CRD-3301 SS08xxx Master Specifications Charging / Communication Cradle Product Name CRD-3301 Specification No T.B.D Edition Initial Date of Publication T.B.D Original Doc. No. T.B.D OPTOELECTRONICS Co., Ltd.
CRD-3301 SS08xxx Revision History Specification No.: T.B.D Product name : CRD-3301 Revision Date Section Description of Changes Initial T.B.
CRD-3301 SS08xxx Table of contents 1. Abstract ·····································································································1 2. Overview ···································································································1 3. Basic Specifications···················································································2 4. Bluetooth ···································································································4 5.
CRD-3301 SS08xxx 1. Abstract This manual provides the specifications for the charging / communication cradle, CRD-3301. 2. Overview CRD-3301 is the dedicated charging / communication cradle for the laser handy scanner, OPR-3301. Followings are the features of the CRD-3301: ・CRD-3301 receives data from OPR-3301 via ver.2 compliant Bluetooth interface. ・The cradle can output the received data via RS232C or USB interface. ・OPR-3301 can be charged by placing it on the CRD-3301.
CRD-3301 SS08xxx 3. Basic Specifications Control Section Item CPU Clock frequency Specification 16bit CMOS CPU 12.00MHz Remark FLASH ROM 256KB For BIOS/DATA Communication Section RS-232C: 600bps to 57.6kbps Interface USB: 2.0 HID compliant 2400MHz to 2483.5MHz Bluetooth Ver2.0 compliant Class 2 (4dBm or less) Installed SPP Communication range 10m The distance may vary depending on the environment. Baud rate 57.
CRD-3301 SS08xxx Environment specifications Operation Storage Operation Storage Drip proof 0 to 40% -20 to 60% 25 to 85% 20 to 90% Increased the frequency of vibration from 10Hz to 100Hz 2 at an accelerated velocity of 19.6m/s (2G) for 6 minutes each in X-direction, Y-direction and Z-direction. Repeated this test for 10 times in each direction. Dropped from a height of 75cm onto a concrete surface. The drop test is done for each side (right, left, front, back, top and bottom).
CRD-3301 SS08xxx 4. Bluetooth CRD-3301 uses Bluetooth as a wireless interface. Blue tooth is compliant with ver.2.0 and supports SPP (Serial Port Profile).
CRD-3301 SS08xxx 5. Detailed View Figure1: Detailed view No.
CRD-3301 SS08xxx 6. Electrical Specifications 6.1. Configurations of CRD-3301 CRD-3301 is the dedicated cradle for OPR-3301 scanner which is able to charge and communicate with the scanner. This product consists of a power supply section which uses Bluetooth interface, power section which is in charge of power feed and voltage conversion for the scanner.
CRD-3301 SS08xxx 7. DIPSW configurations Following functions can be set by DIPSW as shown. DIPSW No. DIPSW1 DIPSW2 DIPSW3 DIPSW4 DIPSW5 DIPSW6 Note: Function Make sure the it is always OFF when using the cradle. This will be used for feature expansion. Enables inquiry scan withiout security Connection can be made witout authentication. Disables protocol while in connection. The menu allows the cradle to connect to bluetooth devices including OPR-3301. Disable DTR signakl detection for the host.
CRD-3301 SS08xxx 8. Cable Interface CRD-3301 supports RS232C and USB HID interfaces. The cradle recognizes the interface whilst watching its power supply. * When changing an interface, turn OFF the power and change the setting for access point of the scanner and read the BD address. Otherwise it may cause malfunctions such as connection and data transmission failure. 8.1. RS232C Interface 8.1.1.
CRD-3301 SS08xxx 8.1.4. Interface Circuit Figure4: Interface circuit 8.1.5. Character Format Figure5: Character format 8.1.6. Communication Format Figure6: Communication format 8.1.7. Communication Control By reading menus listed below enables the cradle to communicate with host computer. Settings information is sent from the scanner. BUSY/READY and P5 are set as default.
CRD-3301 SS08xxx a) No hand shaking The scanner attempts the communication regardless of the state of the host computer. Flow control is not executed for the Bluetooth interface. For the scanner (OPR-3301), RTS is always enabled. Figure7: No Handshaking b) BUSY/READY The scanner and the host computer notify each other of their state and whether they can receive data with BUSY/READY through an RTS line. They can communicate state to each other through a CTS line when connected as in the following figure.
CRD-3301 SS08xxx Flow Control Time Out Indefinitely (default) 100msec 200msec 400msec Menu / Command I0 (Indenfinitely) I1 I2 I3 Figure 9: Cannot receive command CTS / TXD Signal Timing When the CTS line (RTS signal of the host) is turned OFF while sending a TxD signal, the scanner transmits one character and waits. When the CTS signal is turned ON while transmitting a character, the character will be transmitted.
CRD-3301 SS08xxx c) Modem The scanner turns CTS line ON before transmitting data. Other processes are the same as BUSY/READY. Figure 11: Hand shaking modem mode d) No ACK/NAK After data has been transmitted, the cradle transmits ACK to the host to notify the transmission status on the wireless communication line. * Between the cradle and the host: No control.
CRD-3301 SS08xxx e) ACK/NAK After the data transmission, the cradle expects to receive one of the following responses from the host: ACK/NAK Protocol Response ACK NAK DC1 Timeout Control Level Scanner, Cradle and Host Notes Monitors response from the host.
CRD-3301 SS08xxx f) ACK/NAK NO RESPONSE When no response from the host is received within the set time, the cradle assumes an ACK response, and returns to the initial state without the error buzzer. The other actions are the same as ACK/NAK. Response Timeout Menu / Command Cradle None Scanner Green Light with GR Buzzer None Receive Timeout Menu / Command XI4 Indefinitely XI5 100 ms (default) XI6 500 ms XI7 1000 ms 8.1.8.
CRD-3301 SS08xxx 8.2.4. Interface Circuit Figure 13: Interface circuit 9. Interface Cable Both a RS232C cable and a USB cable are included for a package. 9.1. RS232C Cable A dedicated RS-232C cable is packaged in a box with CRD-7734. Cable model no.: B04009-05 9.2. USB Cable Cable model no.: B03006-11 10.
CRD-3301 SS08xxx 11. Serial Label The serial number shown below is affixed to the cradle.
CRD-3301 SS08xxx 12. Packaging Specifications 12.1. Individual Packaging Specufuactions Size of the package: 163 (W) × 252 (D) × 123 (H) (mm) *T.B.D Figure 15: Individual packaging specifications 12.2. Collective Packaging Specufuactions Size of the package: 260 (W) × 830 (D) × 255 (H) (mm) *T.B.
CRD-3301 SS08xxx Vibration test: Increase the frequency of the vibration from 10 Hz to 100 Hz with accelerated velocity 19.6 m/s2 (2 G) for 60 minutes in non-operating state. Repeat this routine in each X, Y, Z direction once for 60 minutes each. 14. Reliability Parameter MTBF Number of Contact Number of operation Tested Parts Current-carrying parts Power supply terminal Lever switch Life 7 years 1,000,000 times 100,000 times 15. Warranty 15.1. Warranty Period OPTOELECTRONICS Co., Ltd.
CRD-3301 SS08xxx 17. RoHS RoHS: The restriction of the use of certain hazardous substances in electrical and electronic equipment, 2002/95 EC. 18. Precautions 18.1. Radio Low The data collector has obtained the Certification for Construction Design of Specified Radio Equipment. Therefore it does not need to have a radio station license in Japan.
CRD-3301 SS08xxx 19. Bluetooth To communicate via Bluetooth, the device which CRD-3301 is connected to must support the same Bluetooth version and profile as CRD-3301’s. ・ CRD-3301 is compliant to Bluetooth standards. However, we cannot assure the connection between CRD-3301 and other Bluetooth devices which have not been tested. ・ Bluetooth supporting devices use 2.4 GHz frequency band. However, many other sorts of devices also utilize this frequency band.
CRD-3301 SS08xxx Appendix.
