Quick Start Guide

B-HYVE XR
SMART INDOOR/OUTDOOR
SPRINKLER TIMER
Quick Start Guide
TIMER INSTALLATION
CONNECT VALVE WIRES
CONNECTING TO WI-FI PROGRAMMING AND OPERATION
FUNCTION
FUNCTION
Manual Watering -
WATERALLZONES
Manual Watering -
WATERAZONE
Skip Zone
Cancel All
Watering
Rain Delay
Digital Lock-Out
Lights Off Mode
On/Off
Hard Reset
Hold until the display shows MANUAL
and flashes WATER ALL ZONES. To WATER
ALL ZONES for a default of 10 min. each*,
wait without pressing a button until WATER
ALL ZONES stops flashing and watering
will begin.
Hold until the display shows MANUAL
and flashes WATER ALL ZONES. Quickly
press two more times and WATER A
ZONE appears. Wait until WATER A ZONE
stops flashing and quickly press to select
the desired zone to run. When the zone
stops flashing the run time will begin to
flash. Quickly press to set the desired
run time. Once RUN TIME stops flashing,
watering will begin.
Quickly press to skip currently
running zone.
Hold between 2-5 sec.
Set in app; blinks yellow and display
shows DELAY.
Enable/disable in app.
Enable/disable in app.
Hold for 10 seconds.
Quickly press 5 times.
*Default watering time for “WATER ALL ZONES” can
be customized in the B-hyve App seings.
Hold until the display shows MANUAL
and flashes WATER ALL ZONES. Quickly
press again and WATER A PROGRAM
apears. Wait until WATER A PROGRAM
stops flashing and press to select the
desired program to run. Once the program
letter stops flashing, watering will begin.
Manual Watering -
WATERAPROGRAM
BUTTON PRESS
BUTTON PRESS
instructions continued on back
Select a location
Choose a location near power and away from direct sunlight,
if possible. This location should also have a good Wi-Fi signal.
You can check this using a smart phone. (Find a location that
has a minimum of two bars)
Prepare wire
Strip 1/2” (13 mm) of insulation from each wire.
Plug in your Orbit® B-hyve® timer
Once your B-hyve timer is plugged into the power source, it
will automatically look to pair with your smart device. The
will begin to blink blue. This indicates that your timer is ready
to pair with your smart device. Ensure that your smart device
has Bluetooth® turned on.
Connect to your Orbit® B-hyve® timer
Open your B-hyve app, create an account or login, and follow
the step-by-step process to add and set up your device. The
B-hyve app will connect to your device and you will, then, be
guided to connect to your home Wi-Fi network.
Programming the timer
The app has help screens and video to assist you with Wi-Fi
connections, programming, smart watering and other general
questions you may have.
Manual operation
All programming and full functionality of the timer are avail-
able in the B-hyve app. If you have the need, there are some
basic operations you can perform directly at your timer.
Connect to your Wi-Fi network
Select your network from the list and enter the password for
the network to connect your timer to your Wi-Fi signal. When
connected, the will illuminate solid white indicating a
successful pairing.
Connect wires
Push in one wire from each valve to a “Common” (COM) wire
and the other wires to a numbered terminal (only one wire per
terminal).
Mount the timer
Install a screw (included) into the wall. Use the expanding
anchors (included) for plaster, masonry or drywall installations.
Hang the timer on the installed screw using the keyhole
slot. Level the timer and use the second screw in one of the
preformed mounting holes to secure the timer.
Note: If you do not see your network name in the list, tap the
refresh buon in the app. If your network name still does not
appear, tap “Advanced” in the app and enter your network
name and password. The B-hyve App and the display windows
on the timer will assist you through the timer pairing and set-
up process.
Note: Your programmed schedules are stored both in the app
and on the timer. Watering will continue, if Wi-Fi connection
is lost.
Note: For optimum timer performance, connect the Wi-Fi to
recieve the lastest timer updates.
Note: We recommend you consult an
electrician for hardwired installations.
Note: If replacing a timer, it is helpful to take a photo of
the wires before you remove them from the old timer.
CONTENTS IN THE BOX
B-hyve XR Smart Sprinkler Timer
Mounting Screws and Anchors
Quick Start Guide
1. Strip Wire
2. Push In
Keyhole
Pre-formed
Mounting Holes
minimum signalindoor or outdoor
Printers are responsible
for meeting print
production requirements.
Any changes must be
approved by Orbit
®
.
Printed piece must meet
designated specifications
on this form.
© 2016 Orbit Inc.
This work is the property
of Orbit
®
, and cannot
be used, reproduced or
distributed in any way
without their express
permission.
Dieline
PMS
0000
Fold
PMS
0000
Product
Coverage
PMS
0000
Dims./
Callout
PMS
0000
∙
∙
∙
∙
Orbit
®
1.801.299.5555
orbitonline.com
M
Y
K
Glue
Folded Flat Additional Information
PRIN TERS ARE
REQUIRED TO MATCH
ALL SP ECIFIED
PMS COLORS.
C
DATE: 00/00/0000
DESIGNER: XX MARKETING: XX
SOFTWARE: Adobe Indesign CC
ARTWORK №: 00000-00 rX
L:
W:
H:
_._" W:
H:_._"
_._"
_._"
_._"
Printers are responsible
for meeting print
production requirements.
Any changes must be
approved by Orbit
®
.
Printed piece must meet
designated specifications
on this form.
© 2020 Orbit Inc.
This work is the property
of Orbit
®
, and cannot
be used, reproduced or
distributed in any way
without their express
permission.
Dieline
PMS
CG10
Fold
PMS
0000
Product
Coverage
PMS
0000
Dims./
Callout
PMS
7405
∙
∙
∙
∙
Orbit
®
1.801.299.5555
orbitonline.com
M
Y
K
Glue
Folded Flat Additional Information
PRIN TERS ARE
REQUIRED TO MATCH
ALL SP ECIFIED
PMS COLORS.
C
DATE: 01/14/2020
DESIGNER: QW MARKETING: MS
SOFTWARE: Adobe Indesign CC
ARTWORK №: 57985-50 rA
L:
W:
H:
_._" W:
H:_._"
_._"
_._"
_._"