Copyright © 1998 OTC Telecommute Inc., San Jose, CA. All rights reserved. This manual is copyrighted with all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language in any form by any means without the written permission of OTC Telecommute, incorporated. Trademarks AIFEZY2411 lan Bridge, the Airfare logo, OTC Telecommute Inc., and the OTC Telecommute logo are trademarks of OTC Telecommute, Inc.
on the outside of the box. GTC Telecommute cannot be held responsible for any product returned without an RMA number, and no product will be accepted without an RMA number.
DECLARATION OF CONFORMITY We OTC Telecommute Inc., 2036 Bering Drive San Jose, CA, 95131 Telephone: Declare under our sole responsibility that the product Airedale-BRG Complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CONTENTS 1.0 INTRODUCTION 2.0 SYSTEM REQUIREMENTS 3.0 PRODUCT PACKAGE 4.0 INSTALLATION OVERVIEW 4.1 Airedale LAN Bridge DIAGNOSTIC SOFTWARE 4.
1.0 Introduction Congratulations on your purchase of OTC Telecommute Airedale LAN Bridge! The ArEZY2411 ean Bridge is a cost effective “plug and play” wireless Ethernet Bridge that can provide wireless network connectivity when people and information are scattered among several nearby buildings within a few of miles {line of sight is required between the two connectivity points). OTC Telecommute wireless bridge provides wireless point to point connectivity and high performance.
1 diskette Diagnostic and Configuration Software Custom configurations: Please see Packing List enclosed with shipping boxes Overview After removing Airedale &'lan Bridge from the shipping box, be sure to lay cut all the contents to ensure that all necessary components are accounted for before you begin the installation process, Refer to Section 3.0 of this manual for a complete list of provided components.
We recommend that the user familiarize themselves with the wireless bridge hardware and review the HELP menu on the Diagnostic Configuration diskette before attempting any re-configurations. Configuration Guide: 1) Connect the ArEZY2411 elan Bridge units to a PC's Ethernet port via a straight-through UTP cable. 2) Run the diagnostic program 3) In the Diagnostic program's main menu, select item Control and Con fig 4) A configuration will pop up.
4) Run the RF cable along the antenna mast to where the Airedale elan Bridge unit will be located. 5) Secure the cable approximately away from the Airedale elan Bridge unit to allow for stress relief along the RF cable. (Connecting the RF cable to the unit without stress relief in place will damage the connector assembly on the AitEZY2411 elan Bridge units!) After you have completed the installation of the antenna systems, please refer to the user's manual for the network connection.
Airedale elan Bridge Parabolic Grid Antenna Horizontal Polarization {Shown} Network HUB of Router Installation Guide Parabolic Grid Antenna Horizontal Polarization (Shown; KRE Cable | @—Lightning Ancestor Lighting Ar-aster R145 10 Network Network HUB or Router IrEZY2411-TRX elan nit AIEZY2411-TRX-elannit “Please use Cross-Over Cable for connection to Router/Switch or Hub. « Please use Straight-Through Cable for direct connection to (computer/serveri/laptop} Ethernet port.
Helpful Hints / Trouble Shooting Guide: Verifying Antenna Connection to RF cables 1} Be sure to check that the directional antennas connected to the RF cables are connected properly See the second diagram in Appendix B. Verifying Antenna placement and orientation 1} Antenna must be securely mounted on an antenna mast. (Do not freely place the anterior on the roof without the antenna attached to a mastitis system. Do not dangle the antenna off the side of a building.
LED Function Display yellow LED {Network Link} slow blinking pattern (CPU functional) green LED (RX) always on (receiving mode) red LED (TX) alternating on and off flash {transmitting made) red LED (Power) always on (indicates power) a) check to see that all abase T cables are connected properly b) verify that your file server / Ethernet card / hub / router / and or Bridge is configured properly. c} verify that your network operating system is functional on your server.
Cabling and Connection of Zaire 1) The majority of problems in connectivity with remote client sites can be traced to improper or poor antenna installation and undesirable placement of antenna mast.