HDMI Extender over single 50m/164ft UTP Cables with IR Control User manual VER:1.
Thank you for purchasing this product. For optimum p e r f o r m a n c e a n d s a f e t y, p l e a s e r e a d t h e s e instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. 1. Introduction The HDMI Extender over Single Cat5e/6 with IR extends high de inition video and audio signals and IR, at a distance of up to 164ft/50m over a single Cat5e/6 cable.
The extender includes two units: transmitting unit and receiving unit. The transmitting unit is used to capture the HDMI input with IR signals and carries the signals via one cost effective Cat5e/6 cable. The receiving unit is responsible for equalizing the transmitted HDMI signal and reconstructing IR control signals. The extender offers the most convenient solution for HDMI extension over a single Cat5e/6 with long distance capability, and is the perfect solution for any application. 2.
Support copy EDID from receiver display or loop out display. Allows for cascading via additional HDMI loop out port. Support Power over cable function. Transmission Range: Extends 1080p resolution up to 164ft/50m over a single Cat5e or Cat6 cable. Works with HDMI and HDCP compliant devices. Supports up to 1080p High De inition resolution. Compact design for an easy and lexible installation. 4. Spec ications Video Bandwidth Video Support Audio Support: Single-link 165Mhz [ 4.
RJ-45 connector 3.5mm connector WE/SS 8P8C (TX and RX) IR Receiver/IR Blaster MECHANICAL SPECS Housing Power Supply Power consumption Operation temperature Storage temperature Relative humidity Metal enclosure (1) 5V1A DC 1.5 watts (TX); 1.0 watts (RX) 32~104 °F -4 ~140 °F 20~90 % RH (no condensation) 5. Panel descriptions 5.1 Transmitting unit 1 2 3 4 5 6 7 8 1.
2. EDID: The switcher can switch copy EDID function,switch to right position,the extender will copy hdmi loop out display EDID information to source. Switch to left position,the extender will copy Receiver display EDID to source. 3. HDMI out: This slot is to connect the HDMI input of your display such as an HDTV. 4. IR out: Connect the IR Blaster cable included in the package for IR signal transmission. Pace the IR blaster in direct line-of-sight of the equipment to be controlled. 5.
5.2 Receiver unit 1 2 3 4 5 6 7 1. EQ switcher: HDMI Receiver equalizer switcher. 2. HDMI out: This slot is to connect the HDMI input port of your display such as an HDTV. 3. IR in: Connect to the IR Receiver for IR signal reception. Ensure that remote being used is within the direct line-of-sight of the IR receiver. 4. Power LED: This LED will illuminate when the device is connected with power supply. 5.
5.3 RX Equalizer distance adjust If you see lickering or blinking image on the display, adjust the EQ switch to improve the cable skew. MAX stands for the strongest HDMI signal level for the longest possible transmission length while MIN stands for the weakest HDMI signal level for short transmission length. Adjust the signal level from MIN to MAX until desired video quality is displayed. Recommended EQ setting Position Cable Length under 15m (49.5ft) 15-30m (49.
6.
7. CONNECT AND OPERATE 1. Connect a source such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc. to the HDMI input on the Transmitting unit. 2. Connect a display such as an HDTV or HD Projector to the HDMI output on the Receiving unit. 3. Connect a single Category 5e/6 up to 164ft/50m to the output of the Transmitting unit, and the other end to the input of the Receiving unit. 4. For power, plug both the Transmitting unit and Receiving unit with the included power supplies.
vertical refresh rate may work better than 60 Hz or higher. Use the source remote at the receiver emitter to test IR functionality. If the IR remote function is not responding, check the emitters to ensure they are placed correctly and are plugged into the correct IR jacks on the Extender set receiving and transmitting units. 8.
IR RECEIVER (RX) To control the source: Plug IR Receiver into IR RX port of receiver unit; place receiver at or near display.
