OPR-3101 Wireless 1D Scanner Simple Intruction manual OPTOELECTRONICS Co.,Ltd.
1.
2.Detailed view 2-1. OPR-3101(Scanner) ⑥ ③ ① ⑧ ② ⑨ ⑪ ⑦ ⑩ ④ OPR-3101 Detailed View Name 1. Window 2. Trigger switch 3. Indication Panel 4. Lock for Battery Lid 5. Terminal for charging 6. Hook 7. Charging terminal 8. Buzzer sound hole 9. Model name label 10. Serial number label 11. Laser caution label Function Through the laser output and receive catoptric light from Barcode. Scanning barcodes, connecting / disconnecting Bluetooth .
2-2. CHG-3101 ④ ⑤ ⑦ ① 114.
2-3. CRD-3101 ④ ⑤ ⑦ ① ② ③ 114.
Name 2. Power supply LED 2. Indication LED for wired data line 3. Indication LED for wireless data line 4. Terminal for power supply and Detector 5. Charging LED 5. Battery charger 7. Scanner detection switch 8. DC Jack 9. Plug-in phone jack 10. USB connector 11. Model name label 12. Dip switch 13. BD address label 14. Reserved 15.
2-4. Dip switch settings Dip switch located on the bottom of CRD-3101 Please follw the chart shown below DIP SW SW1 SW2 SW3 FUNCTION Invalid No security. Incwairi is effective. Opto protocol is invalid. SW4 The detection of the DTr signal is invalid. SW5 Initialization (Shipment setting) SW6 Software down load mode REMARKS Please use it with remaining power-off mode. It can connect without authentication. It must disable SW3 in case of connect Bluetooth devices except Scanner.
3.For use 3-1.About the scanner The charging battery pack is shipped without attaching the scanner. Please attach the charging battery pack to the scanner. As soon as attaching cradle or charger to the scanner, it will operate automatically ---Red LED, the status indicator lights. Also, when charging finishes, it becomes waiting mode.
3-2 About the charging cradle CHG-3101 is specialized charger for OPR-3101. CHG-3101 is not only able to charge the scanner, but also the charging battery pack. ・LED display of the cradle Code LED display Powrer Supply LED color red red Charging LED ― green green/red Remarks It lights when the battery is not fully charged.
3-4.Charging time As for CHG-3101/CRD-3101,l the battery connected to the cradle isn’t charged while the scanner is charged. Spec. Approx. 5 hours Approx. 10 hours AC supplying mode Remarks AC adopter drive The time needed for fully charging the empty battery USB Hi-Power drive 7.Charging times of CRD-3101/CHG-3101 3-5.How to change the battery pack. <Process> 1.Turn the screw of the bottom of the grip end anti clockwise with like a 1-Euro sized coin. 2.Open the lid and take out the old battery.
5.Connection of wireless communication system, Wireless specifications OPR3101 employs the Bluetooth (ver. 2.0 compliance) as a wireless interface. It is capable of communicating with the devices with similar profiles owing to SSP correspondence. ■Data sending outputs Class 2 ■the structure of connection 1:1 (*1:N is not supported.
■Connecting authentication settings Settings for authentication settings Please complete to enter the pin code with 30 seconds due to the time limit of the authentication system. ※ Please set the PIN code before connecting with authentication. ※It may be a need to enter the pin code connecting with authentication. Then please enter the code again. ※You don’t need to enter the Pin code when connecting without authentications. 6.Connecting and disconnecting process 6-1.Connecting process CRD-3101 1.
7. Settings for shipping The menu barcodes of scanner, communication and connection make settings easy. Therefore there are menu barcodes for the default settings. Default setting menu is set before shipping.
8.Menu barcodes for settings Connection / disconnection settings for OPR3101 8-1.How to set When scanning the same setting items, the item most recently scanned is effective. Order 1 2 3 Menu barcodes for scan Scan the SET (zz)barcodes Scan the optional barcodes. Scan the END (zz)barcodes 8-2.Default settings The setting the place it back to the settings for shipping.
8-4.Control settings for wireless output measurement The scanner keep sending and receiving status by setting the scanner with the items as below and that make various wireless performance measurement easy.
※Command numbers 1 to 6 can scan directly without settings by start/end ZZ codes. After scanning these numbers , the commands keep operating as long as the red and green LED blink. Press the trigger button to release the command. ※There’s a need to scan start/end ZZ codes concerning command 8 to 15. ※ For example, you can confirm the RF output with read few RF-test Barcode combination. Confirm the Non-Modulation, Non-Hop and AHF with under condition.