Manual

ManualsBrandsOptex ManualsElectronicsWireless Outdoor PIR with Inovonics Transmitters

N219

CONTENTS

1 INSTALLATION PRECAUTIONS ............2

1-1 BEFORE INSTALLATION ................2

1-2 PARTS IDENTIFICATION ................3

1-3 KNOCKOUTS ..................................3

2 DETECTION AREA.................................4

2-1 OUTLINE OF DETECTION AREA ...4

2-2 HOW TO REDUCE THE LONG

RANGE DETECTION AREA ............6

2-3 HOW TO DEACTIVATE THE SHORT

RANGE DETECTION AREA ............8

3 PREPARATIONS ..................................10

3-1 TRANSMITTER PREPARATION ...10

3-2 BATTERY PREPARATION ............11

4 INSTALLATION (BATTERY AND

TRANSMITTER) ...................................12

4-1 INSTALLING THE BATTERY .........12

4-2 INSTALLING THE TRANSMITTER

AND BATTERY BOX .....................15

5 INSTALLATION (BRACKET AND

MAIN UNIT) ..........................................16

5-1 INSTALLING WITH BRACKET ......16

5-2 ADJUSTING THE VERTICAL

ANGLE...........................................18

5-3 INSTALLING WITHOUT

BRACKET ......................................18

5-4 WIRING .........................................19

5-5 WALL TAMPER (OPTION) ............20

6 WALK TEST ..........................................22

7 SETTING ..............................................22

8 LED INDICATION .................................26

9 SPECIFICATIONS ................................27

9-1 SPECIFICATIONS .........................27

9-2 DIMENSIONS ................................28

HX-80NRAM

Battery operated with 2 PIRs and

anti-masking

Battery operated

Battery saving logic

Compatible with most wireless transmitter

Long distance detection area (24.0 m)

Flexible detection area setting with plates and flaps

Unique pyro element

Intelligent AND logic

Dual signal processing logic

Vegetation sway analysis logic

Digital anti-masking

•

NO.59-1620-0

INSTALLATION INSTRUCTIONS

High Mount

Outdoor Detector

HX-80NRAM

High Mount

Outdoor Detector

HX-80NRAM

- 1 -

HX-80NRAMEN.indd1HX-80NRAMEN.indd1 2010/08/209:18:412010/08/209:18:41

Summary of content (28 pages)

PAGE 1
NO.59-1620-0 INSTALLATION INSTRUCTIONS High Mount Outdoor Detector N219 HX-80NRAM CONTENTS HX-80NRAM Battery operated with 2 PIRs and anti-masking • Battery operated • Battery saving logic • Compatible with most wireless transmitter • Long distance detection area (24.0 m) • Flexible detection area setting with plates and flaps • Unique pyro element • Intelligent AND logic • Dual signal processing logic • Vegetation sway analysis logic • Digital anti-masking 1 INSTALLATION PRECAUTIONS ............
PAGE 2
1 INSTALLATION PRECAUTIONS 1-1 BEFORE INSTALLATION Warning Failure to follow the instructions provided with this indication and improper handling may cause death or serious injury. Caution Failure to follow the instructions provided with this indication and improper handling may cause injury and/or property damage. mark indicates recommendation. The check The nix sign indicates prohibition.
PAGE 3
1-2 PARTS IDENTIFICATION Bracket base Base Terminals Main unit Battery box PIR1 (Do not touch) Cover Anti-masking infrared LED PIR2 (Do not touch) Bracket Shaft cover LED indicator Lock screw* (M4 × 35 mm) Lens Screw (4 × 20 mm) Accessories Battery leads Lock screw Velcro tapes Dummy battery Screw kit For joint For wall mounting Screw (4 × 20 mm) Screw (4 × 20 mm) Alarm cable *Lock screw attached on bracket base (Transmitter and battery are not included.
PAGE 4
2 DETECTION AREA 2-1 OUTLINE OF DETECTION AREA Plate 1 Upper flap Plate 2 a C g i b d h j Lower flap Flap fix position indicator Plate fix position indicator -4- HX-80NRAM̲EN.
PAGE 5
HX-80NRAM̲EN.indd 5 Top View 2.5 m (8'2") 1.0 0 1.0 0 3 (m) 0.5 1.5 (m) 2.5 1.0 2.0 (m) 3.0 3 (ft.) (ft.) 8 6 4 2 (ft.) 10 8 6 4 2 Side View 3.0 m (9'10") 4 g 20 f 8 30 e 12 40 50 d 16 60 4 20 f 8 30 e 12 40 d 50 16 60 10 4 20 8 30 12 40 50 16 60 • Adjust 2 clicks (2.5° upward) for 2.5 m (8'2") height installation. (Refer to 5-2) Caution>> j i h g 10 • Adjust 1 click (1.25° upward) for 3.0 m (9'10") height installation.
PAGE 6
2-2 HOW TO REDUCE THE LONG RANGE DETECTION AREA To adjust the LONG range of detection, set the upper and lower flaps as follows: Upper flap a Flap fix position indicator C g i b d h j Lower flap 1 Pull out the flap. Note>> If the lower flap is located at the factory default position, slide it out with your thumb. a C g i b 2 Move the flap to the position that corresponds with the desired detection distance. 3 Push the flap until it clicks into position.
PAGE 7
PIR long range detection area reduction The detection distance in the following table can be limited by combining the positions of the flap. Use the following table to determine the positions of the upper and lower flaps that set the required max. detection distance. NOTES: 1. The distance may vary due to environmental conditions. 2. Always walk test the detector to confirm the detection distance. Lower Factory default a c Factory default b d Factory default 24.0 m (80') N.A. N.A. a 18.
PAGE 8
2-3 HOW TO DEACTIVATE THE SHORT RANGE DETECTION AREA To adjust the SHORT range of detection, set the upper and lower plates follows: Plate 2 a C Plate 1 g i Plate fix position indicator b d * Plate 1 and 2 are identical. h j 1 Remove the plate. 2 Insert the plate into the position determined by the required masking distance until it clicks. a C a C g i g i b b 3 If any plate is not used, place it in the storage position. a C g i b Note>> Be careful not to lose the plates.
PAGE 9
PIR short range detection area deactivation Use the following table to determine the positions of the plates that set the required masked area. Lower Not used j h Not used Factory default 1 N.A. i N.A. 2 3 g N.A. N.A. 4 Upper g i h j NOTE: Use only the following combinations for the plate settings. 1 24m(80') 10m 20m 3.0m(9'10") 5m MASK Upper position: Factory default, Lower position: j 24m(80') 2 10m 20m 3.
PAGE 10
3 PREPARATIONS To use the HX-80NRAM, first prepare transmitters and batteries. First check the following flowchart. • Transmitter size Is it possible to accommodate the transmitter in the space between Base and Main unit (Refer to 3-1)? • Battery type • Battery preparation • Reference It is possible to share the batteries of HX-80NRAM. Yes Is the battery in the transmitter Yes Prepare the required batteries CR123, CR2, or 1/2AA? which are the same type as used in the transmitter.
PAGE 11
3-2 BATTERY PREPARATION HX-80N (Refer to 4-1.) -Battery Sharing Power supplied is available from battery box to power HX-80NRAM and the transmitter. Transmitter HX-80NRAM Battery box Note that battery type should be the same as that used for the transmitter. Type Dummy battery Voltage CR123A CR2 1/2AA 1/2AA(*1) 3.0VDC 3.0VDC 3.6VDC 7.2VDC(*1) Number of 3 cells cells to use 3 cells 3 cells 6 cells(*1) *1: 3.6 VDC 1/2 AA battery in series.
PAGE 12
4 INSTALLATION (BATTERY AND TRANSMITTER) -Installation procedure DETERMINING THE DETECTION LENGTH INSTALLING THE BATTERY -Battery Sharing -Non Battery Sharing INSTALLING THE TRANSMITTER AND BATTERY BOX 4-1 INSTALLING THE BATTERY -Battery Sharing Warning Do not use batteries of different capacities (i.e.: mixing new and used batteries) or of different manufacturers and/or types together.
PAGE 13
3 Mount batteries and place cover into correct position using indicator on side of battery box. Hook the cover firmly by the claws on the right and left sides. CR123A×3 (3.0VDC) CR2×3 (3.0VDC) 1/2AA×3 (3.6VDC) 1/2AA×6 (7.2VDC×3) (*1) *1: 3.6 VDC 1/2 AA battery in series. Caution>> To avoid short circuit, do not connect ends of red and black wires together. 4 Open the transmitter cover and remove the battery.
PAGE 14
-Non Battery Sharing Arrange 3 cells each of CR-123A (recommended) or CR2. Warning Do not use batteries of different capacities (i.e.: mixing new and used batteries) or of different manufacturers and/or types together. Not observing the above may result in an explosion, leakage of electrolyte, emission of toxic gases or other outcomes that may be harmful to people and property. Remove the battery box from the main unit. 1 2 Remove the battery box cover. Open the claws (at 2 places).
PAGE 15
4-2 1 INSTALLING THE TRANSMITTER AND BATTERY BOX Using Velcro tape (included in box), install transmitter to main unit. Example of Case 1 Example of Case 2 (Refer to 3-1.) (Refer to 3-1.) Velcro tape Velcro tape 2 Connect the alarm cable to the terminal block of the main unit. 3 Install the battery box into the main unit and connect the necessary wires to the terminal block. (Refer to 5-4 “WIRING”.) Example of Case 1 3 Insert and secure here.
PAGE 16
5 INSTALLATION (BRACKET AND MAIN UNIT) Use the bracket for normal installation. The unit may be installed directly on the wall, without the bracket, only if the following three conditions are met; • The mounting height is less than 3 m (9'10"). • Horizontal adjustment is not necessary. • The ground must be level. 5-1 INSTALLING WITH BRACKET Using the bracket makes it possible to adjust the unit horizontally by ±90°.
PAGE 17
3 Loosen the adjustment screw two turns. 4 Determine the horizontal direction (left or right) of the detector before installing the bracket on the wall. To the right To the left Adjustment screw Caution>> Do not loosen the screw too much. It may disassemble. 5 Open the wiring knockout and Up-Down lock screw knockout for the bracket. 6 Pass wire through base knockout and install base to bracket. 7 Tighten the adjustment screw clockwise.
PAGE 18
5-2 ADJUSTING THE VERTICAL ANGLE For best performance, install detector parallel to the ground. Decide the detection length. To change the detection length, adjust the flap and plate positions. Refer to the 2-2, 2-3 for the details. 3.0 m (9'10") 24.0 m (80') Perform walk test to ensure detector is parallel to the ground. * This description assumes the detection length to be 0 m (0') to 24.0 m (80').
PAGE 19
NO SP NO - + - POWER INPUT (+) (3 - 7.2VDC) POWER INPUT ( ) (3 - 7.2VDC) POWER OUTPUT (+) (3 - 7.2VDC) POWER OUTPUT ( ) (3 - 7.2VDC) ALARM OUTPUT (N.C.) ALARM OUTPUT (COM) ALARM OUTPUT (N.O.) SPARE (Non short) POWER IN TROUBLE OUTPUT POWER OUT NC TROUBLE OUTPUT ALARM COM TAMPER OUTPUT (N.C.) *1 TROUBLE NC NO TAMPER OUTPUT (COM) *1 TAMPER COM NC WIRING TAMPER OUTPUT (N.O.) *1 5-4 + NO TAMPER COM NC TROUBLE OUT (T.O.
PAGE 20
5-5 WALL TAMPER (OPTION) Commercial magnet switch may be mounted as a wall tamper. Magnet switch installation space is provided on the back of the main unit and the bracket. Maximum size of an applicable magnet switch: D 9 mm (0.35") × W 40 mm (1.57") × H 9 mm (0.35") Magnet switch is not included.
PAGE 21
-Installation 1 Install the magnet switch (wall side) to the wall. To determine the installation position, use the “Installation position template” provided on the inside cover of the product package. Open the wiring knockout with suitable tool e.g. screwdriver. 3 Install the other portion of the magnet switch to the back of the main unit or the bracket. Pull the wiring through the knockouts.
PAGE 22
6 WALK TEST 1 Set the DIP switch 1 (WALK TEST MODE) to “ON (TEST)”. 2 Check that the detector detects an object in the intended detection area. The installation has been successful if the LED lights for two seconds after a person walks into the detection area. Detected Not detected Note>> • The switch is set to “ON (TEST)” by factory default. 3 7 Note>> For the walk test, move more than 1.0 m (3'3") away from the detector.
PAGE 23
-WALK TEST MODE DIP switch POSITION NORM. TEST 1 FUNCTION TEST (Factory default • LED will lights when someone detected regardless DIP-SW 6. (Lights up irrespective of the LED ON/OFF (DIPSW 6, refer to page 24) setting) • Alarm will be generated when someone detected regardless DIP-SW 2. NORM. • Normal operation. (Battery saving mode.) • LED is off. (When LED ON/OFF is OFF.) Caution>> After completing a walk test, always set the unit to NORM. position for operation.
PAGE 24
Trouble signal output >> Trouble signal at regular intervals is output after trouble condition continues for a certain period. • ANTI MASKING OUTPUT When an object is placed close to the lens surface, for a period of more than 180 seconds, the IR Anti-Masking circuit will activate and generate a trouble signal. Anti-Masking output will be automatically reset within about one minute after a masking object is removed.
PAGE 25
-PIR AND/OR DIP switch AND OR POSITION FUNCTION AND (Factory default) An alarm is output when both PIR1 and PIR2 detect an object. OR An alarm is output when either PIR1 or PIR2 detects an object. Selecting “OR” mode makes detection range longer than “AND” mode. Walk test to readjust the detection range is required when “OR” is selected. Actual adjustment should be conducted by adjusting the bracket angle.
PAGE 26
8 LED INDICATION Blink Red LED DETECTOR CONDITION Light OFF LED INDICATOR (RED ONLY) Warm-up Blinks for approx. 60 sec. Alarm Lights for 2 sec. Anti-Masking booting (Anti-Masking start up) Blinks 2 times and goes off for 5 sec. and then repeats. Trouble Masking detection output Blinks 3 times and goes off for 3 sec. and then repeats for 180 sec. Low Battery Output Blinks 4 times and goes off for 3 sec. and then repeats.
PAGE 27
9 SPECIFICATIONS 9-1 SPECIFICATIONS Model HX-80NRAM Detection method Passive infrared PIR Coverage 24.0 m × 2.0 m (80' × 6'7") narrow / 20 zones PIR distance limit 6.5 m, 10.0 m, 13.0 m, 18.0 m (22', 33', 42', 59') Detectable speed 0.3 m/s – 1.5 m/s (1'/s – 4'11"/s) Sensitivity 2.0°C (3.6°F) at 0.6 m/s Power input 3 – 7.2 V DC Lithium Battery (CR123A × 3, CR2 × 3, 1/2AA × 3, 1/2AA × 6) Operating voltage 2.5 – 9 V DC Current draw 30 μ A (standby) / 4 mA (max.) at 3 V DC Alarm period 2.0 ±1 sec.
PAGE 28
9-2 DIMENSIONS Using bracket 93 (3.66") 205 (8.07") 93 (3.66") 197.5 (7.78") 197.5 (7.78") 286 (11.26") Without bracket Unit: mm (inch) Unit: mm (inch) The HX-80N series is only a part of a complete system, therefore we cannot accept complete responsibility for any damages or other consequences resulting from an intrusion. As a rough indication of battery change timing, enter the battery type and the date it was first used. Battery type Date (Year/Month) OPTEX CO., LTD.