Su b w o of e r OWNER'S MANUAL MODEL CO104S CO124S CO154S
TABLE OF CONTENTS English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Español. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WHAT’S IN THE BOX Included in this box are all the necessary mounting hardware and cables for your basic installation. Listed below is a detailed list of the components included in this system package. Quantity Description 1 Installation and Operation Manual 1 Orion™ Cobalt woofer 1 Mounting template Mounting screws INSTALLATION The performance of these Cobalt subwoofers is directly proportional to the quality of the installation.
FEATURES 15 1 2 13 3 14 4 12 5 6 7 11 10 9 8 1 Polypropylene dust cap - moisture and UV resistant. 2 Oversized NBR (Nitrile-butadiene Rubber) surround for linear controlled long excursion. 3 Vented paper cone - moisture and UV resistant. 4 Custom stamped steel frame. 5 Vented Kapton voice coil former (10” & 12" uses 1.5" voice coil former, 15” use a 2" voice coil former). 6 8mm steel front plate. 7 Large 2 stack ceramic magnets. 8 8mm steel back plate/pole piece T yoke assembly.
WIRING CONFIGURATIONS The following illustrations provide guidelines on properly connecting your Orion Cobalt woofer to an Orion Cobalt amplifier for maximum performance.
One Speaker (4 ohm voice coil) One 4 ohm voice coil woofer results in a 4 ohm load to the amplifier. _ 4 ohm + Figure 3 Figura 3 Abbildung 3 + _ 1. Connect the speaker by connecting the positive (+) terminal of the woofer to the positive (+) terminal on the amplifier. Wire the negative (-) terminal of the woofer to the negative (-) terminal on the amplifier.
Series—Two Speakers (Single 4 ohm voice coils) Two single 4 ohm voice coil subwoofers with the voice coils connected in series to result in an 8 ohm load to the amplifier. _ _ 4 ohm 4 ohm + + Figure 4 Figura 4 Abbildung 4 + _ 1. Connect the woofers in series by connecting the negative (-) terminal of the first woofer voice coil to the positive (+) terminal of the second woofer voice coil. 2. Wire the positive (+) terminal of the first woofer voice coil to the positive (+) terminal on the amplifier.
Series/Parallel - 4 Speakers (Single 4 Ohm Coils) 4 single 4 ohm voice coil subwoofers with the voice coils of each pair of speaker wired in series and then all 4 speakers wired in parallel to result in a 4 ohm load on the amplifier. _ 4 ohm 1 _ _ 4 ohm 2 _ 4 ohm 3 + 4 ohm 4 + + + Figure 5 Figura 5 Abbildung 5 + _ 1. Connect the negative (-) terminal from speaker 1 to the negative terminal on speaker 3 and then hook that wire to the negative (-) terminal on the amplifier. 2.
ENCLOSURE RECOMMENDATIONS Enclosure Details 1. External dimensions calculated for 3/4” building material 2. Includes speaker displacement 3. Volumes given are net tuning volume 4. Enclosures include a minimal amount of damping material. Just enough material to line the inside of the enclosure is required. Cobalt CO104S Sealed Enclosure Recommendations A C B Top & Bottom c b a d c Front & Back Sides Figure 6 Figura 6 Abbildung 6 8 External Dimensions A = 14 in B = 12.5 in C = 11.
Cobalt CO104S Vented Enclosure Recommendations Figure 7 Figura 7 Abbildung 7 A C B Top & Bottom c b a d c Front & Back Sides —Box Parts— Box Shape: Square Prism 1 Top, 1 Bottom: depth (c) = 12 in width (b) = 14.25, thickness = 0.75 in 1 Front, 1 Back: height (a) = 14.25 in width (d) = 12.75, thickness = 0.75 in 2 Sides: height (a) = 14.25 in depth (c) = 12, thickness = 0.75 in —Driver Mounting— Front VENT Round h e External Dimensions A = 15.75 in B = 14.
Cobalt CO124S Sealed Enclosure Recommendations A C B Top & Bottom c b a d c Front & Back Sides Figure 8 Figura 8 Abbildung 8 10 External Dimensions A = 15.5 in B = 14.75 in C = 12 in Internal Dimensions A = 14 in B = 13.25 in C = 10.5 in Wall Thickness Front = 0.75 in Side = 0.75 in —Box Parts— Box Shape: Square Prism 1 Top, 1 Bottom: depth (c) = 12 in width (b) = 14.75, thickness = 0.75 in 1 Front, 1 Back: height (a) = 14 in width (d) = 13.25, thickness = 0.
Cobalt CO124S Vented Enclosure Recommendations Figure 9 Figura 9 Abbildung 9 A C B Top & Bottom c b a d c Front & Back Sides —Box Parts— Box Shape: Square Prism 1 Top, 1 Bottom: depth (c) = 13 in width (b) = 16.75, thickness = 0.75 in 1 Front, 1 Back: height (a) = 16.5 in width (d) = 15.25, thickness = 0.75 in 2 Sides: height (a) = 16.5 in depth (c) = 13, thickness = 0.75 in Driver Mounting Mounting: Front VENT Round h e External Dimensions A = 18 in B = 16.
Cobalt CO154S Sealed Enclosure Recommendations A C B Top & Bottom c b a d c Front & Back Sides Figure 10 Figura 10 Abbildung 10 12 External Dimensions A = 25 in B = 17.5 in C = 11.5 in Internal Dimensions A = 23.5 in B = 16 in C = 10 in Wall Thickness Front = 0.75 in Side = 0.75 in —Box Parts— Box Shape: Square Prism 1 Top, 1 Bottom: depth (c) = 11.5 in width (b) = 17.5, thickness = 0.75 in 1 Front, 1 Back: height (a) = 23.5 in width (d) = 16, thickness = 0.75 in 2 Sides: height (a) = 23.
Cobalt CO154S Vented Enclosure Recommendations Figure 11 Figura 11 Abbildung 11 A C B Top & Bottom c b a d c Front & Back Sides g - OR VENT Square e h h g © 2008 directed electronics—all rights reserved —Box Parts— Box Shape: Square Prism 1 Top, 1 Bottom: depth (c) = 13 in width (b) = 17.5, thickness = 0.75 in 1 Front, 1 Back: height (a) = 23.5 in width (d) = 16, thickness = 0.75 in 2 Sides: height (a) = 23.5 in depth (c) = 13, thickness = 0.
SPECIFICATIONS Model/Part Number CO104S CO124S CO154S Fs (free-air resonance, Hz) 39.2 25.6 25.2 Vas (equivalent compliance, cu. ft.) 1.080 4.017 7.098 Vas (equivalent compliance, liters) 30.600 113.790 201.070 Qms (Q, mechanical) 3.53 4.72 6.08 Qes (Q, electrical) 0.68 0.55 0.51 Qts (total driver Q) 0.57 0.49 0.47 Re (DC resistance, ohms) 3.6 3.55 3.77 Z (nominal impedance, ohms) 4 4 4 Le (inductance, mh) 1.38 1.37 1.61 Efficiency (1W @ 1M, dB) 86.1 87.2 89.
A B C D E Figure 12 Figura 12 Abbildung 12 CO104S CO124S CO154S Dimensions inches/mm, Dimensions po/mm, Dimensiones plg./mm, Abmessungen Zoll/mm, Dimensioni pollici/millimetri, Dimensões polegadas/mm A 5.12/130 5.51/140 6.46/164 B 1.97/50 1.97/50 2.01/51 C 4.96/126 5.00/127 5.71/145 D 9.13/232 10.91/277 13.82/351 E 10.16/258 12.20/310 15.
FRANÇAIS CARACTÉRISTIQUES 15 1 2 13 3 14 4 12 5 6 7 11 10 9 8 1 Cache-poussière en polypropylène — résiste à l'humidité et aux ultraviolets 2 Panneau surdimensionné en nitrile pour un mouvement long à contrôle linéaire 3 Membrane de papier ventilée — résiste à l'humidité et aux ultra-violets 4 Cadre sur mesure en acier matricé 5 Gabarit ventilé Kapton de bobine acoustique (les modèles 10” et 12" utilisent le gabarit 1,5", le modèle 15” utilisent le gabarit 2") 6 Platine avant en acier
CONFIGURATIONS DE CÂBLAGE Les illustrations suivantes fournissent des indications sur le câblage correct de votre haut-parleur Orion Cobalt à un amplificateur Orion Cobalt pour un rendement optimal.
Série/parallèle — 4 haut-parleurs (bobines 4 ohms simples) Quatre caissons de basses à bobines acoustiques simples de 4 ohms, les bobines acoustiques de chaque paire de haut-parleurs raccordées en série et les quatre haut-parleurs raccordés en parallèle, résultent en une charge de 4 ohms pour l'amplificateur. 1. Raccordez la borne négative (-) du haut-parleur #1 à la borne négative du hautparleur #3, puis raccordez ce câble à la borne négative (-) de l'amplificateur. 2.
Recommandations pour l'enceinte close Cobalt CO104S (Figure 6) Recommandations pour l'enceinte ventilée Cobalt CO104S (Figure 7) Dimensions externes A = 14" B = 12,5" C = 11,5" Dimensions internes A = 12,5" B = 11" C = 10" Épaisseur de la cloison Avant = 0,75" Côté = 0,75" Dimensions externes A = 15,75" B = 14,25" C = 12" Dimensions internes A = 14,25" B = 12,75" C = 10,5" Épaisseur de la cloison Avant = 0,75" Côté = 0,75" — Parties du boîtier — Forme: prisme carré 1 haut, 1 bas Profondeur (c) = 11,5" L
Recommandations pour l'enceinte close Cobalt CO124S (Figure 8) Recommandations pour l'enceinte ventilée Cobalt CO124S (Figure 9) Dimensions externes A = 15,5" B = 14,75" C = 12" Dimensions internes A = 14" B = 13,25" C = 10,5" Épaisseur de la cloison Avant = 0,75" Côté = 0,75" Dimensions externes A = 18" B = 16,75" C = 13" Dimensions internes A = 16,5" B = 15,25" C = 11,5" Épaisseur de la cloison Avant = 0,75" Côté = 0,75" — Parties du boîtier — Forme: prisme carré 1 haut, 1 bas: Profondeur (c) = 12" La
Recommandations pour l'enceinte close Cobalt CO154S (Figure 10) Recommandations pour l'enceinte ventilée Cobalt CO154S (Figure 11) Dimensions externes A = 25" B = 17,5" C = 11,5" Dimensions internes A = 23,5" B = 16" C = 10" Épaisseur de la cloison Avant = 0,75" Côté = 0,75" Dimensions externes A = 25" B = 17,5" C = 13" Dimensions internes A = 23,5" B = 16" C = 11,5" Épaisseur de la cloison Avant = 0,75" Côté = 0,75" — Parties du boîtier — Forme: prisme carré 1 haut, 1 bas: Profondeur (c) = 11,5" Largeu
SPÉCIFICATIONS Modèle/Numéro de pièce Directed CO104S CO124S CO154S Fs (résonance air libre, Hz) 39.2 25.6 25.2 Vas (volume d'air équivalent, pi cu) 1.080 4.017 7.098 Vas (volume d'air équivalent, litres) 30.600 113.790 201.070 Qms (facteur de qualité mécanique) 3.53 4.72 6.08 Qes (facteur de qualité électrique) 0.68 0.55 0.51 Qts (facteur de qualité total) 0.57 0.49 0.47 Re (résistance CC, ohms) 3.6 3.55 3.77 Z (impédance nominale, ohms) 4 4 4 Le (inductance, mh) 1.
ESPAÑOL CARACTERÍSTICAS 15 1 2 13 3 14 4 12 5 6 7 11 10 9 8 1 Tapa de polipropileno contra el polvo; resistente a la humedad y a los rayos ultravioleta. 2 Envolvente grande de Goma de Butadieno de Nitrilo (Nitrile Butadiene Rubber, NBR) para grandes desplazamientos lineales controlados. 3 Cono de papel ventilado; resistente a la humedad y a los rayos ultravioleta. 4 Armazón de acero troquelado a la medida. 5 Formador de bobina de voz Kapton ventilado (1.5 plg.
CONFIGURACIONES DE CABLEADO Las siguientes ilustraciones contienen las pautas para conectar correctamente el woofer Orion Cobalt a un amplificador Orion Cobalt a fin de lograr el rendimiento máximo.. Potencia de amplificador recomendada Potencia continua (RMS) Potencia máxima (W) 1 woofer 100 a 300 200 a 600 2 woofers 200 a 600 400 a 1200 3 woofers 300 a 900 600 a 1800 4 woofers 400 a 1200 800 a 2400 En paralelo.
En serie / en paralelo. 4 altavoces (una bobina de voz de 4 Ω cada uno) Cuatro subwoofers, con una bobina de voz de 4 Ω cada uno, las bobinas de voz de cada par en serie y los 4 altavoces en paralelo producen una carga de 4 Ω en el amplificador. 1. Conecte la terminal negativa (-) del altavoz 1 a la terminal negativa (-) del altavoz 3 y luego conecte esa terminal a la terminal negativa (-) del amplificador. 2. Conecte la terminal positiva (+) del altavoz 1 a la terminal negativa (-) del altavoz 2 3.
Recomendaciones para la caja sellada Cobalt CO104S (figura 6) Recomendaciones para la caja ventilada Cobalt CO104S (figura 7) Dimensiones externas A = 14 plg. B = 12.5 plg. C = 11.5 plg. Dimensiones externas A = 15.75 plg. B = 14.25 plg. C = 12 plg. Dimensiones internas A = 12.5 plg. B = 11 plg. C = 10 plg. Dimensiones internas A = 14.25 plg. B = 12.75 plg. C = 10.5 plg. Grosor de la pared Delantera = 0.75 plg. Lateral = 0.75 plg. Grosor de la pared Delantera = 0.75 plg. Lateral = 0.75 plg.
Recomendaciones para la caja sellada Cobalt CO124S (figura 8) Recomendaciones para la caja ventilada Cobalt CO124S (figura 9) Dimensiones externas A = 15.5 plg. B = 14.75 plg. C = 12 plg. Dimensiones externas A = 18 plg. B = 16.75 plg. C = 13 plg. Dimensiones internas A = 14 plg. B = 13.25 plg. C = 10.5 plg. Dimensiones internas A = 16.5 plg. B = 15.25 plg. C = 11.5 plg. Grosor de la pared Delantera = 0.75 plg. Lateral = 0.75 plg. Grosor de la pared Delantera = 0.75 plg. Lateral = 0.75 plg.
Recomendaciones para la caja sellada Cobalt CO154S (figura 10) Recomendaciones para la caja sellada Cobalt CO154S (figura 11) Dimensiones externas A = 25 plg. B = 17.5 plg. C = 11.5 plg. Dimensiones externas A = 25 plg. B = 17.5 plg. C = 13 plg. Dimensiones internas A = 23.5 plg. B = 16 plg. C = 10 plg. Dimensiones internas A = 23.5 plg. B = 16 plg. C = 11.5 plg. Grosor de la pared Delantera = 0.75 plg. Lateral = 0.75 plg. Grosor de la pared Delantera = 0.75 plg. Lateral = 0.75 plg.
ESPECIFICACIONES Modelo/Número de pieza dirigido CO104S CO124S CO154S 39.2 Parámetros Thiele/Small Fs (resonancia al aire libre, Hz) 25.6 25.2 Vas (cumplimiento de equivalencia, pies3) 1.080 4.017 7.098 Vas (cumplimiento de equivalencia, litros) 30.600 113.790 201.070 Qms (Q, mecánico) 3.53 4.72 6.08 Qes (Q, eléctrico) 0.68 0.55 0.51 Qts (Q total del excitador) 0.57 0.49 0.47 Re (resistencia CC, Ω) 3.6 3.55 3.77 Z (impedancia nominal, Ω) 4 4 4 Le (inductancia, mH) 1.38 1.
DEUTSCH HÖHEPUNKTE 15 1 2 13 3 14 4 12 5 6 7 11 10 8 9 1 Feuchtigkeits- und UV-beständige Polypropylen-Abdeckung 2 Extra große Sicke aus NBR (Nitrilgummi) für linear kontrollierten Langhub 3 Belüftete feuchtigkeits- und UV-beständige Papiermembran 4 Spezieller Stahlblechrahmen 5 Belüfteter Kapton-Schwingspulenträger (10- und 12-Zoll-Modell verwendet 1,5-Zoll-Schwingspulenträger, 15-Zoll-Modell einen 2-ZollSchwingspulenträger) 6 8-mm dickes vorderes Abdeckblech 7 Große Double-Stack-K
SCHALTKONFIGURATIONEN Die folgenden Abbildungen zeigen, wie Sie Ihren Orion Cobalt-Tieftöner richtig an einen Orion Cobalt-Verstärker anschließen, um die maximale Leistung herauszuholen.
Reihe/Parallel - 4 Lautsprecher (Einzelne 4-Ohm-Schwingspulen) 4 einzelne Subwoofer mit 4-Ohm-Schwingspulen, bei denen die Schwingspulen jedes Lautsprecherpaars in Reihe geschaltet und dann alle 4 Lautsprecher parallel geschaltet sind: Lastwiderstand von 4 Ohm am Verstärker 1. Schließen Sie das negative (-) Terminal an Lautsprecher 1 an das negative Terminal an Lautsprecher 3 an und verbinden Sie diesen Draht mit dem negativen (-) Terminal am Verstärker. 2.
Cobalt CO104S Geschlossenes Gehäuse: Empfehlungen (abbildung 6) Cobalt CO104S Bassreflex-Gehäuse: Empfehlungen (abbildung 7) Außenmaße A = 14 Zoll (35,6 cm) B = 12,5 Zoll (31,8 cm) C = 11,5 Zoll (29,2 cm) Außenmaße A = 15,75 Zoll (40 cm) B = 14,25 Zoll (36,2 cm) C = 12 Zoll (30,5 cm) Innenmaße A = 12,5 Zoll (31,8 cm) B = 11 Zoll (27,9 cm) C = 10 Zoll (25,4 cm) Innenmaße A = 14,25 Zoll (36,2 cm) B = 12,75 Zoll (32,4 cm) C = 10,5 Zoll (26,7 cm) Wandstärke Vorn = 0,75 Zoll (1,9 cm) Seite = 0,75 Zoll (1,9
Cobalt CO124S Geschlossenes Gehäuse: Empfehlungen (abbildung 8) Cobalt CO124S Bassreflex-Gehäuse: Empfehlungen (abbildung 9) Außenmaße A = 15,5 Zoll (39,4 cm) B = 14,75 Zoll (37,5 cm) C = 12 Zoll (30,5 cm) Außenmaße A = 18 Zoll (45,7 cm) B = 16,75 Zoll (42,5 cm) C = 13 Zoll (33 cm) Innenmaße A = 14 Zoll (35,6 cm) B = 13,25 Zoll (33,7 cm) C = 10,5 Zoll (26,7 cm) Innenmaße A = 16,5 Zoll (41,9 cm) B = 15,25 Zoll (38,7 cm) C = 11,5 Zoll (29,2 cm) Wandstärke Vorn = 0,75 Zoll (1,9 cm) Seite = 0,75 Zoll (1,9
Cobalt CO154S Geschlossenes Gehäuse: Empfehlungen (abbildung 10) Cobalt CO154S Bassreflex-Gehäuse: Empfehlungen (abbildung 11) Außenmaße A = 25 Zoll (63,5 cm) B = 17,5 Zoll (44,5 cm) C = 11,5 Zoll (29,2 cm) Außenmaße A = 25 Zoll (63,5 cm) B = 17,5 Zoll (44,5 cm) C = 13 Zoll (33 cm) Innenmaße A = 23,5 Zoll (59,7 cm) B = 16 Zoll (40,6 cm) C = 10 Zoll (25,4 cm) Innenmaße A = 23,5 Zoll (59,7 cm) B = 16 Zoll (40,6 cm) C = 11,5 Zoll (29,2 cm) Wandstärke Vorn = 0,75 Zoll (1,9 cm) Seite = 0,75 Zoll (1,9 cm)
DATEN Modell/Directed-Teilenummer CO104S CO124S CO154S Fs (Freiluftresonanz, Hz) 39.2 25.6 25.2 Vas (Äquivalente Nachgiebigkeit, Kubikfuß) 1.080 4.017 7.098 Vas (Äquivalente Nachgiebigkeit, Liter) 30.600 113.790 201.070 Thiele/Small-Parameter Qms (Q, mechanisch) 3.53 4.72 6.08 Qes (Q, elektrisch) 0.68 0.55 0.51 Qts (totaler Treiberwert für Q) 0.57 0.49 0.47 Re (GS-Widerstand, Ohm) 3.6 3.55 3.77 Z (Nennimpedanz, Ohm) 4 4 4 Le (Induktivität, mh) 1.38 1.37 1.
ITALIANO CARATTERISTICHE 15 1 2 13 3 14 4 12 5 6 7 11 10 9 8 1 Protezione parapolvere in polipropilene - resistente all'umidità e ai raggi ultravioletti. 2 Surround maggiorato in NBR (gomma nitrile butadiene) per lunga escursione lineare controllata. 3 Cono aperto in carta - resistente all'umidità e ai raggi ultravioletti. 4 Telaio in acciaio stampato su misura.
CONFIGURAZIONI DI CABLAGGIO Le illustrazioni seguenti presentano delle indicazioni di massima su come collegare correttamente un woofer Orion Cobalt a un amplificatore Orion Cobalt in modo da ottenere le massime prestazioni.
4 diffusori collegati in serie-parallelo (con bobine mobili da 4 ohm) 4 subwoofer con una con bobina mobile da 4 ohm ciascuno, e con le bobine mobili di ogni coppia di diffusori collegate in serie e tutti i 4 diffusori collegati tra loro in parallelo, causano un carico di 4 ohm sull'amplificatore. 1. Collegare il terminale negativo (-) del diffusore 1 al terminale negativo (-) del diffusore 3 e quindi collegare il filo al terminale negativo (-) dell'amplificatore. 2.
Raccomandazioni per la cassa sigillata Cobalt CO104S (figura 6) Raccomandazioni per la cassa aperta Cobalt CO104S (figura 7) Dimensioni esterne A = 35,5 cm (14 in) B = 31,7 cm (12,5 in) C = 29,2 cm (11,5 in) DDimensioni esterne A = 31,7 cm (15,75 in) B = 28 cm (14,25 in) C = 25,4 cm (12 in) Dimensioni interne A = 31,7 cm (12,5 in) B = 28 cm (11 in) C = 25,4 cm (10 in) Dimensioni interne A = 31,7 cm (14,25 in) B = 28 cm (12,75 in) C = 25,4 cm (10,5 in) Spessore delle pareti Anteriore = 1,9 cm (0,75 in)
Raccomandazioni per la cassa sigillata Cobalt CO124S (figura 8) Dimensioni esterne A = 31,7 cm (15,5 in) B = 28 cm (14,75 in) C = 25,4 cm (12 in) Dimensioni interne A = 31,7 cm (14 in) B = 28 cm (13,25 in) C = 25,4 cm (10,5 in) Spessore delle pareti Anteriore = 1,9 cm (0,75 in) Laterale = 1,9 cm (0,75 in) — Parti della cassa — Forma della cassa: prisma quadrato 1 superiore, 1 inferiore: profondità (c) = 29,2 cm (12 in) larghezza (b) = 31,7 cm (14,75 in) = 14,75 spessore = 1,9 cm (0,75 in) 1 anteriore, 1 pos
Raccomandazioni per la cassa sigillata Cobalt CO154S (figura 10) Dimensioni esterne A = 31,7 cm (25 in) B = 28 cm (17,5 in) C = 25,4 cm (11,5 in) Dimensioni interne A = 31,7 cm (23,5 in) B = 28 cm (16 in) C = 25,4 cm (10 in) Spessore delle pareti Anteriore = 1,9 cm (0,75 in) Laterale = 1,9 cm (0,75 in) —Parti della cassa— Forma della cassa: prisma quadrato 1 superiore, 1 inferiore: profondità (c) = 29,2 cm (11,5 in) larghezza (b) = 31,7 cm (17,5 in) = 17,5 spessore = 1,9 cm (0,75 in) 1 anteriore, 1 posterio
DATI TECNICI Modello/Codici parti CO104S CO124S CO154S 39.2 Parametri Thiele/Small Fs (freq. di risonanza in aria libera, Hz) 25.6 25.2 Vas (volume equivalente di cedevolezza, cu ft) 1.080 4.017 7.098 Vas (volume equivalente di cedevolezza, litri) 30.600 113.790 201.070 Qms (Q, meccanico) 3.53 4.72 6.08 Qes (Q, elettrico) 0.68 0.55 0.51 Qts (Q totale driver) 0.57 0.49 0.47 Re (resistenza in c.c., ohm) 3.6 3.55 3.77 Z (impedenza nominale, ohm) 4 4 4 Le (induttanza, mH) 1.
PORTUGUÊS CARACTERÍSTICAS 15 1 2 13 3 14 4 12 5 6 7 11 10 9 8 1 Cobertura contra pó de polipropileno resistente à umidade e radiação ultravioleta. 2 Surround de borracha nitrílica (NBR) grande para longo deslocamento linear controlado. 3 Cone de papel ventilado resistente à umidade e à radiação ultravioleta. 4 Carcaça de aço estampado especial. 5 Bobina de copo Kapton ventilado (10” e 12” usam bobina de 1,5”; 15” usa uma bobina de 2”). 6 Placa frontal de aço de 8 mm.
CONFIGURAÇÕES DE CONEXÃO As próximas ilustrações fornecem diretrizes sobre como conectar o woofer Orion Cobalt a um amplificador Orion Cobalt para obter o máximo desempenho.
Em série/paralela - 4 alto-falantes (bobinas de 4 ohm simples) Quatro subwoofers com bobinas de 4 ohm simples, com as bobinas de cada par de alto-falantes conectadas em série e todos os quatro alto-falantes conectados em paralelo para resultar em uma carga de 4 ohm ao amplificador. 1. Conecte o terminal negativo (-) do alto-falante 1 ao terminal negativo (-) do alto-falante 3 e, em seguida, conecte este cabo ao terminal negativo (-) do amplificador. 2.
Recomendações para caixa selada para Cobalt CO104S (figura 6) Recomendações para caixa ventilada para Cobalt CO104S (figura 7) Dimensões externas A = 35,6 cm (14 pol.) B = 31,8 cm (12,5 pol.) C = 29,2 cm (11,5 pol.) Dimensões externas A = 40,0 cm (15,75 pol.) B = 36,2 cm (14,25 pol.) C = 30,5 cm (12 pol.) Dimensões internas A = 31,8 cm (12,5 pol.) B = 27,9 cm (11 pol.) C = 25,4 cm (10 pol.) Dimensões internas A = 36,2 cm (14,25 pol.) B = 32,4 cm (12,75 pol.) C = 26,7 cm (10,5 pol.
Recomendações para caixa selada para Cobalt CO124S (figura 8) Recomendações para caixa ventilada para Cobalt CO124S (figura 9) Dimensões externas A = 39,4 cm (15,5 pol.) B = 37,5 cm (14,75 pol.) C = 30,5 cm (12 pol.) Dimensões externas A = 45,7 cm (18 pol.) B = 42,6 cm (16,75 pol.) C = 33,0 cm (13 pol.) Dimensões internas A = 35,6 cm (14 pol.) B = 33,7 cm (13,25 pol.) C = 26,7 cm (10,5 pol.) Dimensões internas A = 41,9 cm (16,5 pol.) B = 38,7 cm (15,25 pol.) C = 29,2 cm (11,5 pol.
Recomendações para caixa selada para Cobalt CO154S (figura 10) Recomendações para caixa ventilada para Cobalt CO154S (figura 11) Dimensões externas A = 63,5 cm (25 pol.) B = 44,5 cm (17,5 pol.) C = 29,2 cm (11,5 pol.) Dimensões externas A = 63,5 cm (25 pol.) B = 44,5 cm (17,5 pol.) C = 33,0 cm (13 pol.) Dimensões internas A = 59,7 cm (23,5 pol.) B = 40,6 cm (16 pol.) C = 25,4 cm (10 pol.) Dimensões internas A = 59,7 cm (23,5 pol.) B = 40,6 cm (16 pol.) C = 29,2 cm (11,5 pol.
ESPECIFICAÇÕES Modelo/Número do produto CO104S CO124S CO154S Fs (ressonância ao ar livre, Hz) 39.2 25.6 25.2 Vas (conformidade equivalente, pés cúbicos) 1.080 4.017 7.098 Vas (conformidade equivalente, litros) 30.600 113.790 201.070 Qms (Q, mecânica) 3.53 4.72 6.08 Qes (Q, elétrica) 0.68 0.55 0.51 Qts (Q total do alto-falante) 0.57 0.49 0.47 Re (resistência à CC, ohms) 3.6 3.55 3.77 Z (impedância nominal, ohms) 4 4 4 Le (indutância, mh) 1.38 1.37 1.
™ WARRANTY LIMITED ONE-YEAR CONSUMER WARRANTY/*LIMITED TWO-YEAR CONSUMER WARRANTY FOR AUTHORIZED DIRECTED DEALER PURCHASE & INSTALLATION Directed Electronics (herein “Directed”) promises to the original purchaser of the subwoofer or amplifier, as applicable (herein “Unit” or “Product”), to repair or replace with a new or refurbished Unit (at Directed’s sole and absolute discretion) should the Unit prove to be defective in workmanship or material under normal use, for a period of *two-years from the date o
