Ver. 2.01 WWW.OPTICIS.
Contents Welcome! .............................................................................................................................................- 3 Product Description ..............................................................................................................................- 3 Shipping Group ....................................................................................................................................- 3 Supporting Resolutions .........................
Welcome! Congratulations on your purchase of the Wireless Extender for HDMI, Keyboard and Mouse, HDWX-100-TR. This manual contains information that will assist you in installing and operating the product. Product Description The OPTICIS wireless Extender, HDWX-100-TR is designed for wireless signals extending of HDMI, keyboard and mouse. The transmitter module HDWX-100-T connected to the HDMI source encodes the HDMI by H.264 and transmits the signal via advanced Wi-Fi, 802.11a/n technology.
800x600p60 1024x768p60 1280x768p60 1280x960p60 1280x1024p60 1600x1200p60 1920x1080p60 Note: Some PC resolutions may not be displayed properly. Applications Home AV KVM Video Control room Digital signage Medical imaging Systems Requirements for Setup Hardware requirements You must have a HDMI graphic controller or card having a HDMI or DVI port in your PC or any other equipment being used.
Installation Important: Please keep the installation procedure below. Improper or no operation may result if the start-up sequence is not followed correctly. Note: If you change a source to another source such as PC, Camcorder, DVD Player or Blu-ray player, you have to reset the power of all TXs and RXs by re-plugging of the +5V power adaptor. Step 1 Carefully unpack the contents of the shipping group. Step 2 Connect HDWX-100-T to the HDMI source by supplied HDMI cable.
Fig. 2: Configuration of Receiver, HDWX-100-R LED Indication HDWX-100-T and HDWX-100-R have two (2) LEDs for Power and Wireless status located on the top. • Power status LED (Blue) When power is applied, the blue LED will be turned on. • Wireless status LED HDWX-100-T and HDWX-100-R are starting to connect each other, the blue LED will be blinking approx.10~15sec. When it is completed, it will stop blinking and be turned on.
Note: (S) means press shortly and release the button, (L) means press the button and hold for 2~3sec and release the button. Note: Basically, GUI is operated on the receiver side and it shall be operated in cases as below; (1) When you connect the transmitter and receiver for the first time (2) To change another transmitter to be connected (3) To change general setting or check system information In case of (1) or (2), the receiver can be connected to the transmitter using PBC button.
To select a menu, press [M] button. To return the main menu, press and hold [M] button for 2~3sec. To move to the right, press [▶] button. Step 3 Connectivity menu: To connect to the other transmitter. Step 3-1-1 PIN method for connectivity [default] If user want to find a transmitter to connect or change the other transmitter, press [▼] button to select and press [M] button to connect the transmitter. Then, the message is shown as below and the connection is completed.
Note: When the connection is completed, it exits from GUI menu automatically. Step 3-2 Disconnection To disconnect the transmitter, press [▶] button. To exit from GUI menu, press and hold [M] button for 2~3sec. To return to the previous page, press and hold [▶] button for 2~3sec. If user press [M] button, all the transmitter information will be deleted. In order to connect new transmitter, execute the Step 3-1-1 or 3-1-2 again. To exit from GUI menu, press and hold [M] button for 2~3sec.
Select one of menus to be used from by pressing [▼] and [M] button. User can edit the name in ‘New title’ by selecting the characters as below. Press [▶] and [▼] buttons to move and press [M] button to select it. Then, press Complete to save the name. To exit from GUI menu, press and hold [M] button for 2~3sec. To return to the previous page, press and hold [▶] button for 2~3sec. Step 4 General Setting menu Press and hold the [M] button for 2~3sec to enter GUI menu.
There are four (4) sub menus in General Settings, Latency Mode, Wireless Channel, WPS method and Black Screen Mode as shown below. Step 4-1 Latency Mode User can select Theater mode or Game mode. Game mode has lower latency than Theater mode. To exit from GUI menu, press and hold [M] button for 2~3sec. To return to the previous page, press and hold [▶] button for 2~3sec. Step 4-2 Select Wi-Fi Channel User can change channel among Auto, CH1, CH2 and CH3.
Step 4-3 WPS Method User can select PIN Code or PBC Button. In case of PBC Button mode, user needs to press PBC button on the TX side for pairing. To exit from GUI menu, press and hold [M] button for 2~3sec. To return to the previous page, press and hold [▶] button for 2~3sec. Step 4-4 Black Screen Mode User can select Black Screen mode or last image mode when this menu is disabled To exit from GUI menu, press and hold [M] button for 2~3sec.
Step 5 System Info menu Press and hold the [M] button for 2~3sec to enter GUI menu. After selecting System Info, press [M] button. To exit from GUI menu, press [M] button for 2~3sec. There are 2 sub menus in System Info, Signal Strength and System Information as below. Step 5-1 User can monitor the current Signal Strength of the receiver as below.
Step 5-2 User can check the information of transmitter and receiver such as IP address and MAC address as below. Product Specifications Designed in a small shape with plastic enclosure so as to directly hook up the PC or display Wi-Fi Standard: 802.11n, 5GHz, 2x2 MIMO, two internal antennas (Maximum Throughput: 300Mbps) Supports WPA/WPA2 and QoS Video Resolution: up to 1920x1080 at 60Hz Audio: 7.1CH surround Supports H.264 for codec HDMI 1.3 and HDCP2.0 DVI 1.
Storage Temperature: -20~60°C Power Consumption: 7.5W (~1.5A@5V) Size(WDH): 66 x 105 x 25mm Certification: FCC/CE Mechanical Drawing [66x105x25mm] HDWX-100T (Transmitter) and HDWX-100R (Receiver) Bracket Installation Installation of a Bracket to the device (TX or RX) After install a bracket to the device (HDWX-100T/R), fix the bracket to a desk as a picture below. Note: For the antenna performance in the device, you may fix the bracket side upward to a desk.
5GHz Wi-Fi Channels Because of wireless signal regulations, HDWX-100-TR is managed by two different firmwares (including only available channels in specific nations) according to the shipment locations (US version and Europe version). - US Version: US, Korea and others. - Europe Version: Europe, Japan, and others.
Warranty Information 1 (One) Year Warranty Opticis warrants this wireless HDMI extender to be free from defects in workmanship and materials, under normal use and service, for a period of one (1) year from the date of purchase from Opticis or its authorized resellers.
The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. FCC Statement This device complies with part 15 of FCC Rule.
CE Statement This device complies EN 55022/55024/61000-3 for CE certification. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to EN 55022/55024/61000-3 for CE certification.
© 2014 Opticis Co., Ltd. All Rights Reserved Rev. 2.01, .Oct. 26, 2014 Opticis Locations Headquarters Opticis Co., Ltd. #907, Byucksan Technopia, 434-6 Sangdaewon-Dong, Chungwon-Gu, Sungnam City, Gyeonggi-Do, 462-716 South Korea Tel: +82 (31) 737-8033~8 Fax:+82 (31) 737-8079 www.opticis.com For order support, please contact your Distributor or Reseller. For technical support, check with the Opticis web site www.opticis.com or contact techsupp@opticis.com.
