November, 2019 CNT15 CONTEMPO MOBILE CART Assembly Instructions - Important: Carefully unpack and identify each component before attempting to assemble. Refer to parts list. Please take care when assembling the unit and always set the parts on a clean, soft surface. If you require any assistance with assembly, parts or information on other products, please visit our website: www.officestar.net or call or write us.
1. Do not use this product unless all screws and bolts are securely tightened. 2. Check that all screws and bolts are tight every three months or as needed. 3. Dispose of packing material properly. Do not use plastic cover as head covering. It may cause suffocation. 4. Do not use this product as a stepladder. 5. Use this product for its intended purpose only. 6. FOR INDOOR RESIDENTIAL USE ONLY.
. Rename all English discriptions to French discriptions.
3. Rename all English discriptions to French discriptions.
HARDWARE LIST NO DRAWING DESCRIPTION SIZE QUANTITY 1 Screw M4.2 x 1/2” 24 PCS + 3 EXTRA 2 Screw M4.2 x 1” 4 PCS 3 Screw M4.2 x 1-3/16” 14 PCS + 2 EXTRA 4 Bolt Ø1/4” x 1-3/16” 8 PCS + 1 EXTRA 5 Cam Screw N/A 14 PCS + 2 EXTRA 6 Cam Nut N/A 14 PCS + 2 EXTRA 7 Wooden Dowel N/A 9 PCS + 1 EXTRA 8 Caster N/A 3 PCS 9 Locking Caster N/A 2 PCS 10 File Bar N/A 2 PCS 11 Allen Wrench N/A 1 PC Phillips Screwdriver also needed for assembly (not provided).
DRAWER INSTALLATION If you need to remove the drawer with ball bearing slides from the unit, follow the steps below to prevent any damage to the slides or the drawer. If you need to remove the drawer, please pull the drawer all the way out, then push the plastic release lever of the ball bearing slide up on one side and down on the other side, and then pull the drawer completely out. See detail #A.
STEP 1 (5) (C) (E) (F) FULLY TIGHTEN ALL CAM SCREWS (5) USING PHILLIPS SCREWDRIVER (NOT PROVIDED). STEP 2 (A) (4) (11) (D) DO NOT FULLY TIGHTEN BOLTS.
STEP 3 (B) (1) (D) DO NOT FULLY TIGHTEN SCREWS. STEP 4 (D) (4) (C) (11) FULLY TIGHTEN ALL BOLTS.
STEP 5 (H) (H) (E) (6) (7) FULLY TIGHTEN CAM NUTS (6) USING PHILLIPS SCREWDRIVER (NOT PROVIDED). STEP 6 (E) (7) (6) FULLY TIGHTEN CAM NUTS (6) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).
STEP 7 (C) (F) (6) (E) (7) FULLY TIGHTEN CAM NUTS (6) USING PHILLIPS SCREWDRIVER (NOT PROVIDED). STEP 8 (9) (1) (8) FULLY TIGHTEN ALL SCREWS (1) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).
STEP 9 (J) (N) (M) (L) (3) DO NOT FULLY TIGHTEN SCREWS. STEP 10 (K) (J) (3) (L) (O) (M) FULLY TIGHTEN ALL SCREWS (3) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).
STEP 11 (2) (J) (I) FULLY TIGHTEN ALL SCREWS (2) USING PHILLIPS SCREWDRIVER (NOT PROVIDED). STEP 12 (3) (P) (N) FULLY TIGHTEN ALL SCREWS (3) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).
STEP 13 (1) (8) FULLY TIGHTEN ALL SCREWS (1) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).
STEP 15 (10)