SB60 airSOUND™ BASE USER’S GUIDE version 1.
CONTENTS WELCOME 2 PACKAGE CONTENTS The AirSOUND BASE SB60 3 AirSOUND BASE Controls & Indicators GETING STARTED 4 Remote control Sound Source / Setting memory FRONT GRILLE 6 GETTING THE BEST SOUND 7 CLEANING AND CARE 7 TROUBLESHOOTING 8 WELCOME Thank you for purchasing the Orbitsound SB60 airSOUND BASE. With proper use the airSOUND BASE delivers superb sound fidelity, engaging spatial sound, and will provide you with a fantastic listening experience for your TV, media and music.
The airSOUND BASE SB60 The Orbitsound airSOUND BASE SB60 is a single box TV sound system that delivers full range spatial sound for your living room. It is designed to work with your TV to give amazing, true and clear sound. The airSOUND BASE has 5 speakers. 2 front speakers that produce high definition mid and high frequencies, 2 side speakers that generate the spatial experience, and an integrated down-firing subwoofer that delivers strong bass.
2 GETING STARTED 1. TV SETUP 1 Position the airSOUND BASE under your TV. If your TV base is too large (bigger than 59cm wide), then the airSOUND BASE should be placed on a shelf below or above your TV. The airSOUND BASE can also be used without a TV as a sound system. 1 The airSOUND BASE is packaged with 8 anti-vibration/protection pads. If you experience vibration noise from your TV set during use, then use the pads as shown to help prevent this.
2. CONNECTING UP TV OPTICAL AUDIO OUT 1 2 1 Optical Aux Bluetooth 3 3 24 3 OPTICAL Spatial Soundbar with Bluetooth and Wireless Subwoofer ©2013 Orbitsound ltd. Model: M12 ON OFF AUX IN Approved components used WIRELESS CAUTION: To prevent electric shock, do not remove screws. No User serviceable parts inside. DC in 22V Made in China 1 2.5A 1 Stereo Line In 2 The best way of connecting the airSOUND BASE to your TV is with the included optical (TOSLINK) cable.
If your TV does not have optical: Use the included analogue cable to connect the audio output from your TV to the airSOUND BASE AUX 1 or AUX 2 inputs. You will need to change the source of the airSOUND BASE to AUX to hear this input. Note: Some TVs may only have a 3.5mm jack (headphones) output, you can also use this output. If your TV has no audio output, you can connect the optical cable to your set top box.
3 GETTING THE BEST SOUND 2 1 4 3 The airSOUND BASE is easy to set up and enjoy, but even better sound may be achieved by following these easy steps: Spatial Sound: The spatial sound field is produced by the speakers in the sides of the airSOUND BASE (2). These special signals interact with the main signal (1) to produce spatial sound in your listening environment. Make sure that the side grilles are free from obstacles.
TROUBLESHOOTING No sound: possible to reduce noise. Check power connections and that there is a continuous blue light on control panel. Digital optical issues: Check that the TV or other sound source is playing and that it is connected properly to the airSOUND BASE. If unsure that your media device is playing, unplug, and test with headphones. ‘Clicking’ or no sound Press the ‘source’ button on the remote control to change the sound source. The status LED (2) will flash when the source changes.
SPECIFICATIONS Frequency range +/- 3 dB [Hz] 38 – 16KHz Control; response (remote control) LF: +,-8dB subwoofer volume HF: 10KHz +/- 8dB EQ Maximum SPL [dB] 95dBA Amp. power 200W total Crossover frequencies [Hz] 220Hz Front main drivers 2x2” Orbitsound mk2 Spatial drivers 2x2” Orbitsound mk2 Sub-Bass driver 1 x 5” Enclosure types Front – asymmetric sealed Sides – sealed chambers Subwoofer – hybrid mode down firing.
ORBITSOUND LTD. +44 (0)8456 521 219 www.orbitsound.com/support support@orbitsound.
