] Panel B [X 1] Panel C [X 1] Access Door [X 1] Glass Top Glass Cover 3
1. Assembly Instructions Unpack the fire pit table contents fromyour the box,Fire and remove Included with Pit individual packaging from each piece. A. 4 Fasteners 2. Lay Panel A on soft, flat surface. B. 4 B-Bolts 3. Position Center Support on Panel A. NOTE: it isC.very important 4 C-Bolts to place the Center Support exactly as shown in the picture below. This will ensure that your burner (and propane tank, if D. 4 Bolt Caps applicable) will fit correctly with your fire pit table base.
4. Stand up Panel A and use 2 more Bolt A to attach Center Support to Panel B. A 5. Use Bolt B (x4) to attach Panel C as shown. Panel C B A 6. Remove the 4 pre-installed bolts (Bolt C) from the underside of the Glass Top , set the top into place on the base, and reinstall the bolts to fasten the top to the base. Optional: Attach Bolt Caps to Bolt C if you desire. Simply press on. C 7. Once the Glass Top is in place, attach the Access Door to the fire pit table base.
CF-SPARKER Installation Locate CF-SPARKER inside of Crystal Fire® Plus burner box. Remove CF-SPARKER cap and hex nut. Insert AAA battery (not included) with + end out. Install CF-SPARKER into control panel as shown below. Depress CF-SPARKER button to test your sparker. Locate and orient sparker box on control panel as shown. Sparker box must be installed before burner valve.
Gas Connections Read and understand your Crystal Fire® Plus owner’s manual before beginning burner hookups or using the device. Do not use Teflon tape or pipe dope on flare fittings. See Crystal Fire® Plus instructions for burner installation. All gas connections were completed at the factory. Check all connections for leaks. If needed, tighten connection with 2 wrenches and re-check for leaks. Attach burner valve to control panel with provided screws as shown below.
Thermocouple Installation • Refer to Crystal Fire® Plus instruction manual for detailed attachment of thermocouple. Igniter Attach thermocouple to burner valve as shown below. • Igniter Electrode Installation Plug both BLACK wires hanging from the burner into the back of the CF-SPARKER. If an orange wire is present, do not use it. The orange wire is for Direct Spark Ignition system only. Test system by pushing the button on the igniter.
Glass Installation 1. Scatter all of the included Glass Beads evenly onto burner surface. DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER WITHOUT GLASS BEADS OR OTHER DECORATIVE MEDIA PRESENT 2. Place a single Silicone Pad in each corner and two in the center as shown below. 3. Set the cover into place on top of the burner with silicone pads facing down.
After installing igniter and making gas connections, verify that all connections are tight and that no leaks are present using a solution of soapy water or a commercially available leak-check solution. Position Your Tank (if applicable) 1. Remove door, connect the propane hose/regulator to the propane tank and hand tighten (DO NOT USE A WRENCH) and slide the propane tank past the dotted line to ensure the door closes properly. 2.
IMPORTANT Please consult your Crystal Fire® Plus instruction manual for detailed instructions and important information related to hooking up your linear burner, including safety information, proper tightening of connections with two wrenches and full burner setup and lighting instructions. DO NOT ATTEMPT TO INSTALL CFP1242 BURNER WITHOUT FIRST CONSULTING THE CRYSTAL FIRE® PLUS OWNER’S MANUAL.