Opticis Optical USB Extension Module (M2-100 User’s Manual)
Contents Precautions 1. Package Content 2. Introduction 2.1 Function 3. Installation 3.1 Set-up 3.2 Connection 4. 5. Trouble Shooting Specifications 5.1 Opticis Optical USB Extension Module 5.2 AC-To-DC 6.
Precautions WARNING Do not dismantle the housing or modify the module. Dismantling the housing or modifying the module may result in electrical shock or burn. Refer all servicing to qualified service personnel. Do not attempt to service this product yourself as opening or removing housing may expose you to dangerous voltage or other hazards. Keep the module away from liquids. Spillage into the housing may result in fire, electrical shock, or equipment damage.
1. Package Contents 1.1 Opticis Optical USB Module Module(M2-100) 1.
2. Introduction Our Optical USB Extension Module M2-100 links the USB signal up to 50 meter without any repeater. 2.1 Function - Application with self-powered - One Up-Stream Module, A Socket, One Down-Stream Module - Compatible with USB 1.1 (12Mbps, 1.
3. Installation 3.1 Set-Up - Hard Ware Condition : PC applied by USB ports. - Soft Ware Condition : Window 98, Window Me, Windows 2000 - AC-To-DC Adapter Requirements : 5 V, 600mA (Core is 5 V) 3.2 Connection - Connect M2-100 with the adapter. - Connect “A” plug in M2-100 with PC’s USB ports(Figure.1) - Connect USB peripheral device(key board, mouse, camear Etc) with USB downstream port(A Receptacle) (Figure.
4. Trouble shooting If you are to check out its functioning, pls take action as below. When a problem is found, apply the suggested remedies on the next page. 1. Select the menu “Start “ from Window. 2. “Setting”à“Control Panel”, and then double-click “System”. 3. Select the tab “ Device Manager”. 4. Make“ USB Controller” expanded by clicking “+” next to “ USB Controller” in “Device Manager” (If this item is not, pls refer to problem #1 from the solution table.) 5. Click and select “General USB Hub”.
* Solution Table * N O Problems Expected Causes Suggested Remedies “USB Controller” is not installed. Your Window system does not apply for USB. Contact PC manufacturer and request them to reinforce USB function. Our product, M2-100 is not connected rightly. 2 “General USB Hub” is not installed by operation system. Check if downstream port is rightly power-connected and then connect it again after pull-off upstream cable. 3 Opticis Optical USB Extension Module does not work.
5. Specifications 1) Opticis Optical USB Module (M2-100) Size (Width x Length x Height) Up-stream: Down-stream: Length (Whole): Packaging: Weight: Net weight : Gross weight : Power input 5V DC 600mA Speed High: 12Mbps Low: 1.5Mbps 2) Power – Adapter Power input: A.C- 100~240 V, 5060Hz 0.
6. Warranty •1 (One) Year Warranty • Warranty Limitation and Exclusion Opticis shall have no further obligation under the foregoing limited warranty if the product has been damaged due to abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized modifications, tampering, alterations, or service other than by Opticis or its authorized agents, causes other than from ordinary use or failure to properly use the product in the application for which said product is intended.
* FCC LABELLING REQUIREMENTS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations.
INFORMATION TO THE USER INFORMATION TO THE USER This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
