User’s Manual Laser Terminal PHL 2700 Cradle IRU 2700
USER’S MANUAL PHL2700 TERMINAL / IRU2700 USER’S CRADLE CAUTION: This user’s manual may be revised or withdrawn at any time without prior notice. Limited warranty and disclaimers By opening the package of this product you agree to become bound by the liability and warranty conditions as described below. Under all circumstances this manual should be read attentively, before installing and or using the product.
USER’S MANUAL PHL2700 TERMINAL / IRU2700 USER’S CRADLE 2.1 UNPACKING 66mm 41mm Apart from the terminal or cradle, additional items might be ordered and supplied. If there are any missing parts please contact your supplier. 31mm INSTALLATION 2.2.
USER’S MANUAL PHL2700 TERMINAL / IRU2700 USER’S CRADLE Description of the function keys 2.2.3 Display of terminal In the shift mode, back light on/off, contrast adjustment, and cursor movement can be done by these keys. (The user’s application can give different definitions to the keys) The liquid crystal display of the terminal is typically used to show program prompts, instructions and data, as defined in the user’s application.
USER’S MANUAL PHL2700 TERMINAL / IRU2700 USER’S CRADLE 2.3 HANDLING PRECAUTIONS Use of the terminal Operate the terminal keys by pressing them lightly with your fingertips or with something soft and round. Pressing the keys with a sharp pointed object (for eg. a ballpoint) can damage the keys.
USER’S MANUAL PHL2700 TERMINAL / IRU2700 USER’S CRADLE 2.5 INSTALLING, REPLACING AND CHARGING BATTERIES 2.5.1 Required batteries The terminal needs both main battery and backup battery for operation. Wrong use of batteries might cause serious damage to the terminal or to the cradle. ! ! Insert full batteries before use of the terminal. Never remove the main battery pack while the terminal is turned on. Doing so can cause data in the terminal to be deleted.
USER’S MANUAL PHL2700 TERMINAL / IRU2700 2.5.5 How to (re)place the main battery in the terminal? ! ! USER’S CRADLE MANUAL PHL2700 TERMINAL / IRU2700 CRADLE 2.5.6 How to (re) place the backup battery in the terminal? 1 ! ----> open Only use batteries as specified in paragraph 2.5.1. If you have data stored, make sure the backup battery is placed and full enough, to avoid data loss. ! Before installing a battery case with penlite batteries: Make sure you use the right battery size.
USER’S MANUAL PHL2700 TERMINAL / IRU2700 USER’S CRADLE 2.6 INSTALLING IN A SYSTEM 2.6.1 Terminal to computer PHL 2700 ! ! ! ! Turn off your devices before installation. Because of the special pin-out of the connectors, use the cables supplied by the manufacturer. When you need another cable for a certain device, that is not supplied, contact your supplier to purchase the right cable. In case another cable is used, take notice of the pin-out specifications further in this manual.
USER’S MANUAL PHL2700 TERMINAL / IRU2700 USER’S CRADLE ! 3 4 SCANNING MANUAL PHL2700 ! ! Fit the bar code in the laser beam from margin to margin and pass the scanner downward over the bar code, as shown in the scan position illustration. 3 5 5.2 RS485 cable for cradle network IRU2700 Please make sure that the terminal is installed according to the installation instructions. 4.1 How to read the barcode The scanning sequence is defined by the user’s application.
USER’S MANUAL PHL2700 TERMINAL / IRU2700 USER’S CRADLE 6.1.2 Optical specifications 3 6 Light source 650 nm visible laser diode Scan rate 100 scans/sec Decode rate 100 decodes/sec Reading width 62 mm at 30 mm 111 mm at 100 mm Transmission speed RS232 direct cable: 2400 - 115200 baud RS232 cradle: 2400 - 115200 baud IrDA terminal: 2400 - 115200 baud MANUAL PHL2700 0 - 140 mm (at PCS 0.9, res. 0.25) SPECIFICATIONS 6.1 SPECIFICATIONS TERMINAL 6.1.
USER’S MANUAL PHL2700 TERMINAL / IRU2700 USER’S CRADLE MANUAL 7.1 COMMUNICATION PROBLEMS 3 7 No communication from the cradle to the device, or data is transmitted distorted or corrupted. TROUBLE SHOOTING This chapter contains information on solving problems you may encounter when using the terminal and/or cradle. If problems occur, first carry out some general checks, before verifying the problem with the descriptions in this chapter.
USER’S MANUAL PHL2700 TERMINAL / IRU2700 USER’S CRADLE MANUAL PHL2700 TERMINAL / IRU2700 CRADLE 7.3 TERMINAL PROBLEMS Terminal does not respond to key presses, while the display stays on. ? ? Message “Application halted” or “No application installed” is shown. There is no user’s application for PHL2700 loaded in the terminal. Contact your supplier. For example pressing the shift key does not toggle the shift indicator. There is a flaw in the application program.
Opticon Article Code O0220000022 Opticon user's manual 24