Make-me Book
Welcome to the Jungle This is where your origami comes to life. Follow the easy steps to create a springy jumping cat, snappy swimming crocodile, or even a cheeky talking frog, and discover new ways to have fun with your new Orimagi friends.
C o n te n ts s t n e t n Co Hello Worm Jumping Cat
Flapping Butterfly Talking Frog Swimming Crocodile
What’s in the Box Co n te le S e t nts o ld rt o en g 0 Orig am n b o R x5 x2 OriB Ju Foldable Jungle Map My Orimagi Toolbox Make-me Book Origami Paper Crease Patterns OriBendy Smart Motor USB Cable Clips More projects and instructions on OriApp i Pa dy pe ld fo n ,U r x15 Cl ip x2 Med4 ium C Bea ti re a m x18 it v x3 Lo 0 ng V Jo int Bea m x2 Y 0 Jo x3 int Sh 0 or tB ea m x18 T Jo Ju n g le S e t int re m ild so hing he et n bu u ca
t B o o k le e y rn Jo u d o lo r si t n a ib h g me e e t u li , is t , m s .
Hello Worm Hello Worm This little worm is easy to build. And once you’re done, you’ll know all the basic skills for making all your other creatures.
How to Fold a Beam Beams are really important. They’re what connects to the OriBendy smart motor and helps your Orimagi move.
1 1 2 3 4 1 Pop out one piece from Sheet A. 2 Put the plastic side face up. Fold along the dotted line and then unfold.
Hello Worm 3 Fold upwards along the creases to make a triangular beam. 4 Fold the sticky face down to stick your beam in place. Make sure all the creases are straight.
1 2 You made your fi 3 4 5 That’s it! You just made your first You made your first beam! beam. Great job! 5 Beams come in three sizes. Small (Yellow from Sheet A), Medium (Green, Sheet B) and Long (Blue, Sheet C). See if you can make all three sizes.
How to Fold a V Joint Joints help connect beams together to make your Orimagi strong.
1 2 3 1 Pop piece sheet D. Pop offout oneone piece from from sheet D 4 5 Pop out the middle piece.
3 Put the plastic side face up. Fold and unfold along each of the dotted lines. Peel the back off the tape. 4 Fold upwards along the creases to make a triangular beam.
1 2 3 5 4 Fold the sticky face down to stick your beam in place. Make sure all the creases are straight. Repeat steps 3 to 5 for the other end of the beam.
How to Fold a Y Joint
1 1 2 3 1 Pop out one piece from sheet E. 4 5 3 2 2 Put the plastic side face up. Fold and unfold along each of the dotted lines. Peel the back off the tape. Hello Worm Place the plastic side up.
3 Fold upwards along the creases to make a triangular beam. Hello Worm 6 4 Fold the sticky face down to stick your beam in place. Make sure all the creases are straight.
1 2 3 5 Repeat steps 2 to 4 for the other sides of your Y joint.
How to Fold a T Joint
1 1 2 3 1 Pop out one piece from sheet F. 4 5 3 2 Put the plastic side face up. Fold and unfold along each of the dotted lines. Peel the back off the tape.
4 Hello Worm al 3 Fold upwards along the creases to make a triangular beam. 4 Fold the sticky face down to stick your beam in place. Make sure all the creases are straight.
1 6 2 3 5 4 Repeat steps 2 to 4 for the other sides of your T joint.
+
Worm Head 1 2 Draw a Draw face for yourfor wildflower. a face your wildflower. Fold paper diagonally. 3 1 4 Fold paper diagonally to make a triangle. 2 Draw a face for your Hello Worm. Draw a face for your wildflower.
Easy! OriBendy Setup 1. Easy! Example 1 Example 2 squeeze here! here! 1 Slide a short beam into the slots on one side of OriBendy (Eg. 1) or directly push the beam into place (Eg. 2). 2. Hello Worm Example 1 Example 2 squeeze here! here! 3. 2 Slide a medium beam into the other slots on the same side of OriBendy here! (Eg. 1 or 2).
here! here! 1 squeeze here! here! 2 3 4 5 3 Gently insert a V Joint into the end of a long beam. Example 1 Example 2 4 Hello Worm Slide that beam into the slots on the end of OriBendy (Eg. 1) or directly push it into place (Eg. 2). Slide the assembly into the motor (Example 1).
5. squeeze Example 1 Example 2 5 Slide or push a clip onto the other end of the long beam (Eg. 1 or Eg. 2). 6 Attach your worm’s head to the clip. Hello Worm 6.
1 2 7.
Connect OriBendy to the App +
1 1. 2 3 Press the button to turn LEDto flashing). Press theon(Green button turn 4 1 LED will flash. on. Green Press the button to turn on(Green LED flashing). 5 2. 2 Hold button for 2 second to turn off. Green LED will turn off. Hello Worm Hold button for 1 seconds to turn off(Green LED off).
3. 3 Use the USB cable to charge. Red LED shows OriBendy is charging. When LED goes out, OriBendy is fully charged. Hello Worm 4. 4 Don’t try to force OriBendy while it is moving.
1 2 3 4 5. 5 5 Download OriApp from App Store® or Google PlayTM to play.
Warning Do NOT allow children under 3 years old to play with this product. This product contains small parts. Do NOT modify or disassemble OriBendy. Doing so may expose small parts or damage the product. Do NOT get any liquid on or into the product. Do NOT use product in extreme environment such as extreme hot or cold, dust, sand, or high humidity. Do NOT swallow any parts of the product. ONLY use standard USB ports(5V 1A) to charge OriBendy.
Legal Model: OIBY FCC ID: 2AS7COIBY Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Contact Us Orimagi, Inc. 100 William T. Morrissey Blvd., Venture Development Center, Boston, MA 02125-3393 www.orimagi.io For troubleshooting, warranty information, and return policy, please visit our website. © 2019 Orimagi, Inc. All rights reserved. Orimagi is a trademark of Orimagi, Inc. Android and Google Play is a trademark of Google LLC. App Store is a service mark of Apple Inc.
Fold Robot, Unfold Creativity For more fun projects and inspiration, check out the OriApp!