Manual

ManualsBrandsOptex ManualsElectronicsWireless Ready Outdoor PIR w/ Anti-Masking

-1-

N219

INTRODUCTION

1-1 BEFORE YOUR OPERATION 1

1-2 PARTS IDENTIFICATION 2

1-3 DETECTION AREA 2

PREPARATIONS

2-1 TRANSMITTER PREPARATION 3

2-2 BATTERY PREPARATION 4

INSTALLATION

3-1

DETERMING THE DETECTION LENGTH

3-2 MOUNTING THE BATTERY 5

3-3 MOUNTING THE TRANSMITTER

AND THE BATTERY BOX 7

3-4 MOUNTING THE BRACKET 8

3-5 ADJUSTING THE VERTICAL ANGLE 9

3-6 WIRING 10

SETTING

4-1 FUNCTION 11

4-2 ANTI-MASKING 13

4-3 AREA ADJUSTMENT 14

SPECIFICATIONS

5-1 SPECIFICATIONS 15

5-2 DIMENSIONS 16

INSTALLATION MANUAL

No.59-1547-1

High Mount

Outdoor Detector

High Mount

Outdoor Detector

CONTENTS

By utilizing the OPTEX’s unique pyro-element,

HX series achieves high reliable detection

performance against false and missed alarms.

HX series provides stable and accurate

detection in outdoor severe environmental

conditions.

HX-40RAM: Battery operated model with IR

anti-masking feature.

Installation and connection methods differ

depending on the type and size of the

transmitter battery.

HX -40RAM

Warning Warning Caution

INTRODUCTION

1-1

Do not repair or modify

product

Keep the product away from

the water

Mount the unit securely

BEFORE YOUR OPERATION

Parallel

2.5 - 3.0 m

(8.3 - 10 ft.)

Tilt

The check ( ) mark indicates recommendation.

The cross ( ) mark indicates prohibition.

Summary of content (16 pages)

PAGE 1
No.59-1547-1 INSTALLATION MANUAL High Mount Outdoor Detector N219 CONTENTS HX -40RAM By utilizing the OPTEX’s unique pyro-element, HX series achieves high reliable detection performance against false and missed alarms. HX series provides stable and accurate detection in outdoor severe environmental conditions. HX-40RAM: Battery operated model with IR anti-masking feature. Installation and connection methods differ depending on the type and size of the transmitter battery.
PAGE 2
1-2 PARTS IDENTIFICATION Bracket base Base Screw (3×10 mm) Battery box Terminals Main unit Hood PIR sensor (Don not touch) Anti-masking infrared LED Bracket Shaft cover Screw (4×20 mm) Lock screw (M4×35 mm) Lens LED indicator Cover Area masking seal Lock screw Accessories Battery leads Velcro tapes Dummy battery Alarm cable 1-3 DETECTION AREA Side view (Installation height 3.0 m (10 ft.) ) 8m (26.7ft.) 20 ° 30° 40° 3.0 m (10 ft.) 12 m (40 ft.) Top view 85° 10° (Installation height 2.
PAGE 3
Note : How to change detection length>> Apply area masking seal to limit the detection length. Note that there are three different types of seal. 2 1 3 2 PREPARATIONS To use HX-40RAM, transmitter and battery should be prepared. First check the following flowchart.
PAGE 4
2-2 BATTERY PREPARATION -Battery Sharing Possible Case (See P5) Power supply is available from the battery box to both HX-40RAM and the transmitter. Transmitter HX-40RAM Battery box Note that the battery type shall be the same as that used for the transmitter. Dummy battery Type CR123A CR2 1/2AA 1/2AA(*1) Voltage 3.0VDC 3.0VDC 3.6VDC 7.2VDC(*1) Number of 3 cells 3 cells 3 cells cells to use *1: 3.6 VDC 1/2 AA battery in series.
PAGE 5
3-1 DETERMING THE DETECTION LENGTH Apply masking seal to set the detection length directly on lens. To set an length shorter than the standard 12 meters, select one of the three patterns and apply the appropriate masking seal to the lens. 1 2 1 3 2 3.0 m (10 ft.) 1 4.0 m (13.3 ft.) 5.5 m (18.3 ft.) 3.0 m (10 ft.) 3.0 m (10 ft.) 9.0 m (30 ft.) 3-2 MOUNTING THE BATTERY -Battery Sharing Possible Case Warning Do not use batteries of different capacities (i.e.
PAGE 6
5 Place the battery lead (included in the set) and a dummy battery in the battery case of transmitter. CR123A 6 Connect the alarm cable to the transmitter and close the cover. Transmitter BATTERY LEAD(red) Put the alarm wire outside through the wiring hole BATTERY LEAD(black) CR2 Alarm cable 1/2AA 1/2AA Dummy battery Dummy battery * Twist and cut off the portion that fits the applicable battery type. -Battery Sharing Impossible Case Arrange 3 cells each of CR-123A (recommended) or CR2.
PAGE 7
3-3 MOUNTING THE TRANSMITTER AND THE BATTERY BOX 1 Using a Velcro tape (included in the set), fix the transmitter to the main unit. Example of Case 1 4 Fix the base to the wall surface. 5 Mount the main unit and the lens onto the base. Example of Case 2 (See 2-1) (See 2-1) Velcro tape Velcro tape 2 Connect the alarm cable to the terminal block of the main unit. 3 Install the battery box into the main unit and connect the necessary wires to the terminal block.
PAGE 8
3-4 MOUNTING THE BRACKET Using the bracket makes it possible to adjust the unit horizontally by ± 90 degrees. In cases where the ground is uneven and therefore not parallel with the base of the unit, it is possible to adjust the unit vertically by ± 20 degree (refer to 3-5) Caution>> Do not change the detection length with bracket. Use the masking seal to adjust the detection length. 90° 90° 20° 20° -Bracket installation 1 Remove the up-down lock screw.
PAGE 9
6 Install the base on the bracket. 7 Decide the horizontal angle, and tighten the adjustment screw clockwise. Adjustment screw 8 Caution>> 9 Do not tighten the up-down lock screw. 10 11 Install the Main unit and cover on the base. Complete the 3-5 “ADJUSTING THE VERTICAL ANGLE”. Remove the cover and the Main unit to tighten the up-down lock screw, and install the Main unit and cover on the base again. Fit the shaft cover into the place.
PAGE 10
NO TAMPER COM NC TROUBLE OUT (T.O.) SP NO ALARM COM POWER OUT NC - + POWER INPUT (+) (3 - 7.2VDC) + POWER INPUT (–) (3 - 7.2VDC) - POWER OUTPUT (+) (3 - 7.2VDC) POWER IN POWER OUTPUT (–) (3 - 7.2VDC) + ALARM OUTPUT (N.C.) - ALARM OUTPUT (COM) POWER OUT NC ALARM OUTPUT (N.O.) ALARM COM TROUBLE OUTPUT NO SPARE (Non short) SP TROUBLE OUTPUT TROUBLE NC NO TAMPER OUTPUT (N.C.) *1 TAMPER COM NC TAMPER OUTPUT (COM) *1 NO TAMPER OUTPUT (N.O.
PAGE 11
4 SETTING 4-1 FUNCTION Dip SW 1 WALK TEST MODE 2 BATTERY SAVING TIMER 3 IMMUNITY 4 TROUBLE OUTPUT TYPE 5 TROUBLE OUTPUT TERMINAL 6 LED ON/OFF PIR SENSITIVITY ANTI-MASKING SENSITIVITY (p13) (p13) Do not touch -WALK TEST MODE Dip switch FUNCTION POSITION NORM. TEST 1 •LED will lights at the time of detection regardless DIP-SW 6. (Lights up irrespective of the LED ON/OFF (DIPTEST (factory default) SW 6, see p13) setting) •Alarm will be generated at the time of detection regardless DIP-SW 2. NORM.
PAGE 12
-TROUBLE OUTPUT TYPE Dip switch 4 Select the contact point output form with the TROUBLE OUTPUT TERMINAL. FUNCTION POSITION N.C. N.O. N.C. N.C. signal is output to the TROUBLE OUTPUT (factory default) TERMINAL. N.O. signal is output to the TROUBLE OUTPUT N.O. TERMINAL. * This setting is valid only when the “TROUBLE OUTPUT TERMINAL (factory default)” is selected at Dip switch 5.
PAGE 13
-LED ON/OFF Dip switch 6 FUNCTION POSITION The LED does not light even at the time of OFF (factory default) detection. ON OFF The LED lights when someone is detected.
PAGE 14
-LED INDICATION Red OFF Light Blink STATUS LED Indication Red lights Alarm Warm-up period Anti-Masking booting (Anti-Masking start up) Trouble output Anti-Masking Low Battery Output Red blinks Red blinks 2 times and goes off for 5 sec. This movement is repeated. Red blinks 3 times and goes off for 3 sec. This movement is repeated. Red blinks 4 times rapidly and goes off for 3 sec. This movement is repeated.
PAGE 15
5 SPECIFICATIONS 5-1 SPECIFICATIONS HX-40RAM Model Passive infrared Detection method PIR Coverage 12 m (40 ft.) 85° wide / 94 zones Distance limit 4 m, 5.5 m, 9 m, 12 m (13 ft, 18 ft, 30 ft, 40 ft.) 0.3 – 1.5 m/s (1 – 5 ft/s) Detectable speed 2.0°C (3.6°F) at 0.6 m/s Sensitivity Power input 3 – 7.2VDC Lithium Battery (CR123A×3, CR2×3, 1/2AA×3, 1/2AA×6) 2.5 – 9VDC Operating Voltage Current draw 30µA(standby) / 4 mA (max) at 3VDC 2.0 ± 1 sec Alarm period Warm-up period Alarm output Approx.
PAGE 16
5-2 DIMENSIONS Using bracket and hood Without bracket and hood 148(5.8) 266(10.5) 92(3.6) 205(8.1) 197.5(7.8) 99(3.9) Unit:mm (inch) Unit:mm (inch) The HX-40 series is only a part of a complete system, we cannot accept complete responsibility for any damages or other consequences resulting from an intrusion. Due to our policy of continuous improvement Optex reserves the right to change specification without prior notice.