WISER2400.PLUS Wireless Serial Port Adapter Technical Manual Copyright Information in this document is subject to change without notice. Complying with all applicable copyright laws is the responsibility of the user. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of the seller. If, however, your only means of access is electronic, permission to print one copy is hereby granted.
TABLE OF CONTENT CHAPTER 1 INTRODUCTION... 1 SPECIFICATIONS eerie ranee ones mess chess can sans ar sso om a Rbe 40704 P EA EAE 440 £82007 ne rs ara nbn ARS RRR 3 CHAPTER 2 INSTALLATION OF WISER2400.PLUS INSTALLATION OF WISEACRE PLUS HARDWARE. Stendhal Hardware Items. Power... ne RS232 Connection, tests LESS. INSTALLATION OF WISER2400.PLUS UTILITY SOFTWARE System Requirements. CHAPTER 3 DIAGNOSTIC AND CONFIGURATION UTILITY OVERVIEW... PASSWORD F LINK STATUS PANEL CONFIGURATION PANEL A. Levied Port.
Chapter 1 INTRODUCTION Note: The terms Wiseacre and WiIiSER2400.PLUS are used interchangeably throughout this document WiSER2400.PLUS is an IEEE 802.11b compliant radio with an RS$232 serial interface. The WISER2400.PLUS radio takes serial data from the equipment or computing device connected via its R8232 port, converts the serial data into data packets®, and transmits these packets with the RF modulation that is compliant with the specifications of the 802.11b physical layer.
WISER2400.PLUS 802.11b Radio Key Features C1 Plug & Play operation— o No driver on (he host device is required for radio operation o Radio operation is independent of the operating system on the host equipment or device (Windows 98/NT/2000/MESXP, Linux, Unix, embedded, etc.), as Jon as an RS232 port is properly supported 2 Supports 64-bit and [28-bit WEP encryption for secured communication 2 industry standard IEEE 802.
Chapter 2 INSTALLATION OF WISER2400.PLUS Installation of WiSER2400.PLUS Hardware Standard Hardware elms 1 WISER2400.PLUS radio 1 R$232-P cable 1 RE232-C cable 1 ac-DE power adapter 1 pair of Velcro mounting pads Power This radio connected to your equipment draws power from the provided AG-DC power adapter that plugs into a wall outlet. R8232 Connection The WISEACRE, PLUS radio is shipped with two RS232 cables: 1. The RS-232-P cable is intended for connecting the WISERZ2400.
The WISER2400.PLUS radio is a client Station. As a station, one of the most useful diagnostic tools may be the green RX LED: a blinking green RX LED indicates the absence of a useful communication fink while running under infrastructure mode.
Chapter 3 Diagnostic and Configuration Utility Overview This chapter describes the functionalities and operations of WISER2400.PLUS Diagnostic and Configuration Utility program. The utility program can be used to configure and monitor WISER2400.PLUS radios. The WISER2400.PLUS utility program is supported on Microsoft Windows® 98(SE), NT, Millennium, 2000, and XP. The Utility program can monitor and SR [al | configure the WISER2400.
connection with a TCP/IP Tirelessness network. The PC which runs the Utility program must lase be part of the same Tirelessness network. The Utility program, when first started, will automatically scan for all available WiSER2400.PLUS units on the network. The user can also force a scan by clicking the "East MACKINAC” button. The scan result will be displayed in the pull-down menu at the top of the Utility program.
Dor HIRE Pam Coveted T0855 Lik thou 100% Fighters 2. Radio Link Status Panel Figure 3. Configuration Panel Configuration Panel This pane!, activated by clicking on the Configuration tab shown in Figure 3, includes three sub-sections under “TCP/UDP” section: Wireless settings, RS232 settings, and IP settings. “Point to Paint” section is not available for this version of WISER2400.PLUS. To retrieve the settings, click on the [Refresh | button at the bottom of the utility.
The WISER2400-1P supports only RS232 serial mode. Data Packaging Start Frame Byie(s): This value pacifies a special character that signals the start of a command (or data). Range from 0x00 fo 0x1F and options of “None” and “Other”. If “none” is selected, there would be no Start Frame Byte. If “Other” is selected, the user can click on “Other” and open a window where the users can configure Start Frame Byte up to & byes of their choice. Default value: none.
UPD: enables the WISER2400,PLUS to run UDP protocol. Receive Broadcast Packet: Optional operation mode which enable WISEACRE radio io receive UDP broadcast packet. Send Serial Data Broadcast: Optional operation mode which allows the data from the serial interface being transmitted as UDP broadcast. Note: each protocol is running exclusively. For example, while running UDF mode, the WISEACRE radio will not accept connections for either TCP Server or Client. C.
D. Peer Host Destination Unit MAC Address: The MAC address of the destination device. The radio unit learns the MAC address of the destination unit from ARP response packets sent from the device with associated IP address. iP Address: The configurable IP address of the device which this WISEACRE radio is sel to communicate with, For TCP server and UDP modes, the IP Address can be left as 0.0.0.0. However, for TCP client mode, thees must be a valid IP address filled here.
WEP Keys Creation Sub-panel This sub-pane! allows user to generate users’ own WEP encryption keys and can be made active only when either 84 bits or 128 bits radio button in the Encryption sub panel is selected. There are two methods to generate WEP encryption keys. One is lo use lhe auto key generation through the Passphrase field, and the other meted is to manually input a sel of keys in the Manual Entry fields.
EE ET Soften] Tix Saiph fe Dab Ire Sadie re | finis Erin Dusk ix Apoptosis ON Snr Sector LM Accord ADE bytes offense Err 1Bpbes Brock Detect hal Lama Far Bites a — PATTI Fe CT IA] Frames Novartis Byes Jo en inter Ee Terr Rey Fares.
Admin . Transmitted Re fried Frames: This number is the total SingleRetryFrames and Multimillionaires that the MAC transmitted. . Transmitted Octets: This number is the loyal bytes that the MAC successfully transmitted {(Communicates and Multiculturalism) . Received Frames: This number is the total Unicameral and Multiculturalism that the MAC successfully received. .
Chapter 4 — Trouble Shooting Blank Pages Appear When Open the Utility Program lt is possibly due to the unavailability of the COM port. Please pay attention to the Connection and Status field at the bottom of the program's main window. Press the you have another running program that accesses the same COM port.
Radio same time and therefore cause packet collision. To solve this problem, rearrange the Stations in question such that the RF signals are mutually sensible by all Stations. There is no guarantee that the packet collision can be entirely eliminated, but the severity can be reduced enough to see visible improvement of the link quality. Terence You may be able fo minimize RF interference by doing the following: .
Appendix A. WiSER2400.PLUS Cable Configuration This section describes the cables used for the Wiseacre-IP radio units to connect with RS232 equipment. The Figure A. below is the R8232-C serial cable used for connecting the computer serial/ R8232 connector to the WISEACRE PLUS radio unit. jpovacsuna a 0 Fig we A. RS232-C Serial Cable The Figure B. is the RS232-P serial cable commonly used for connecting a RS232 equipment fo a WISER2400-IP radio unit. EEA LIN Figure B.
Appendix B: Limited Warranty The seller warrants to the end user (“Customer} that this product will be free from defects in workmanship and materials, under normal use and service, for one {1) year from the date of purchase from the seller or ite authorized reseller.
Appendix C: Regulatory Compliance FCC Part 15 Declaration of Conformity {DoC} The equipment is confirmed to comply with the requirements of FCO Park 15 rules. The operation is subject lo he following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference halt may cause undesired operation.