Application Guide

ManualsBrandsORIVISION ManualsAccessories & SuppliesH.265 1080P@30fps SDI Video Encoder Encoder HD-SDI Transmitter with HTTP,RTSP,UDP,SRT,HLS,RTMP,Multicast,SD HD 3G to IP Encoder IPTV HD Video Audio Unitcast hdmi to rtsp multiviewer Encoder

Table Of Contents

ORIVISION Support team

Technical support: support@zydz-china.com

How to log in the control web of video encoder

1. Reset

1.1 how to reset the video encoder

If can’t log-in the encoder by the default IP or your set IP, pls Insert a needle into the ''RST'' hole and

press the reset button, the indicator light of ''STA'' will twinkle fast. When the indicator light of ''STA'' is

off, reset successfully. All parameters will be initialized.

1.2 After reset,

The default IP address is 192.168.0.31

The default log in ID and password is ''admin''

2. Log In Control Web

2.1 Why do you can’t log in the control web

Most of customers can't log in the control panel of video encoder by directly enter 192.168.0.31 in

browser. The reason is that the IP address of video encoder (192.168.0.31) and IP address of PC (laptop)

are not in the same network segment, so you can’t communicate each other. In order to log in the

control web of video encoder, you need to change the IP address of PC (laptop) first.

2.2 How to change the IP

Step 1: Connect the video encoder to router or switch by Ethernet cable

Step 2: Connect a PC (laptop) to the same router or switch. Open the window of <Network and Sharing

Center>

Step 3: Click ''Local Area Connection''

Step 4: Click ''Details'', You can see the IP address and default gateway of your PC (laptop) here. As

shown the picture bellow. IP (PC/Laptop) is 192.168.1.100, Gateway is 192.168.1.1, DNS service is

192.168.1.1

Summary of content (6 pages)

PAGE 1
How to log in the control web of video encoder 1. Reset 1.1 how to reset the video encoder If can’t log-in the encoder by the default IP or your set IP, pls Insert a needle into the ''RST'' hole and press the reset button, the indicator light of ''STA'' will twinkle fast. When the indicator light of ''STA'' is off, reset successfully. All parameters will be initialized. 1.2 After reset, The default IP address is 192.168.0.31 The default log in ID and password is ''admin'' 2. Log In Control Web 2.
PAGE 2
DNS Step 5: Click ''Properties''— ''Internet Protocol Version 4(TCP /IPv4)'', as shown the picture bellow. Step 6: Choose ''Use the following IP address'', Then change the IP address of PC (laptop), and click ''OK''. You can set the IP address to 192.168.0.** (** is a number from 2 to 255 except for 31) and set the default gateway to 192.168.0.1. Technical support: support@zydz-china.
PAGE 3
Step 7: Log in the control panel of video encoder 192.168.0.31 the default ID and password is ''admin''. Now you can log in the control web of video encoder. 192.168.0.31 admin admin Step 8: After login the control web of the video encoder, you need to change the IP address of the video encoder to make it be in the wide-area network, then you can use your PC(laptop) to log in then video encoder in the wide-area network. Technical support: support@zydz-china.
PAGE 4
Step 9: Change the IP in the Network Setting page. Please refer to the IP address of your PC(laptop) before changing IP of video encoder. Check step 4, you have already knew the IP and gateway of PC(Laptop). In that case, that IP of router (PC/laptop) is 192.168.1.100, gateway is 192.168.1.1,DNS is 192.168.1.1 So, you can set the IP as 192.168.1.168 (192.168.1.xx; xx is a number from 2 to 255 except for 100) Gateway is 192.168.1.1. DNS is 192.168.1.
PAGE 5
Step 12: Now you can login the control web by a new IP (192.168.1.168) 192.168.1.168 admin admin Congrat ulation! You can use the PC(laptop) in wide area network and log in the control panel of video encoder simultaneously. Please remember IP address of video encoder. 3. Q&A Q: Why I can’t login the 192.168.0.31? Technical support: support@zydz-china.
PAGE 6
A: The reason is that the IP address of video encoder (192.168.0.31) and IP address of router/PC /laptop are not in the same network segment, so you can’t communicate each other. In order to log in the control web of video encoder, you need to change the IP address of PC (laptop) first. Q: After changed the IP, I still can’t login the control web of the encoder by new IP A: First, after all sets, you need “reboot” the encoder. Confirmed you have done.