CRD9823-RU Data Collector Cradle Specifications Manual
Opticon CRD9823-RU Specifications Manual All information subject to change without notice. Document History Model Number: CRD9823 RU Specification Number: Edition: 1 Original Spec Number: Date: 2014-01-03 Copyright 2014 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon.
Opticon CRD9823-RU Specifications Manual Contents 1. Abstract ................................................................................................................................. 5 2. Overview ............................................................................................................................... 5 3. Physical Features ................................................................................................................. 5 3.1. Dimensions ......................
Opticon CRD9823-RU Specifications Manual Table of Figures Figure 1: DIP switch settings ..................................................................................................... 8 Figure 2: Signal timing when software is configured .................................................................. 9 Figure 3: RS-232C cable......................................................................................................... 10 Figure 4: USB cable ..............................................
Opticon CRD9823-RU Specifications Manual 1. Abstract This manual provides specifications for the CRD9823-RU cradle designed for the Opticon OPL (OPL97XX and OPL98XX) series data collectors. The CRD9823-RU cradle supports USB and RS232 interfaces and can also used to charge the OPL. 2. Overview The CRD9823-RU cradle can be used to charge the OPL series data collectors. Additionally, it provides a way for data communication between the OPL data collector and a host computer.
Opticon CRD9823-RU Specifications Manual 5. Electrical Specifications Only use dedicated Opticon approved AC adapters with this cradle. The output of such a AC adapter should be 6V/2A. It is not possible to power the cradle via USB. 5.1. Absolute Maximum Ratings Parameter Value Unit Power supply voltage (VCC to GND) -0.3 to 6.5 V Input voltage (D+, D-) -0.5 to 0.5 V Input voltage (RS-232C IN) ±30 V Input voltage (RS-232C OUT) ±15 V 5.2.
Opticon CRD9823-RU Specifications Manual 6. Interface Specifications 6.1. External Interface Connector and Pin Assignment 6.1.1. DC Power Supply Connector (EIAJ Type 3) Pin Signal Name Notes Inward +6 V Power supply +6 V Outward GND Ground 6.1.2. Connector for USB on PC Side (USB Type B) Pin Signal Name I/O Notes 1 VBUS P USB bus power supply 2 D- I/O Data - 3 D+ I/O Data + 4 GND P Ground 6.1.3.
Opticon CRD9823-RU Specifications Manual 6.2. Communications Interface The baud rate can be configured via DIP switches on the bottom of the cradle. The baud rate can also be configured by using special software on the host. 6.2.1. Baud rate Configuration using DIP switches To disable software configuration, set SW4 to OFF. Baud rate can be configured using SW1–SW3 as listed in the table below. DIP Switch Baud rate SW1 SW2 SW3 SW4 115.2 kbps ON ON ON OFF 57.6 kbps OFF ON ON OFF 38.
Opticon CRD9823-RU Specifications Manual 6.2.2. Baud Rate Configured Using Software To allow configuration using software on the host computer, set SW4 to ON. The other DIP switches are not used when SW4 is ON. CTS Line DSR Line Baud Rate Remarks Edge 0 pulse 115.2 kbps Reset Pulse Count 1 pulse 57.6 kbps 2 pulse 38.4 kbps 3 pulse 19.
Opticon CRD9823-RU Specifications Manual 7. Cables and Connectors 7.1. RS232-C Cable Figure 3: RS-232C cable Type: Straight Diameter: φ3.8 ±0.15 mm Length: 1500 ±100, -0 mm Cores: 8 insulated wires, 1 conductive wire Left RJ50 (10-pin modular jack) Right DB9, female Connectors 7.2. USB A-B Cable Figure 4: USB cable Type: Straight Diameter: Φ4.7 ±0.
Opticon CRD9823-RU Specifications Manual 8. Labels The serial number shown below is affixed to the specified location on the cradle. 8.1. Product label Figure 5: Product label on the bottom of the cradle 8.2.
Opticon CRD9823-RU Specifications Manual 9. Packaging Specifications 9.1. Individual Packaging Put the cradle in a protective foam bag and place it in an individual packing box.
Opticon CRD9823-RU Specifications Manual 9.2. Collective Packaging Figure 8: Collective packaging specification Note: The “RO” mark labeled on the package tray or package box guarantees that the applicable product has passed our test of RoHS restrictions compliance (the restriction of the use of certain hazardous substances in electrical and electronic equipment, 2002/95 EC). However, this document does not have any legal weight in the European Union.
Opticon CRD9823-RU Specifications Manual 10. Regulatory Compliance 10.1. EMC EN55022 EN55024 FCC Part 15 Subpart B Class B: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 10.2.
Opticon CRD9823-RU Specifications Manual 11. Safety recommendations Handle this product carefully. Do not subject it to any of the following. Shock • Do not throw or drop the cradle. • Do not place heavy objects on the cables. Temperature Conditions • Do not use the cradle at temperatures outside the specified operating temperature range. • Do not subject the cradle to temperatures outside the specified storage temperature range. • Do not forcibly bend the cables, especially at low temperatures.
Opticon CRD9823-RU Specifications Manual 12. Mechanical Drawings Dimensions: W 98.5 x D 71.5 x H 67.0 mm Figure 9: Mechanical drawing No.