Projector Flush Mount Universal projector flush ceiling mount User manual Model: OCM818W-RU / OCM818B-RU Patent Pending Optoma www.optoma.com Revision 24/01/2014 www.optoma.
IMPORTANT NOTES ● ● ● ● ● ● ● ● ● ● Thank you for purchasing the Projector Flush Mount. This bracket is suitable for most projectors up to a load of 15kg. To ensure correct usage, please read this instruction manual thoroughly. Keep this manual for future reference. Brackets should be mounted only be a qualified installer User will be responsible for any injuries and damages that may arise from improper installation and handing of Projector Flush Mounting Kit.
Ceiling Plate M4x6 Cross Recessed Screw M8x65 Socket Cap Screw Cross Recessed Screw A—I M5x10 Socket Button Screw Square Nut Extension Bracket (100mm) Extension Bracket (50mm) Bottom Spacer 1mm, 2mm, 4mm Washers SPECIFICATION Net Weight : Dimension : 420 x 200 x 120 mm (16.5” x 7.9” x 4.7”) Extendable Length (Min to Max) : Min 576mm, Max 826mm (Min 22.7”, Max 32.5” ) Load Capacity : 15 kg (33 lbs) 2.52 kg (5.
SAFETY Assembling without the correct use of bolts and screws at designated points may result in injury and damage to properties or the unit collapsing from its installed position. Should a malfunction occur disconnect the power from the main socket and surround the area with ropes to prevent others from getting near it. Check and ensure the ceiling where you install can support the weight or the projector and ceiling mounting.
PACKAGE OVERVIEW 1.
SETUP AND INSTALLATION (A) Removing the Ceiling Plate from the Flush Mount Assembly: 1. Loosen the M4x6 (x2) Cross Recessed Screw with a screw driver 2. Remove the M8x55 Socket Cap Screw and Nylock Nut from the Flush Mount Assembly as shown. 3. Removing the Ceiling Plate from the Flush Mount Assembly.
SETUP AND INSTALLATION (B) Installing the Ceiling Plate: Choose the appropriate installation procedure depending on your ceiling type.
SETUP AND INSTALLATION (C) Attaching the Flush Mount Assembly to the projector: C.1— Loosen the M5x10mm Socket Button Cap Screws using the 3mm Allen key until you can slide the extension brackets freely, as shown. Extension Bracket 100mm 3mm Allen key M5x10mm Socket Button Cap Screw C.2— Place projector’s Flush Mount Assembly over the projector and align the centre of the Flush Mount with the projector’s approximate Centre of Gravity.
SETUP AND INSTALLATION C.3— Place the Bottom Spacers in between the Extension Brackets and the Projector, and align the mounting holes as shown below. Extension Bracket Bottom Spacer Bottom Spacer Mounting hole NOTE If the mounting holes on your projector are recessed, you may need to use the additional spacers supplied in the parts bag. Please select the appropriate spacers according to the design of your projector.
SETUP AND INSTALLATION C.4— Select the correct Mounting Screws from the Parts bag and firmly screw the Flush Mount Assembly onto your Projector. Once this is done, the Projector Flush Mount Assembly is ready to be mounted onto the Ceiling Plate.
SETUP AND INSTALLATION (D) Attaching the Flush Mount Assembly to the Ceiling Plate D.1— Connect the Short Pole to the Ceiling Plate as shown be- Ceiling Plate Short Pole D.2— Insert the M8x55 Socket Cap Screw into the slot on the Ceiling Plate to lock the Flush Mount Assembly with the M8 Nylock Nut. Tighten the M4x5 Cross Recessed Screws to balance the Flush Mount Assembly.
SETUP AND INSTALLATION (E) Adjusting the Projector Roll / Shift Adjustments — to make Roll/Shift adjustments, first ensure the weight of the Projector is supported. Then loosen the M8x65mm Socket Cap Screw with the supplied 6mm Allen Key and adjust to your desired position. Re tighten the screws firmly. 6mm Allen Key M8X65mm Socket Cap Screw Roll Roll Shift Pitch Adjustment — to make Pitch adjustments, first ensure the weight of the Projector is supported.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 31.03.
www.optoma.