Manual

ManualsBrandsOptex ManualsElectronicsBattery Operated Outdoor Dual PIR Detector

N219

CONTENTS

1 INTRODUCTION

1-1 BEFORE INSTALLATION ................2

1-2 PARTS IDENTIFICATION ................3

1-3 DETECTION AREA..........................4

2 INSTALLATION

2-1 WIRING DIAGRAM..........................4

2-2 TRANSMITTER PREPARATION .....5

2-3 BEFORE WALL MOUNTING ...........6

2-4 STACKING METHOD ......................7

2-5 SIDE-BY-SIDE AND

TOP-TO-BOTTOM METHOD ........ 11

3 WALK TEST

3-1 WALK TEST ...................................13

4 DIP SWITCH SETTING

4-1 WALK TEST MODE .......................14

4-2 BATTERY SAVING TIMER ............14

4-3 ALARM & TROUBLE OUTPUT ......14

4-4 LED ................................................15

4-5 PIR SENSITIVITY ..........................15

4-6 ANTI-MASKING .............................15

5 OTHERS

5-1 WALL TAMPER (OPTION)

CONNECTION...............................16

5-2 LED LIGHT PATTERN ...................16

6 BATTERY

6-1 HOW TO REPLACE BATTERY .....17

6-2 BATTERY LIFE ..............................18

7 SPECIFICATIONS

7-1 SPECIFICATIONS .........................19

7-2 DIMENSIONS ................................20

FTN-R Battery operated model with 2 PIRs

FTN-RAM FTN-R

with anti-masking

Long battery life

Easy wiring by a connector

Multi fixing transmitter box

Compact design

190° adjustable bracket

Intelligent AND logic

Digital anti-masking (RAM model)

Wall tamper (option)

•

O.59-1646-0 091201

INSTALLATION INSTRUCTIONS

Compact outdoor

detector

Compact outdoor

detector

fit series

- 1 -

Summary of content (20 pages)

PAGE 1
No.59-1646-0 091201 INSTALLATION INSTRUCTIONS Compact outdoor detector N219 fit series FTN-R FTN-RAM Battery operated model with 2 PIRs FTN-R with anti-masking • Long battery life • Easy wiring by a connector • Multi fixing transmitter box • Compact design • 190° adjustable bracket • Intelligent AND logic • Digital anti-masking (RAM model) • Wall tamper (option) - - CONTENTS 1 INTRODUCTION 1-1 BEFORE INSTALLATION.................2 1-2 PARTS IDENTIFICATION.................3 1-3 DETECTION AREA.....
PAGE 2
1 INTRODUCTION 1-1 BEFORE INSTALLATION Warning Failure to follow the instructions provided with this indication and improper handling may cause death or serious injury. Caution Failure to follow the instructions provided with this indication and improper handling may cause injury and/or property damage. The check The nix mark indicates recommendation. sign indicates prohibition. Warning Do not remove the PCB. Caution Do not remove the separate box tamper.
PAGE 3
1-2 PARTS IDENTIFICATION Bracket Separate box Sponge Main unit Separate box cover Main unit cover Lens Sponge Separate box tamper Fixture Sponge for transmitter Connector for POWER and ALARM Connector for TROUBLE Screw kit For joint For wall mounting Screw (M3 × 10 mm) Screw (3 × 20 mm) Plate nut Note>> • Transmitter and battery are not included.
PAGE 4
1-3 DETECTION AREA Top view (m) 5 Side view 0' 5' 15'(ft.) 10' 4 3 Adjustable range: 95° (by 5° pitch) 2 1 1 Adjustable range: 95° (by 5° pitch) 3 4 0 1 2 3 4 10' 5' 0.8 1.0 1.2 2'7" 3'3" 3'11" 0 1 2 3 0' 5' 10' 10' 15' (ft.) 0.8 1.0 1.2 0'(ft.) 0 1 2 3 5 (m) -Overall wiring diagram Transmitter 5 (m) (m) 0 WIRING DIAGRAM Separate box 4 2 m detection length INSTALLATION 2-1 15' (ft.) 0'(ft.
PAGE 5
2-2 TRANSMITTER PREPARATION The transmitter used should have the internal dimensions of H 130 × W 30 × D 35 mm. (H 5.12" × W 1.18" × D 1.38") Unit: mm (inch) 35 (1.38") 130 (5.12") 30 (1.18") Connectors to be used Connector for POWER and ALARM How to position a battery Red Black Connector for TROUBLE - When monitoring ALARM and TROUBLE using the transmitter with 1 external input External input is N.C. External input is N.O. N.C. 3 N.O. ... DIP switch 3: ON (N.O.) ... DIP switch 3: OFF (N.C.
PAGE 6
2-3 1 BEFORE WALL MOUNTING Open the main unit cover. 2 Remove the fixture. Fixture 3 Hold the top of the bracket and remove the main unit. 4 Open the separate box. Bracket Main unit 1 2 Note>> • Be sure to keep connectors installed through the bottom part of bracket after main unit is removed. - - Note>> • Do not remove the separate box tamper.
PAGE 7
5 Select the mounting method. Stacking method (Page 7) Side-by-side method (Page 11) Top-to-bottom method (Page 11) Note>> • Be sure to mount the main unit on the top. 2-4 STACKING METHOD For the side-by-side method and the top-to-bottom method, refer to page 11. 6 Open the knockout. Separate box Wall mounting knockout 7 Separate box cover Joint screw knockout Wiring knockout Wall mounting knockout Joint screw knockout - - Pull the connectors through the wiring knockout.
PAGE 8
Attach the separate box cover and the bracket. Screw (3 × 10 mm) Sponge Plate nut Wiring Sponge Double-sided tape for temporary fixing Screw (3 × 10 mm) Plate nut Notes>> • Be careful not to attach separate box cover upside down. • Be careful not to pinch wires. 9 Hold the top part of the bracket and mount the main unit. 10 Mount the separate box on the wall. Screw (3 × 20 mm) 2 3 100 mm (3.94") Mounting height: 0.8 – 1.
PAGE 9
11 Notes>> Connect the connectors. Main unit side Separate box side Red Black White Yellow Red: Black: White: Yellow: Green Blue Green: Trouble Blue: Trouble Brown Orange Grey Brown: Tamper Orange: Tamper Grey: Tamper Power input (+) Power input (-) Alarm Alarm the transmitter and attach the 12 Install separate box cover. • The tamper output is not exclusive. The Anti-masking and Tamper circuits share the Trouble output. • For the wall tamper wiring connection (option), refer to page 16.
PAGE 10
14 Determine the detection length. (2 m or 5 m) If 2 m is required, rotate the lower lens 180 degrees. Note>> • Do not remove the upper lens. 5 m detection length (Factory default) 2 m detection length Side view 0' Side view 5' 10' 15'(ft.) 0' (m) 0 0'(ft.) (m) 0 0.8 1.0 1.2 2'7" 3'3" 3'11" 0.8 1.0 1.2 0 1 2 3 4 5 (m) 15 Attach the main unit cover. 5' 10' 0'(ft.) 0 1 2 3 walk test. 16 Perform For details, refer to page 13.
PAGE 11
2-5 SIDE-BY-SIDE AND TOP-TO-BOTTOM METHOD For the stacking method, refer to page 7. 6 Open the knockout. Separate box 7 Main unit (Back surface) Wall mounting knockout Pull the wire connectors through wiring knockout. Separate box (Back surface) Wiring knockout (For top-to-bottom method) Wall mounting knockout Wiring knockout Wiring knockout (For side-by-side method) 8 Mount the bracket and the separate box to the wall. 100 mm (3.94") Screw (3 × 20 mm) 83.5 mm (3.
PAGE 12
9 Hold the top part of the bracket and mount the main unit. 10 Connect the connectors. Separate box side 2 3 1 Main unit side Red Black White Yellow Red: Black: White: Yellow: Green Blue Green: Trouble Blue: Trouble Brown Orange Grey Brown: Tamper Orange: Tamper Grey: Tamper Power input (+) Power input (-) Alarm Alarm Notes>> • The tamper output is not exclusive. The Anti-masking and Tamper circuits share the Trouble output. • For the wall tamper wiring connection (option), refer to page 16.
PAGE 13
3 WALK TEST 3-1 1 WALK TEST Set the DIP switch 1 (WALK TEST MODE) to “ON (TEST)”. DIP switch 1 2 3 4 5 6 1 Not detected 2 3 4 5 6 Note>> • The switch is set to “ON (TEST)” by factory default. 3 Set the DIP switch 1 (WALK TEST MODE) to “OFF (NORM)”. DIP switch ON ON 1 2 3 4 5 6 1 Check that LED lights for 2 seconds when the intended object is detected. Detected ON ON 2 2 3 4 5 6 Notes>> • The battery life will be shortened unless the DIP switch 1 is set to “OFF”.
PAGE 14
4 DIP SWITCH SETTING DIP switch ON 1 ON 1 2 3 4 5 6 2 3 4 5 ●: Factory default 6 1 WALK TEST MODE 2 BATTERY SAVING TIMER 3 ALARM & TROUBLE OUTPUT 4 LED 5 PIR SENSITIVITY 6 ANTI-MASKING ON 1 2 3 4 5 6 Do not touch the PCB except for the DIP switch. 4-1 WALK TEST MODE TEST ON 1 2 4-2 3 4 5 6 NORM DIP switch 1 Position Function TEST (Factory default) • The LED lights irrespective of the DIP switch 4 (LED) setting.
PAGE 15
4-4 LED DIP switch 4 ON ON Position ON 1 2 3 4 5 6 OFF PIR SENSITIVITY ON 1 2 3 4 5 6 STD Position LOW STD (Factory default) ANTI-MASKING ON 1 2 3 4 5 6 LED ON Note>> • If the LED lights, check the DIP switch 1 (WALK TEST MODE) setting.
PAGE 16
5 OTHERS 5-1 WALL TAMPER (OPTION) CONNECTION Connect the tamper connector as shown below when connecting a wall tamper (option). Separate box side Main unit side Wall tamper (option) WRS-03 Mounting position Stacking method Side-by-side method and top-to-bottom method Separate box Bracket Sponge 5-2 Sponge LED LIGHT PATTERN The following explains the LED light pattern.
PAGE 17
6 BATTERY The detector shares the battery with the transmitter. Check that the 2.5 to 10.0 V power battery is used for the transmitter. 6-1 1 HOW TO REPLACE BATTERY Open the separate box, and disconnect the transmitter connector. (It is not necessary for the main unit to be opened.) Stacking method Separate box Side-by-side method and top-to-bottom method Separate box Separate box cover Separate box cover 3 3 Connect the connector, and close the separate box.
PAGE 18
6-2 BATTERY LIFE The values indicated are only for reference on condition that the detector is exceptionally operated by the sole battery. It is impossible to indicate the battery life under the normal operation as the battery in the transmitter is shared with the detector. Interval 120 sec CR123A (3 V, 1300 mAh) CR2 (3 V, 750 mAh) 1/2AA (3.6 V, 1000 mAh) Approx. 6 years Approx. 4 years Approx. 5 years Note>> Interval 5 sec Approx. 5 years Approx. 3 years Approx.
PAGE 19
7 SPECIFICATIONS 7-1 SPECIFICATIONS Model Detection method PIR coverage Detection length limit Detectable speed Sensitivity Operation voltage Power input Current draw Alarm period Warm-up period Alarm output Trouble output LED indicator RF Interference Operation temperature Environment humidity Weatherproof Mounting Mounting height Weight Accessories FTN-R FTN-RAM Passive infrared 5 × 1 m (16'5" × 3'3") 2 m, 5 m (6'7", 16'5") 0.3 – 1.5 m/s (1' – 4'11"/s) 2.0°C (at 0.6 m/s) (3.6°F (at 2'/s)) 2.
PAGE 20
35 (1.38") 155 (6.10") DIMENSIONS 155 (6.10") 7-2 42.5 (1.67") 35 (1.38") 42.5 (1.67") Unit: mm (inch) Unit: mm (inch) Note>> • These units are designed to detect an intruder and activate an alarm control panel. Being only a part of a complete system, we cannot accept responsibility for any damages or other consequences resulting from an intrusion. These products confirm to the EMC Directive 2004/108/EC. OPTEX CO., LTD.