User's Manual

ManualsBrandsOpticon Sensors Europe ManualsElectronicsPortable Data Terminal

OPTICON

User's manual

PHL-7000 series

RSS-expanded Enable RSS-expanded

DataMatrix

ECC000-ECC140

Enable DataMatrix ECC000-ECC140

DataMatrix ECC200 Enable DataMatrix ECC200 (default)

Aztec Enable Aztec (default)

Aztec Runes Enable Aztec Runes

QR Code Enable QR Code (default)

Maxi Code Enable Maxi Code (default)

PDF417 Enable PDF417 (default)

MicroPDF417 Enable MicroPDF417 (default)

Table 3-17 Code configure description 2D CMOS

3.2.1.3 Prefix and suffix TAB

With these options alterations can be made to the format of the transmitted data string.

Figure 3-2 Prefix and Suffix Tab

Options available are :

- Transmission of a preamble,

- Transmission of a prefix,

- Transmission of a suffix,

Summary of content (13 pages)

PAGE 1
OPTICON User's manual PHL-7000 series RSS-expanded Enable RSS-expanded DataMatrix ECC000-ECC140 Enable DataMatrix ECC000-ECC140 DataMatrix ECC200 Enable DataMatrix ECC200 (default) Aztec Enable Aztec (default) Aztec Runes Enable Aztec Runes QR Code Enable QR Code (default) Maxi Code Enable Maxi Code (default) PDF417 Enable PDF417 (default) MicroPDF417 Enable MicroPDF417 (default) Table 3-17 Code configure description 2D CMOS 3.2.1.
PAGE 2
OPTICON User's manual PHL-7000 series - Transmission of a postamble. The transmitted string format is : Figure 3-2 Transmitted string format A prefix and suffix of maximum 4 direct input entries each may be included in front and at the end of the string respectively. A preamble is transmitted before the prefix and can contain up to 8 direct input characters. A postamble is transmitted after the suffix and can contain up to 8 direct input characters.
PAGE 3
OPTICON User's manual PHL-7000 series In the Prefix and Suffix option, 4 key input fields and their current settings are shown : Figure 3-2 Prefix option Figure 3-2 Suffix option The default suffix is ^M (CR) .
PAGE 4
OPTICON User's manual PHL-7000 series In the code option field can be indicated for which symbology the current prefix or suffix should be configured. The “Clear All Codes” options will clear the prefix for all symbologies. Figure 3-2 Prefix : Code list box. Example : to set the characters “UPCA” for bar code symbology UPC-A, tap in the “Direct Input Keys” section, the field “1st Key Input”. A list box will popup, which shows all 128 ASCII characters. SPACE is the character (ASCII 32dec, 20hex).
PAGE 5
OPTICON User's manual PHL-7000 series Figure 3-2 Prefix : Direct input keys selection box.
PAGE 6
OPTICON User's manual PHL-7000 series Thereafter the display will look like : Figure 3-2 Prefix : Selected character ‘U’for UPC-A.. Repeat these steps for the characters ‘P’, ‘C’and ‘A’. Thereafter the display will look like : Figure 3-2 Prefix : Selected characters ‘UPCA’for UPC-A.. If the bar code reader reads an UPCA label with data ‘071589812309’, it will be send to the application as : ‘UPCA071589812309’where is the default suffix ASCII character .
PAGE 7
OPTICON User's manual PHL-7000 series Preamble and postamble are applicable for all bar code symbologies. Therefore the code option list box shows only 1 option : “Clear all codes”. Figure 3-2 Preamble : Only 1 code option.
PAGE 8
OPTICON User's manual PHL-7000 series 3.2.1.4 Quiet zone TAB With this option the reader can decode bar codes that have smaller start and/or end margins than specified for the symbology. Be carefully when using this option. It may increase the possibility of partial reads and ghost reads. Do not use smaller margin checks then necessary. If possible replace the bar code labels by ones that have correct start and end margins. Figure 3-2 Quiet zone options.
PAGE 9
OPTICON User's manual PHL-7000 series 3.2.1.5 Read Mode TAB With this option several read modes can be changed. Figure 3-2 Read mode options. Field name Description Trigger repeat This option makes it more easy to select a single bar code from a sheet filled with barcodes. If the trigger switch is pressed once, the laser beam is on during the configured read time. The laser beam can now be moved to the required bar code. If the trigger switch is pressed again, the bar code is decoded and transmitted.
PAGE 10
OPTICON User's manual PHL-7000 series Positive / Negative bar codes Read 1 time Redundancy = 0 Read 2 times Redundancy = 1 (default) Read 3 times Redundancy = 2 Read 4 times Redundancy = 3 Usually bar codes are printed black on white, but sometimes white on black. These labels are called positive and negative respectively. In case the ‘negative bar codes’option has been selected, positive labels may not be decoded or with difficulty.
PAGE 11
OPTICON User's manual PHL-7000 series Example : To set a prefix ‘Test’for UPC-A, lookup in Opticon’s Universal Menu Book (UMB) the serial command’s of : - prefix UPC-A : see UMB paragraph 4.2.1, serial command = N1 - Direct input ‘T’: see UMB paragraph 4.3.4, serial command = 0T - Direct input ‘e’: see UMB paragraph 4.3.5, serial command = $E - Direct input ‘s’: see UMB paragraph 4.3.5, serial command = $S - Direct input ‘t’: see UMB paragraph 4.3.
PAGE 12
OPTICON User's manual PHL-7000 series 3.2.2 Bluetooth Device Properties ICON ITEM & FUNCTION • ü “Scan Device” Tab ( Figure 3-25) : Tap the Scan Device button to initiate a scan for Bluetooth devices. The Bluetooth manager lists the Bluetooth devices that it finds, see Figure 3-26. If Bluetooth hardware is not found in the PDT, the Bluetooth Hardware Error window ü ü appears, see Figure 3-27. Table 3-18 described the Bluetooth Icons. Double tap the device to connect to on the device list.
PAGE 13
OPTICON User's manual PHL-7000 series Figure 3-25 Bluetooth Manager Window Figure 3-26 Bluetooth Manager Window Figure 3-27 Bluetooth Error Window Figure 3-28 Bluetooth Manager Window Figure 3-29 Bluetooth Enter PIN Window Figure 3-30 Bluetooth Manager Window 3-19