CONTENTS SAFETY INSTRUCTION 2 CAUTIONS 4 FCC RF INTERFERENCE STATEMENT 5 INSTALLATION 6 RESOLUTION 7 CONTROLS AND FUNCTIONS 8 REAR VIEW 13 SPECIFICATIONS 14 TROUBLE SHOOTING GUIDE 15 WICHTIGE HINWEISE (GERMAN) 16 This Monitor was Manufactured by ISO 9001 Certified Factory 1 INSTRUCTION MANUAL
SAFETY INSTRUCTION 1. Read all of these instructions. 2. Save these instructions for later use. 3. Follow all warnings and instructions marked on the product. 4. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning. 5. Do not use this product near water. 6. Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to the product. 7.
SAFETY INSTRUCTION 13. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to service personnel. 14. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions. A. When the power cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D.
CAUTIONS NEVER REMOVE THE BACK COVER Removal of the back cover should be carried out only by qualified personnel. This display monitor contains high voltage inside. DO NOT USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard. Do not expose the unit to rain or moisture. This unit is designed to be used in the office or home. Do not subject the unit to vibrations, dust of corrosive gases.
FCC RF INTERFERENCE STATEMENT NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
INSTALLATION NO TOOLS ARE REQUIRED TO INSTALL THE MONITOR. SIMPLY FOLLOW THE INSTRUCTIONS OUTLINED IN THE FOLLOWING PAGE. 1. INSTALLING THE TILT/SWIVEL STAND 1) Align the stand with the front slots in the bottom of the monitor and insert the Tilt/Swivel Stand into the slots. 2) Push the Tilt/Swivel Stand firmly toward the front of the monitor until the latches click into the locked position. 1 2 2 Hook 2. CONNECT THE SIGNAL CABLE 1) Connect the end into the graphic card on back of the computer.
CONTROLS AND FUNCTIONS B. MENU BUTTON A. POWER SWITCH C. SELECT BUTTON D. ADJUST BUTTONS (DOWN & UP) A. POWER ON/OFF( POWER INDICATOR(LED) ) Turns the power ON or OFF. There will be a few seconds delay before the display appears. The power LED(next to the power switch) lights when the power is turned ON. The power is turned off by pressing the power switch again and the power LED goes out. B. MENU Activates and exits the On Screen Display.
CONTROLS AND FUNCTIONS MAIN MENU 1 activates when you press the Menu button. MAIN MENU 2 activates when you press ( ) at the CONTRAST(EXIT) icon in the menu1. C. SELECT The select button allows user to activate the desired adjustment with blinking icon. D. ADJUST ( , ) The Adjust button allows user to choose the icons (controls) in the menu. Pressing the adjust button or will step through all available adjustment icons (controls).
CONTROLS AND FUNCTIONS 2. AUTO REGISTRATION This monitor has 10 preset modes. If the current video is one of the preset modes, the monitor keeps storing the custom display settings into the permanent memory. There are also 10 user modes that allow you to save the custom display settings made to any video mode that is not one of the preset modes. Adjustments are automatically registered without pressing any buttons. Up to 10 user modes are stored automatically on a “First-In-First-Out” basis. 3.
CONTROLS AND FUNCTIONS CORNER CORRECTION User can select Top or Bottom Corner correction by pressing the Select button. TOP CORNER CORRECTION Corrects the top corner image shape to a rectangle. BOTTOM CORNER CORRECTION Corrects the bottom corner image shape to a rectangle. COLOR-TEMP Adjusts color temperature to 9300K, 6500K(notes : 9300K is factory default). Or, for a custom color mode, select “USER” and keep pressing select key approximately 2 seconds to activate the RGB Sub-menu.
CONTROLS AND FUNCTIONS OSD H.POSITION Moves the OSD position to left or right. OSD V.POSITION Moves the OSD position to up or down. OSD ON TIME If there isn’t key pressure OSD will be disappeared automatically the setted seconds later. VIDEO LEVEL Selects the video level of the Video Graphic Card. If the intensity of image is high select 1.0V & if low select 0.7V. MOIRE Adjusts the moire level of the screen. H. MOIRE ADJUST Reduces the optical effect of horizontal wavy lines on the display image.
REAR VIEW E. AC INLET Power cord connection. NOTE: Power cord is used as main power disconnect device in this product. F. D-SUB CONNECTOR OF SIGNAL CABLE Connect to the analog RGB signal output connector of IBM PS/2, or compatible computer. E. AC INLET F. D-SUB CONNECTOR OF SIGNAL CABLE ACCESSORY 1. POWER CORD 2.
SPECIFICATIONS PICTURE TUBE 17 (16V) Flat CDT Dot Type 0.25mm Pitch Black Matrix Screen High resolution screen Dark Faceplate Glass High contrast screen 90 Deflection and 29.1mm Diameter Neck Lower power consumption 16 Visual Screen Diagonal Full-square type screen Anti-Static Charge Face Electro static charge eliminated Hi-view(Silica coat, Anti-Glare, Anti-Reflection) Surface Glare problem eliminated Invar Shadow Mask. INPUT SIGNAL D-SUB INPUT Analog RGB Video: 0.7Vpp / 75 Sync.
TROUBLE SHOOTING GUIDE PROBLEM No Picture (Not in power saving mode) CHECK THESE ITEMS The video card should be completely seated in its slot. Power switch and computer power switch should be in the ON position. The signal cable should be completely connected to the video card/computer. Check connector for bent or pushed-in pins. LED on the monitor is not lit Power switch should be in the ON position and the power cord should be connected.