9” DIGITAL COLOR MONITOR USER’S MANUAL MODEL No.
CONTENTS SAFETY INSTRUCTION 2 CAUTIONS 4 FCC RF INTERFERENCE STATEMENT 5 INSTALLATION 6 RESOLUTION 7 CONTROLS AND FUNCTIONS 8 REAR VIEW 13 POWER MANAGEMENT 14 SPECIFICATIONS 15 TROUBLE SHOOTING GUIDE 16 This Monitor was Manufactured by ISO 9001 Certified Factory 1 INSTRUCTION MANUAL
SAFETY INSTRUCTION 1. Read all of these instructions. 2. Save these instructions for later use. 3. Follow all warnings and instructions marked on the product. 4. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning. 5. Do not use this product near water. 6. Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to the product. 7.
SAFETY INSTRUCTION 13. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to service personnel. 14. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions. A. When the power cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D.
CAUTIONS NEVER REMOVE THE BACK COVER Removal of the back cover should be carried out only by qualified personnel. This display monitor contains high voltage inside. DO NOT USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard. Do not expose the unit to rain or moisture. This unit is designed to be used in the office or home. Do not subject the unit to vibrations, dust of corrosive gases.
FCC RF INTERFERENCE STATEMENT NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
INSTALLATION NO TOOLS ARE REQUIRED TO INSTALL THE MONITOR. SIMPLY FOLLOW THE INSTRUCTIONS OUTLINED IN THE NEXT FEW PAGES. 1. CONNECT THE SIGNAL CABLE A. ATTACHED SIGNAL CABLE 1) If the signal cable is attached on the monitor, connect the other and into the graphic card on back of the computer. 2) Secure the connection with the screws on the plug. B.
RESOLUTION This monitor is a digitally-controlled multi-frequency monitor. It operates at horizontal frequencies of 30 to 96KHz and vertical frequencies of 50 to 160Hz. Because of its micro processor-based designs it offers auto-synchronization and auto-sizing capabilities. This monitor offers 12 programmed settings as listed in the table below. These 12 preset modes cover most of the common video modes supported by popular graphic adaptors.
CONTROLS AND FUNCTIONS B.MENU BUTTON POWER INDICATOR(LED) A. POWER SWITCH C.SELECT BUTTON D. ADJUST BUTTONS (DOWN & UP) A. POWER ON/OFF( ) Turns the power ON or OFF. There will be a few seconds delay before the display appears. The power LED(next to the power switch) lights when the power is turned ON. The power is turned off by pressing the power switch again and the power LED goes out. B. MENU Activates and exits the On Screen Display. This button can also be used to move previous menu or status.
CONTROLS AND FUNCTIONS USER MENU 1 activates when you press the Menu button. USER MENU 2 activates via the adjust ( / ) button. C. SELECT The select button allows user to activate the desired adjustment with blinking icon. D. ADJUST ( ) The Adjust button allows user to choose the icons (controls) in the menu. Pressing the adjust button or will step through all available adjustment icons (controls).
CONTROLS AND FUNCTIONS 2. AUTO REGISTRATION This monitor has 12 preset modes. If the current video is one of the preset modes, the monitor keeps storing the custom display settings into the permanent memory. There are also 10 user modes that allow you to save the custom display settings made to any video mode that is not one of the preset modes. Adjustments are automatically registered without pressing any buttons. Up to 10 user modes are stored automatically on a “First-In-First-Out” basis. 3.
CONTROLS AND FUNCTIONS PIN BALANCE Adjusts the curvature of the left and right sides of the screen image. TILT Adjusts the tilt of image. RECALL Resets the control functions back to the original factory preset values. In order for the Recall function working, the timing must fall under one of the factory preset timing modes. COLOR TEMPERATURE Adjusts color temperature to 9300K, 6500K(notes : 9300K is factory default).
CONTROLS AND FUNCTIONS MOIRE Adjusts the moire level of the screen. Activate MOIRE icon & keep pressing select button approximately 2 seconds after select “ON”. H. MOIRE ADJUST Reduces the optical effect of horizontal wavy lines on the display image. These effects are usually more noticeable on large gray areas or on black & white check board patterns. V. MOIRE ADJUST Reduces the optical effect of vertical wavy lines on the display image.
REAR VIEW E. AC INLET Power cord connection. NOTES Power cord is used as main power disconnect device in this product. F. D-SUB CONNECTOR OF SIGNAL CABLE Connect to the analog RGB signal output connector of video card. E. AC INLET F. D-SUB CONNECTOR OF SIGNAL CABLE ACCESSORY 1. POWER CORD 2. INSTRUCTION MANUAL 3.
POWER MANAGEMENT This monitor features a power management system to “power down” upon receipt of the VESA DPMS(The display power management signaling) from a VESA DPMS video card. The VESA DPMS-compliant video card performs this signaling system through not sending horizontal, vertical, or sync signal. This monitor enters an appropriate mode through identifying each of the three modes of the signaling system.
SPECIFICATIONS CDT 19 (18 Viewable) diagonal measurement ARAS(Anti-Reflection Anti-Static) Coating. 0.26mm Dot Pitch RESOLUTION(H x V) 1600x1200 Non Interlaced FREQUENCY HORIZONTAL : 30-96KHz VERTICAL : 50-160Hz INPUT SIGNAL VIDEO(Analog 0.7Vp-p/75 ) SYNC(Separate and Composite TTL Level) ACTIVE DISPLAY AREA (W x H) Preset : 346mm X 255mm Full : 366mm X 275mm DIMENSIONS (W x D x H) 570mm X 565mm X 570mm (Carton Box) WEIGHT Net Weight : 21.0Kg Gross Weight : 24.
TROUBLE SHOOTING GUIDE TROUBLE No image on display screen TROUBLE SHOOTING TIP 1. Check that power cord of the Monitor have been connected securely into wall outlet or grounded extension cable or strip. 2. Powerf switch should be in the ON position and LED is lit. 3. Check that the Brightness and/or the Contract adjustments of the Display have not been turned down to minimum levels. “No signal, Check signal Cable” message on screen 1.
