Installation Instructions

how to install.
1. Charge overnight by plugging your OtO into an outlet using the included Power Adapter (found inside the
device). This ensures you are setting up with a full charge.
2. Download the OtO Lawn app from the Apple App Store® or Google Play® store.
3. Create an account.
4. Select Add New Device.
5. Place device in a spot that is well within range of 2.4 GHz Wi-Fi signal and receives a minimum of 3 hours
per day of direct sunlight (if using the on-board solar panel). Do not install until Wi-Fi strength has been
veried.
6. Turn the Switch. Select your OtO device from the list.
7. Connect to your home’s Wi-Fi network.
Note: The OtO unit only works with 2.4 GHz Wi-Fi. If device
does not connect, consider moving the router closer to the unit.
8. Device will connect and update rmware. This may take up
to 5 minutes. If device does not connect, refer to the
Troubleshooting section.
9. Name your device.
10. Choose to mount the device against a wall or in the ground.
Hose and water pressure
• With proper use, OtO typically reaches a maximum of 30 feet (9 m) with a minimum ow rate of 5.6 GPM.
• Generally speaking, the best kind of hose to use is a high-quality 5/8” garden hose.
• Use as short of a hose as possible to minimize pressure loss (max 50 feet).
• We recommend no more than two OtO units per water source.
• We do not recommend exi/expandable or light-duty garden hoses.
CAUTION
Pressurized hose may burst in high heat. Do not leave your hose pressurized and exposed to the sun.
In order to keep your drinking water safe from contamination, the faucet that OtO will be connected to needs
protection from the possibility of water owing backward. Commonly known as a backow device, government
regulations specify what type of backow device is required to adequately prevent water from owing
backward when a device such as OtO is connected to the water supply. Since the type of backow device and
maintenance schedule required by regulation varies at the city level, OtO is not responsible for damage or harm
caused by not installing and maintaining the appropriate backow device for your area. For more detail, visit
support.otolawn.com.
PATENT PENDING. FOR USE WITH COLD WATER ONLY. KEEP FROM FREEZING.
getting started.
For detailed installation instructions and videos, visit support.otolawn.com or use the QR code:
To help with your OtO setup and coverage planning, try our online tool: otolawn.com/#lawnTool
1. Push the mounting bracket into the ground
until the top is ush with surface. Use a blunt
piece of wood as a mallet, if necessary.
2. Attach the four thumb screws to the device.
3. Push the device ‘feet’ into the bracket holes
until all four are clicked into place.
1. Use the four included screws to secure the bracket into a wood fence.
Note: Use appropriate hardware (not included) if installing into
masonry.
2. Pass the threads on the 4 thumb screws through the mounting bracket
holes and secure them to the device.
Ground installation Fence/wall installation
3h
Pair Button
LED Status Light
LED Status Light
Wake Switch
Power Port
1
2
Wi-Fi signal strength
• Make sure to pick a place within range of your
network. Thick or insulated walls can greatly
reduce Wi-Fi signal strength even if your router
is close by. Test the Wi-Fi strength with the app
before you mount and connect your device.
• Device will only work on 2.4 GHz frequency.
Sunlight and power
• The on-board solar panel requires a minimum of
3 hours per day of direct, unobstructed sunlight.
• If your device’s location does not receive enough
sunlight, the provided cable and wall adapter can
be used either permanently or as a power boost
when needed.
3h
Note: Device must be mounted or it will tip over when running.
11. Attach hose.
12. Turn on water completely. Make sure there are no leaks at any connection point.